Page 2 - CONTENTS
CONTENTS SPECIFICATIONS ....................................................................................................................................... 1 BLOCK DIAGRAM ...............................................................................................................................
Page 3 - SPECIFICATIONS; Approximate Memory Capacity and File sizes
— 1 — SPECIFICATIONS Image Files Format Snapshots: JPEG (Exif Ver.2.2); DCF (Design Rule for Camera File System) 1.0 standard; DPOF compliant Movies: MPEG-4 AVI format, DivX Audio: WAV Recording Media Built-in Memory 6.0 MB, SDHC Memory Card, SD Memory Card, MMC (MultiMediaCard), MMCplus (MultiMedia...
Page 5 - Power Requirements
— 3 — • Battery: NP-20 (Rated Capacity: 700 mAh) • Recording Medium: SD Memory Card • Measurement Conditions *1 Number of Shots (CIPA) In accordance with CIPA standards Normal temperature (23 ° C ( 73 ° F)), monitor on, zoom operation between full wide and full telephoto every 30 seconds, during whi...
Page 7 - BLOCK DIAGRAM
— 5 — BLOCK DIAGRAM 2.8"-WIDE LCD 7-LED BL LCD/BL KEY Fle xib le-board DISP MO VIE MENU BS LEFT SET UP DO WN RIGHT Strobe WIDE SHUTTER PO WER TELE DA T E REC PLA Y Lenz-Unit Moter Fle xib le-Board Connector 25PIN Connector 27PIN Vcc3.3D Vcc5-2 Vcc3.3D EVcc3.3 Vcc1-0 Vcc3.3D Vcc3.3D MO TER-dr LV ...
Page 8 - TEST MODE; the data inside, which will make the camera unusable.
— 6 — TEST MODE Note: Never perform the menu items unless otherwise instructed. Doing so may cause destruction of the data inside, which will make the camera unusable. ■ To boot the test mode 1. While firmly pressing down both [BS], [PW ON] and [UPPER], turn the power on. 1 : V E R S I O N I N F O2 ...
Page 9 - PROGRAM VERSION UPGRADING
— 7 — PROGRAM VERSION UPGRADING 1. To update the firmware version 1. Prepare the memory card which contains the firmware for EX-S770D in the root directory. EX-S770D.BIN 2. Insert the above memory card into the camera, and set a fully charged battery in the camera. 3. Press the [power button] while ...
Page 10 - How to restore the firmware; Copy the above file to the root directory in the memory card.; NOTE; Remove the battery and the memory card, and then turn the power off.
— 8 — 2. How to restore the firmware 1. Prepare the firmware restoration program and change its name as follows; rom837f-gm11.lbn 씮 saturn.bin NOTE : This software and procedure automatically restores the firmware even if the firmware belongs to a wrong model code. Make sure to use the correct softw...
Page 12 - ADJ TOOL; Introduction
— 10 — ADJ TOOL ■ Introduction Make sure to perform the adjustment by the USB ADJ Tool “adj03SSAW.exe” when replacing the lens unitor the PCB.Here the necessary software, driver and setting are explained to use “adj03SSAW.exe”.Note that the tool, drivers etc. are available only for Windows. 1. Prepa...
Page 16 - VCOM DC ADJUSTMENT; Purpose; The three tools can be obtained from the following global site.
— 14 — VCOM DC ADJUSTMENT ■ Purpose Readjust the VCOM value to minimize the flicker of the LCD after replacing the LCD or the main PCB. ■ Necessary tools 1. Camera (Charge its battery fully)2. Photo diode (S2281-01) : See Fig 1.3. Photo sensor amp (C2719) : See Fig 2.4. BNC-BNC cable (E2573) x 2 : S...
Page 17 - Procedure; a) Tu r n t h e p o w e r o n w h i l e p r e s s i n g “ B S ” a n d “ U P P E R ” .
— 15 — ■ Procedure 1. Camera setting a) Tu r n t h e p o w e r o n w h i l e p r e s s i n g “ B S ” a n d “ U P P E R ” . After pressing “DOWN” key twice, press “BS” and “MENU”.Select "2:USB TCC TEST", and press "SET" button.Select "1:USB TCC ON", and press "RIGHT" b...
Page 19 - PROCEDURE; CURRENT CONSUMPTION
— 17 — THE COUNTERMEASURE FOR "SYSTEM ERROR" System error may occur when the battery is removed while data is written to the internal memory. ■ PROCEDURE 1. Initialize the system. a) Enter the TEST mode.b) Select "3:ROM UPDATE" and press SET button.c) Next, select "5:SYSTEM INITI...
Page 20 - RESETTING THE PLACE OF DESTINATION; For Europe and UK
— 18 — RESETTING THE PLACE OF DESTINATION When the main PCB is replaced, the setting of the destination will be changed, therefore resetting is required.However, when the firmware is changed or fixed, the setting of the destination will be held, therefore resettingis not required.Use the destination...
Page 21 - DISASSEMBLY; * Make sure to use correct screws when assembling since
— 19 — Screws (S1) C-CASE-BA 3. Remove two screws and then remove C-CASE-CA. C-CASE-CA Screws (S1) 4. Remove one screw and then remove C-CASE-ASSY. Screw (S3) C-CASE-ASSY DISASSEMBLY * Make sure to use correct screws when assembling since there are several kinds of them. It is a good idea to sort th...
Page 30 - ASSEMBLY; Strobe assy
— 28 — ASSEMBLY 1. Set the strobe case assy. * Fix it with three hooks. 2. Set the strobe assy. * Fix it with three hooks. Strobe assy Strobe case assy 3. Remove the TRIPOD assy. * Fix it with three hooks. 4. Set the shutter plate. Shutter plate
Page 36 - Strap board
— 34 — 20. Set the front panel. 21. Set the strap board. Strap board (4) Take the front panel assembly off the defective lens. (5) Press on the conductive ring to fix it in place.
Page 37 - Set the power button the shutter button.
— 35 — screws (S2) screws (S4) screw (S4) screw (S3) 24. Assemble with six screws. 22. Set the power button the shutter button. 23. Set the rear panel.
Page 39 - EXPLODED VIEW
— 37 — EXPLODED VIEW 8 7 S4 S1 21 38 35 34 S1 42 S2 41 S3 40 36 S3 10 19 30 11 9 3 5 1 37 27 21 39 12 14 17 20 33 43 S5 S4 16 24 22 S6 23 21 44 44 S4 18 15 16 29 28 2 6 32 45 S1 S2 S1 31 26 25 9 13 4
Page 40 - PARTS LIST; Parts
— 38 — PARTS LIST 1 EX-S770D_SILVER-EU Q T Y 1 1 10252942 CASE ASSY/CENTER TK-RJK509311*001 1 BB C 2 10251069 SHUT-BUTTON/SHUT/A RJK509270-001V01 1 AF C 3 10236155 CUSHION/SHUT RJK508936-001V01 1 AA C 4 10251070 BUTTON/PW/A RJK509269-001V01 1 AE C 5 10251116 TAPE/PW RJK509323-001V01 1 AA X 6 1025483...
Page 42 - PRINTED CIRCUIT BOARD
— 40 — PRINTED CIRCUIT BOARD MAIN PCB (TOP VIEW) FU101 FU100
Page 44 - Overseas Service Division
CASIO COMPUTER CO.,LTD. Overseas Service Division 6-2, Hon-machi 1-Chome Shibuya-ku, Tokyo 151-8543, Japan