Page 2 - MACHINE DATA LOG/OVERVIEW; YOUR DEALER
MACHINE DATA LOG/OVERVIEW 86037910 CEXT7 03/23/07 1 For the name and address of your dealer contact: Windsor Industries YOUR DEALER Name: __________________________________________________________________________________________________ Address: ______________________________________________________...
Page 3 - TABLE OF CONTENTS; OPERATIONS
TABLE OF CONTENTS 86037910 CEXT7 03/23/07 2 Machine Data Log/Overview. ........................1 Table of Contents..........................................2 HOW TO USE THIS MANUAL How to use this Manual.................................1-1 SAFETY Important Safety Instructions ..........................
Page 4 - HOW TO USE THIS MANUAL; REF –
HOW TO USE THIS MANUAL 86037910 CEXT7 03/23/07 1-1 This manual contains the following sections: - HOW TO USE THIS MANUAL - SAFETY - OPERATIONS - MAINTENANCE - PARTS LIST The HOW TO USE THIS MANUAL section will tell you how to find important information for ordering correct repair parts. Parts may be...
Page 5 - SAFETY INSTRUCTIONS; IMPORTANT SAFETY INSTRUCTIONS; When using an electrical appliance, basic precaution; READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE.; SAVE THESE INSTRUCTIONS
SAFETY INSTRUCTIONS 86037910 CEXT7 03/23/07 2-1 IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precaution must always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE. This machine is for commercial use. To reduce the risk of fire, electr...
Page 6 - HAZARD INTENSITY LEVEL; WARNING; WARNING; WARNING; CAUTION
HAZARD INTENSITY LEVEL 86037910 CEXT7 03/23/07 2-2 The following symbols are used throughout this guide as indicated in their descriptions: HAZARD INTENSITY LEVEL There are three levels of hazard intensity identified by signal words - WARNING and CAUTION and FOR SAFETY. The level of hazard intensity...
Page 7 - GROUNDING INSTRUCTIONS
GROUNDING INSTRUCTIONS 86037910 CEXT7 03/23/07 2-3 THIS PRODUCT IS FOR COMMERCIAL USE ONLY. ELECTRICAL: In the USA this machine operates on a standard 15 amp 115V, 60 hz, A.C. power circuit. The amp, hertz, and voltage are listed on the data label found on each machine. Using voltages above or below...
Page 8 - TECHNICAL SPECIFICATIONS; POWER TYPE; ELECTRIC VACUUM MOTOR:; Diaphragm style, internal bypass; GENERAL DIMENSIONS/WEIGHT; quick change
TECHNICAL SPECIFICATIONS 86037910 CEXT7 03/23/07 3-1 POWER TYPE ELECTRICAL: 115 V, 15 A, 60 HZ ELECTRIC VACUUM MOTOR: (1) –3 stage, 1 hp, 99 cfm (2.80 cubic meters/min.) Waterlift –117” (297cm) BRUSH: (1) 15” (38.1 cm.) SOLUTION PUMP: Diaphragm style, internal bypass SOLUTION CAPACITY: 7 gallons (26...
Page 9 - CONTROLS/COMPONENT LOCATIONS
CONTROLS/COMPONENT LOCATIONS 86037910 CEXT7 03/23/07 3-2 1. Main Handle. Used to pull and maneuver machine. 2. Electrical Cord. 3. Pump Switch. Turns on pump and enables spray. 4. Brush/Spray switch. Turns on brush motor and activates electro-valve to dispense solution to floor through jets. Intermi...
Page 10 - Solution Accessory Tool Hookup.; Brush Height Adjustment.; Front Lifting Handle.
CONTROLS/COMPONENT LOCATIONS 86037910 CEXT7 03/23/07 3-3 1 2 3 10 9 1. Solution Accessory Tool Hookup. Used for various auxiliary cleaning tools. 2. Vacuum Hose Door. Used to connect various auxiliary 1 ½ inch cleaning tool vacuum hoses. 3. Brush Height Adjustment. Used to regulate brush height from...
Page 12 - FILLING OPERATIONS
FILLING OPERATIONS 86037910 CEXT7 03/23/07 3-5 FILLING THE CADET NOTE: Use clean bucket of water to fill solution tank Do not put defoamer, solvents, spotter or prespray chemicals in the solution tank. Do not allow water to spill into vacuum motor inlet. Dry spillage from top of solution tank before...
Page 13 - CORRECT; INCORRECT; PUMP VACUUM
OPERATIONS 86037910 CEXT7 03/23/07 3-6 Remove electrical cord and literature from recovery tank. Fill solution tank (see filling operations, page3-5). Adjust brush to proper setting. Note: For good operation the brush must skim the carpet. If circuit breaker trips raise brush to prevent damage to mo...
Page 14 - INTERMITTENT
OPERATIONS 86037910 CEXT7 03/23/07 3-7 Select intermittent or continuous switch setting to turn on brush and start solution spray. The intermittent setting requires the operator to hold the switch in the “on” position with the thumb, and is typically used in small areas where short cleaning passes a...
Page 15 - CLEANING PROCEDURE; shut down; OFF
CLEANING PROCEDURE 86037910 CEXT7 03/23/07 3-8 1ft. (30cm) Release intermittent setting or turn off continuous setting on brush/spray switch approximately 1 foot before ending cleaning pass. Push down on handle to raise vacuum shoe and brush before moving to the next cleaning pass. Overlap brush con...
Page 17 - ACCESSORY TOOL USAGE
ACCESSORY TOOL USAGE 86037910 CEXT7 03/23/07 3-10 Turn on Pump and Vacuum Switch. Note: Be sure intermittent/continuous switch is in center (off) position and brush is in storage position. Squeeze handle on accessory tool to begin cleaning. STEP 3 STEP 4 STEP 1 STEP 2 Use only one of the following a...
Page 18 - MAINTENANCE DAILY
MAINTENANCE 86037910 CEXT7 03/23/07 4-1 SERVICE SCHEDULE MAINTENANCE DAILY WEEKLY QUARTERLY Check machine for cord damage * Check recovery dome and gasket for damage and cleanliness * Check brush – should be clean with no lint or strings attached * Inspect vac shoe for blockage; remove fibers with c...
Page 19 - MAINTENANCE; PERIODIC MAINTENANCE
MAINTENANCE 86037910 CEXT7 03/23/07 4-2 PERIODIC MAINTENANCE Twice a month, flush a white vinegar solution (One quart vinegar to two gallons of water) or anti-browning solution (mixed as directed) through the extractor. This will prevent build-up of alkaline residue in the system. If spray jets beco...
Page 20 - PERFORM THE FOLLOWING REPAIRS.
MAINTENANCE 86037910 CEXT7 03/23/07 4-3 ! WARNING: ONLY QUALIFIED MAINTENANCE PERSONNEL ARE TO PERFORM THE FOLLOWING REPAIRS. VACUUM MOTOR REPLACEMENT 1. Turn off all switches and unplug machine. 2. Remove recovery tank. 3. Remove the (2) screws that fasten the solution tank to the frame, and tilt t...
Page 21 - TO PERFORM THE FOLLOWING REPAIRS.
MAINTENANCE 86037910 CEXT7 03/23/07 4-4 ! WARNING: ONLY QUALIFIED MAINTENANCE PERSONNEL ARE TO PERFORM THE FOLLOWING REPAIRS. BELT REPLACEMENT 1. Turn off all switches and unplug machine. 2. Remove recovery tank and brush. 3. Remove the (2) screws that fasten the solution tank to the frame, and tilt...
Page 22 - SOLUTION PUMP REPLACEMENT; Turn off all switches and unplug the machine.
MAINTENANCE 86037910 CEXT7 03/23/07 4-5 ! WARNING: ONLY QUALIFIED MAINTENANCE PERSONNEL ARE TO PERFORM THE FOLLOWING REPAIRS. SOLUTION PUMP REPLACEMENT 1. Turn off all switches and unplug the machine. 2. Remove recovery tank. 3. Remove the (2) screws that fasten the solution tank to the frame, and t...
Page 23 - WIRING DIAGRAM
WIRING DIAGRAM 86037910 CEXT7 03/23/07 4-6 86268450 PRV NO. 88332 86268830 PRV NO. 88636 862688900 PRV NO. 88655 86268830 PRV NO. 88636 86004480 PRV NO. 41353
Page 24 - TROUBLESHOOTING CHART; PROBLEM CAUSE
TROUBLESHOOTING CHART 86037910 CEXT7 03/23/07 4-7 PROBLEM CAUSE SOLUTION Is the cord plugged in. Plug in cord. Circuit breaker tripped in building. Reset breaker. Faulty switch. Call for service. No Power, Nothing Runs Faulty power cord or pigtail. Call for service. Vacuum circuit breaker tripped. R...
Page 26 - FRAME ASSEMBLY; SEE SOLUTION TANK
FRAME ASSEMBLY 86037910 CEXT7 03/23/07 5-1 1 28 31 30 B 6 9 17 12 A 19 18 21 23 26 3 4 25 24 14 13 7 15 10 11 22 5 8 20 29 27 16 2 SEE SOLUTION TANK
Page 28 - BRUSH ASSEMBLY
BRUSH ASSEMBLY 86037910 CEXT7 03/23/07 5-3 31 25 29 30 18 38 39 16 30 34 17 20 37 26 24 11 8 15 3 26 19 6 21 35 28 29 25 17 32 23 14 30 22 4 27 1 16 7 10 12 13 25 40 41 42 9 33 2 36 5 43
Page 30 - PUMP ASSEMBLY
PUMP ASSEMBLY 86037910 CEXT7 03/23/07 5-5 3 4 13 1016 6 5 11 15 19 18 1 20 7 16 21 17 9 2 12 25 26 23 28 24 26 C 20 27 14 8 (SEE SOLUTION TANK) PRIOR TO SERIAL NO: 1000166663
Page 34 - VACUUM SHOE ASSEMBLY
VACUUM SHOE ASSEMBLY 86037910 CEXT7 03/23/07 5-9 12 11 10 9 8 7 5 4 3 2 1 6
Page 36 - CONTROL PANEL ASSEMBLY
CONTROL PANEL ASSEMBLY 86037910 CEXT7 03/23/07 5-11 12 16 11 4 9 14 5 13 15 19 6 1 18 17 10 7 2 8 3 D SEE SOLUTION TANK 20 21 22 4 23
Page 38 - SOLUTION TANK ASSEMBLY; ASM
SOLUTION TANK ASSEMBLY 86037910 CEXT7 03/23/07 5-13 6 16 14 18 5* 4 2 8 11* 22 18 15 19* 12 17 23 7 3 29 18 10 1 9 21 20 A B D C 7 25 24 27* 26* 28 30 32* 13 ASM SEE FRAME ASM SEE FRAME SEE PUMP ASM SEE CONTROL PANEL ASM
Page 40 - RECOVERY TANK ASSEMBLY
RECOVERY TANK ASSEMBLY 86037910 CEXT7 03/23/07 5-15 16 7 E 12 9 2 6 17 13 8 4 15 5 12 E 18 1 10 11 14
Page 42 - SUGGESTED SPARE PARTS
SUGGESTED SPARE PARTS 86037910 CEXT7 03/23/07 5-17 PART NO. PRV NO. DESCRIPTION SERIAL # FROM NOTES: 86001140 12514 BRUSH, ASM 15 IN 86001100 11045 BELT, 180J6 MICRO-V 86000900 09019 BEARING, 1.125ODX.500IDX.375 86004570 44067 JET BODY, MINI PROMAX BODY 86004580 44068 JET, MINI PROMAX 9504 86026410 ...
Page 43 - WARRANTY ON CHEMICAL USE
LIMITED WARRANTY The foregoing constitutes Century 400’s entire warranty and no other warranty, liability, contingency or responsibility, direct, indirect, consequential or in any way connected with the sale or operation of Century 400 machines or chemical products, either as expressed or implied, w...
