Char-Broil 463210011 - Manual

WARNING If “growing” bubbles appear do not use or move the LP cylinder. Contact an LP gas supplier or your fire department! Connecting Regulator to the LP Cylinder 1. LP cylinder must be properly secured onto grill. (Refer to assembly section.) 2. Turn all control knobs to the OFF position. 3. Turn ...

6. Turn the coupling nut clockwise and tighten to a full stop. The regulator will seal on the back-check feature in the LP cylinder valve, resulting in some resistance. An additional one-half to three-quarters turn is required to complete the connection. Tighten by hand only – do not use tools. NOTE...

WARNING For Safe Use of Your Grill and to Avoid Serious Injury:• Do not let children operate or play near grill. • Keep grill area clear and free from materials that burn. • Do not block holes in sides or back of grill. • Check burner flames regularly. • Use grill only in well-ventilated space. NEVE...

Burner Flame Check • Remove cooking grates and flame tamers. Light burners, rotate knobs from HI to LOW . You should see a smaller flame in LOW position than seen on HI . Perform burner flame check on sideburner, also. Always check flame prior to each use. If only low flame is seen refer to "Sud...

Cleaning the Burner Assembly Follow these instructions to clean and/or replace parts of burnerassembly or if you have trouble igniting grill.1. Turn gas OFF at control knobs and LP cylinder. 2. Remove cooking grates and flame tamers. 3. Remove carryover tubes and burners. 4. 5. Carefully lift each b...

This warranty only applies to units purchased from an authorized retailer. Manufacturer warrants to the original consumer-purchaser only that this product shall be free from defects in workmanship and materials after correct assembly and under normal and reasonable home use for the periods indicated...

PARTS LIST NOTE: Some grill parts shown in the assembly steps may differ slightly in appearance from those on your particular grill model. However, the method of assembly remains the same. 11 Key Qty Description A 1 TOP LID, OUTER B 1 INNER INSERT F/ TOP LID C 1 HANDLE F/ TOP LID D 1 LOGO PLATE E 2 ...

2 1/4-20x1/2” screw 1 Attach side panels to bottom shelf using three 1/4-20x1/2” screws, 7mm lock washers, and 7mm flat washers per panel. 7mm lock washer 7mm flat washer Place bottom shelf upside down. Insert Bent U Pin into the caster mounting plate to lock it in place, shown A.Spin the caster clo...

3 4 This step requires two people to lift and position grill head onto cart. Carefully lower the grill head onto the cart, aligning slots at bottom of grill head with posts on cart side panels. Make sure the regulator hose is hanging inside the cart. 14 Regulator hose Left side panel Grill head Righ...

15 5 6 Pull out the two knobs from control panel. Insert temperature gauge stem into the bigger hole above knob bezel, shown A . Make sure the gauge is pushed in as far as it will go, then push the gauge downward until it clips into the panel, shown B / C . Re-install the two knobs. Knob Knob bezel ...

7 A B C 16 Attach foldable side shelf brackets to the tracks under right side shelf using one shoulder screw, 7mm flat washer, 7mm lock washer and 1/4” nut each side, shown A/B . Pull foldable side shelf outward and press it down, shown C . Push foldable side shelf toward right side shelf untill the...

8 17 Fascia, right side shelf Insert flange on right side shelf into side shelf brackets on side of firebox, shown A . Attach rear of shelf using one 1/4-20x1½” screw, 7mm lock washer, and 7mm Attach right side shelf using three 1/4”-20x3/4” screws, 7mm flat washers, 7mm lock washers and 1/4” nuts, ...

10 Attach right and Insert left and right grease tray rails into slots left rails under front brace with two #8x3/8” self-tapping screws, shown B . 18 Right rail Left rail Front Brace Right rail Left rail #8x3/8” self-tapping screw Grease tray opening beneath grease tray opening in upper back panel,...

11 12 Insert hinge pin on bottom of door into hole in bottom shelf. Press upper hinge pin in front brace, align hinge hole on top of door, and release hinge pin into door. Hinge pin on bottom of door Top of door PRESS 19 Door Connect each of the wires from the main burner electrodes into the back of...

13 20 Install flame tamers by sliding one end of each flame tamer into slots at front of firebox and resting opposite end on pins in back of firebox. Back of firebox Front of firebox Flame tamers Pin 14 Assembled warming rack Place cooking grates onto the firebox as shown. Insert the two wire ends a...

On back of grill, slide grease tray into opening in upper back panel. CAUTION Failure to install grease tray will cause hot grease to drip from bottom of grill with risk of fire or property damage. . 15 21 Unscrew on cart right side panel. Insert AA battery into ignitor, negative (—) end first. Repl...

– 22 17 LP CYLINDER IS SOLD SEPARATELY. Fill and leak check the cylinder before attaching to grill and regulator (see Use & Care section). Once cylinder has been filled and leak checked, place cylinder into hole in bottom shelf. Make sure cylinder valve is facing front of grill. Secure cylinder ...

EMERGENCIES: If a gas leak cannot be stopped, or a fire occurs due to gas leakage, call the fire department. Emergencies Problem Gas leaking from cracked/cut/burned hose. Gas leaking from LP cylinder. Gas leaking from LP cylinder valve. Gas leaking between LP cylinder and regulator connection. Fire ...

Troubleshooting ( continued ) Problem Burner(s) will not light using ignitor.(See Electronic Ignition Troubleshooting also) Burner(s) will notmatch light. Sudden drop in gasflow or low flame. Flames blow out. Flare-up. Persistent grease fire. Flashback...(fire in burner tube(s)). Unable to fill LP c...

Troubleshooting - Electronic Ignition Problem (Ignition) SECTION I No sparks appear at any electrodes when Electronic Ignition Button is pressed; no noise can be heard from spark module. SECTION II SECTION III Sparks are present but not at all electrodes and/or not at full strength Possible Cause • ...