Char-Broil 463271309 - Manual

WARNING If “growing” bubbles appear do not use or move the LP cylinder. Contact an LP gas supplier or your fire department! Connecting Regulator to the LP Cylinder 1. LP cylinder must be properly secured onto grill. (Refer to assembly section.) 2. Turn all control knobs to the OFF position. 3. Turn ...

6. Turn the coupling nut clockwise and tighten to a full stop. The regulator will seal on the back-check feature in the LP cylinder valve, resulting in some resistance. An additional one-half to three-quarters turn is required to complete the connection. Tighten by hand only – do not use tools. NOTE...

WARNING For Safe Use of Your Grill and to Avoid Serious Injury:• Do not let children operate or play near grill. • Keep grill area clear and free from materials that burn. • Do not block holes in sides or back of grill. • Check burner flames regularly. • Use grill only in well-ventilated space. NEVE...

Burner Flame Check •Remove cooking grates and flame tamers. Light burners, rotate knobs from HIGH to LOW. You should see a smaller flame in LOW position than seen on HIGH. Perform burner flame check on sideburner, also. Always check flame prior to each use. If only low flame is seen refer to "Su...

Cleaning the Burner Assembly Follow these instructions to clean and/or replace parts of burnerassembly or if you have trouble igniting grill.1. Turn gas off at control knobs and LP cylinder. 2. Remove cooking grates and flame tamers. 3. Remove carryover tubes and burners. 4. 5. Carefully lift each b...

This warranty only applies to units purchased from an authorized retailer. Manufacturer warrants to the original consumer-purchaser only that this product shall be free from defects in workmanship and materials after correct assembly and under normal and reasonable home use for the periods indicated...

PARTS LIST NOTE: Some grill parts shown in the assembly steps may differ slightly in appearance from those on your particular grill model. However, the method of assembly remains the same. 11 NOT Pictured: Key Qty Description A 1 BOTTOM SHELF B 1 TANK SCREW , F/ BOTTOM SHELF C 2 CASTER, LOCKING D 2 ...

ASSEMBLY 2 1/4-20x1/2” screw 1 Attach side panels to bottom shelf using three 1/4-20x1/2” screws, 7mm lock washers, and 7mm flat washers per panel. IMPORTANT: Panel with large hole must Be on left side of bottom shelf. 7mm lock washer 7mm flat washer Attach the two locking casters at the rear of the...

3 4 This step requires two people to lift and position grill head onto cart. Carefully lower the grill head onto the cart, aligning slots at bottom of grill head with posts on cart side panels. Make sure the regulator hose is hanging outside the cart. Grill head must face open side of cart. Place lo...

Upper back panel 6 5 1/4-20x1½” screw 7mm lock washer 7mm flat washer 15 On back of grill, place upper back panel between side panels and above lower back panel. Secure upper back panel, in lower holes, using one 1/4-20x1½” screw, 7mm lock washer, and 7mm flat washer on each side. Do not fully tight...

7 16 Insert tabs on left sideburner shelf assembly into rectangular slots in side of firebox, shown A. Attach rear of shelf using one 1/4-20x3/4” screw, 7mm flat washer, 7mm lock washer and 1/4”nut in upper hole; and using 1/4-20x1½” screw, 7mm lock washer, 7mm flat washer in lower hole, shown B/C. ...

8 Insert front brace under control panel and between cart side panels. Make sure door hinge pins are on the top side and facing the front. Secure using two 1/4-20x1½” screws, 7mm lock washers, and 7mm flat washers on each side. NOTE: MAKE SURE THAT THE FRONT BRACE IS MOUNTED IN THE MOST DOWNWARD POS...

8a 11 10 18 #10-24x3/8” screw Sideburner lid Place sideburner lid onto left shelf and align holes in back of lid with hinge holes. Secure lid to hinges using four #10-24x3/8” screws, 5mm flat washers, 5mm lock washers, and #10-24 hex nuts. NOTE: Fully secure one hinge with screws, washers and nuts, ...

12 B 13 A 19 Place sideburner grate onto sidebruner shelf. . Inside of cart, insert rear heat shield tabs(without holes) into three slots between upper and lower back panels, shown A. Then insert left and right grease tray rails into Attach shield tabs under front brace with three #8x3/8” self-tappi...

14 15 Inside of cart, insert end of tank wire (without hole) into back of lower back panel. end of tank wire Attach other end to bottom of front brace with a #8x3/8” self-tapping screw. Inside of cart, insert tank exclusion wire ends into lower back panel. Attach front right side of wire shelf to th...

16 17 21 Release the cap and nut from electronic ignition module. Attach electronic ignition module and heat shield to the cart right Insert AA battery into ignition module, negative ( – ) end first. Then put on the cap, shown B. ignition module. Total (2) connections, shown C. module. Total (5) con...

21 23 On back of grill, slide grease tray into opening in upper back panel. CAUTION Failure to install grease tray will cause hot grease to drip from bottom of grill with risk of fire or property damage. Grease tray 20 Place cooking grates onto the firebox as shown. Insert the two wire ends at rear ...

EMERGENCIES: If a gas leak cannot be stopped, or a fire occurs due to gas leakage, call the fire department. Emergencies Problem Gas leaking from cracked/cut/burned hose. Gas leaking from LP cylinder. Gas leaking from LP cylinder valve. Gas leaking between LP cylinder and regulator connection. Fire ...

Troubleshooting ( continued ) Problem Burner(s) will not light using ignitor.(See Electronic Ignition Troubleshooting also) Burner(s) will notmatch light. Sudden drop in gasflow or low flame. Flames blow out. Flare-up. Persistent grease fire. Flashback...(fire in burner tube(s)). Unable to fill LP c...

Troubleshooting - Electronic Ignition Problem (Ignition) SECTION I No sparks appear at any electrodes when control knob turned to ; no noise can be heard from spark module. SECTION II No sparks appear at any electrodes when control knob turned to ; noise can be heard from spark module. SECTION III S...