Char-Broil 463247311 - Manual

5 WARNING If “growing” bubbles appear do not use or move the LP cylinder. Contact an LP gas supplier or your fire department! Connecting Regulator to the LP Cylinder 1. LP cylinder must be properly secured onto grill. (Refer to assembly section.) 2. Turn all control knobs to the OFF position. 3. Tur...

6 6. Turn the coupling nut clockwise and tighten to a full stop. The regulator will seal on the back-check feature in the LP cylinder valve, resulting in some resistance. An additional one-half to three-quarters turn is required to complete the connection. Tighten by hand only – do not use tools. NO...

7 WARNING For Safe Use of Your Grill and to Avoid Serious Injury:• Do not let children operate or play near grill. • Keep grill area clear and free from materials that burn. • Do not block holes in sides or back of grill. • Check burner flames regularly. • Use grill only in well-ventilated space. NE...

8 CAUTION If ignition does NOT occur in 5 seconds, turn the burner controls OFF, wait 5 minutes and repeat the lighting procedure. If the burner does not ignite with the valve open, gas will continue to flow out of the burner and could accidently ignite with risk of injury. Turn controls and gas sou...

9 CAUTION Storing Your Grill • Clean cooking grates.• Store in dry location.• When LP cylinder is connected to grill, store outdoors in a well- ventilated space and out of reach of children. • Cover grill if stored outdoors. Choose from a variety of grill covers offered by manufacturer. • Store gril...

3. Remove carryover tubes and burners. 4. 5. Carefully lift each burner up and away from valve openings. We suggest three ways to clean the burner tubes. Use the oneeasiest for you. (A) Bend a stiff wire (a light weight coat hanger works well) into a small hook. Run the hook through each burner tube...

This warranty only applies to units purchased from an authorized retailer. Manufacturer warrants to the original consumer-purchaser only that this product shall be free from defects in workmanship and materials after correct assembly and under normal and reasonable home use for the periods indicated...

PARTS LIST 12 NOTE: Some grill parts shown in the assembly steps may differ slightly in appearance from those on your particular grill model. However, the method of assembly remains the same. Key Qty Description OO 2 BEZEL, F/LID HANDLE PP 2 RECTANGULAR BUMPER, F/ TOP LID QQ 1 LOGO PLATE RR 1 HARDW ...

PARTS DIAGRAM 13 A B B C C D E G H I J K L M N O O O P Q R S T U V X Y Y Z AA BB CC DD EE FF GG HH II JJ KK LL NN MM OO OO PP QQ SS TT TT TT UU VV WW XX YY ZZ AAA FFF BBB DDD EEE RR W CCC HHH F GGG

ASSEMBLY 2 1/4-20x1/2” screw 1 Attach side panels to bottom shelf using three 1/4-20x1/2” screws, 7mm lock washers, and 7mm flat washers per panel. IMPORTANT: Panel with large hole mustbe on Right side of bottom shelf. 7mm lock washer 7mm flat washer Locking caster Bottom shelf Rear Non-lock caster ...

3 4 Place lower back panel between side panels at rear of bottom shelf. Make sure the slots are positioned as shown (A). Secure lower back panel to side panels using two 1/4-20x1/2” screws, 7mm lock washers, and 7mm flat washers on each side. A Lower back panel 1/4-20x1/2” screw 7mm lock washer 7mm ...

5 6 16 Upper back panel 1/4-20x1½” screw 7mm lock washer 7mm flat washer On back of grill, place upper back panel between side panels and above lower back panel. Secure upper back panel, in lower holes, using one 1/4-20x1½” screw, 7mm lock washer, and 7mm flat washer on each side. Do not fully tight...

7 17 Attach rear of shelf using one 1/4-20x3/4” screw, 7mm lock washer, 7mm washer and 1/4” nut in upper hole; using one flat 1/4-20x1½” screw, 7mm lock washer and 7mm flat washer in lower hole, shown B/C . two Attach front of shelf and fascia using 1/4-20x3/4” screws, 7mm flat washers, #8x3/8” self...

8 18 Remove the four screws and washers factory attached to the Auto Clean valve bracket. Position Auto Clean valve bracket beneath right side shelf fascia so that valve stem comes through larger center hole in fascia. Align the four holes on valvebracket with the four holes on fascia. Secure using ...

9 19 Insert tabs on left sideburner shelf assembly into rectangular slots in side of firebox, shown A. Attach rear of shelf using one 1/4-20x3/4” screw, 7mm flat washer, 7mm lock washer and 1/4” nut in upper hole; and using 1/4-20x1½” screw, 7mm lock washer, 7mm flat washer in lower hole, shown B/C ...

10 Insert front brace under control panel and between cart side panels. Make sure door hinge pins are on the top side and facing the front. Secure using two 1/4-20x1½” screws, 7mm lock washers, and 7mm flat washers on each side. NOTE: MAKE SURE THAT THE FRONT BRACE IS MOUNTED IN THE MOST DOWNWARD PO...

8a 13 12 21 #8-32x3/8 " screw Sideburner lid Place sideburner lid onto left shelf and align holes in back of lid with hinge holes. Secure lid to hinges using four #8-32x3/8" screws, 4mm flat washers, 4mm lock washers, and #8-32 hex nuts. #8-32 hex nut 4mm lock washer 4mm flat washer Insert s...

16 24 Release the cap from electronic ignition module on cart right side panel. Insert AA battery into ignition module, negative ( – ) end first. Then put on the cap, shown B. ignition module. Total (2) connections, shown A . module. Total (5) connections. Connect the two wires {(a) and (b)} from th...

17 18 25 Hinge pinon bottomof door Top ofdoor PRESS Right door Front brace Insert hinge pin on bottom of doors into hole in bottom shelf. Press upper hinge pin in front brace, align hinge hole on top of door, and release hinge pin into door. Install flame tamers by sliding one end of each flame tame...

19 20 26 Cooking grate Place cooking grates onto the firebox as shown. Insert the two wire ends at rear of warming rack into holes in back of firebox. Front wires of warming rack rest on sides of firebox. B Place sideburner grate onto sideburner shelf. Then place sideburner griddle onto sidebruner s...

21 22 LP CYLINDER IS SOLD SEPARATELY. Fill and leak check the cylinder before attaching to grill and regulator (see Use & Care section). Once cylinder has been filled and leak checked, place cylinder into hole in bottom shelf. Make sure cylinder valve is facing front of grill. Secure cylinder wi...

28 EMERGENCIES: If a gas leak cannot be stopped, or a fire occurs due to gas leakage, call the fire department. Emergencies Problem Gas leaking from cracked/cut/burned hose. Gas leaking from LP cylinder. Gas leaking from LP cylinder valve. Gas leaking between LP cylinder and regulator connection. Fi...

29 Troubleshooting ( continued ) Problem Burner(s) will not light using ignitor.(See Electronic Ignition Troubleshooting also) Burner(s) will notmatch light. Sudden drop in gasflow or low flame. Flames blow out. Flare-up. Persistent grease fire. Flashback...(fire in burner tube(s)). Unable to fill L...

30 Troubleshooting - Electronic Ignition Problem (Ignition) SECTION I No sparks appear at any electrodes when Electronic Ignition Button is pressed; no noise can be heard from spark module. SECTION II SECTION III Sparks are present but not at all electrodes and/or not at full strength Possible Cause...