Casio DT-800RF- Manual

Chapter 2 • Terminal Setup Running Setup from a Download File The downloaded file is a compressed archive. After extraction using a utility such as WinZip or PKWARE , folders are created on the hard disk as shown in the following figure. Click on the Disk1 folder to view the files as shown in the fo...

Terminal Setup Installation The InstallShield wizard runs and presents the following screen. Click on Next to begin the installation process. Supported Equipment Manual • March, 2006 2-2

Terminal Setup a. To reboot the system immediately, click on Finish . b. To reboot later, click on the option to restart the computer later, and click on Finish . Running the Manager The PowerNet Twin Client Manager is the utility that manages the terminal software and configurations. Select Start ,...

Quick Start Quick Start Quick Start describes how to prepare the Twin Client Manager and the Casio terminal for a Telnet session with the host. Following an initial serial download, the terminal software and configuration is managed automatically, over the wireless network. Configuring the Manager T...

Terminal Setup To set these addresses from the Settings menu, click on Servers and then click on Add . Enter the name of each server, its IP Address and IP port (normally 23 for Telnet servers), and emulation type. Then click on OK . Repeat this step for each telnet server the terminals are required...

Quick Start Saving the Configuration Click File and Save As . Enter a name for this configuration. For the purposes of this example, the name is vt100 . Supported Equipment Manual • March, 2006 2-7

Terminal Setup Download Files to Terminal Select Terminal and Send Program Files to Terminal from the menu bar. The program asks if you want to include configuration files. Select Yes . The Casio Load Options screen appears telling you what actions to perform on the terminal. The first three of thes...

Quick Start Select Execute from the menu bar, then select Link Manager and select Start Link Manager . Note: A shortcut is to just click on the start icon. To stop the download, select Execute then Link Manager Stop , or press the Stop key, the fifth icon from the left under the Download/Upload Util...

Terminal Setup Connecting the Cradle The terminal download requires a serial connection between the terminal and the PC through a cradle. Connect the serial load cable from a serial port on the PC to the communications port of the terminal cradle or to a Casio terminal. In preparation for this downl...

Quick Start 3. Press the Clear key. 4. Select 1: yes . 5. Press the Clear key to return to the system menu. 6. Select 4: Transmit , 4: Utility and 4: Change memory size . 7. Enter 640 and then press the Enter key. 8. Select yes to change the size. 9. Press the Clear key to return to the system menu....

Terminal Setup Standard Setup The default terminal setup is sufficient for most installations. However, to meet site-specific requirements, it may be necessary to customize terminal operation. The standard setup options simplify this process and can be modified using one of the following methods: • ...

Terminal Setup Printer Type This scrolling list selects the attached printer type. The default value is none , indicating no printer is attached. Terminal Setup Using Twin Client Menus The Twin Client terminal software provides an internal menu system for configuring certain parameters on the termin...

Standard Setup Host 0 IP 206.183.67.155 Port 23__ <F3> Save <F7> Quit Press F3 to save the configurations. Edit License Key The client software can be authorized automatically, as described in the next section, Authorizing PowerNet . This menu option permits authorization of each termina...

Terminal Setup Authorizing PowerNet Each PowerNet Twin Client will run for 30 minutes at a time without authorization. Uninterrupted operation for a production environment is the result of authorizing the software. Authorization codes are obtained from the Connect Website at http://www.connectrf.com...

Terminal Setup Software Management In addition to providing functions for the download of files to the terminal via the traditional serial connection, the Twin Client Manager also provides for the management of terminal software and configurations automatically over the wireless network. This sectio...

Software Management Synchronizing Configuration Files Click to put a check in the Synchronize Configuration Files box to enable automatic synchronization of configuration files on the terminal. When the terminal is command booted, its configuration files will be compared with the most recent on the ...

Terminal Setup Creating New Groups New groups, with different configurations, can be created by clicking on Terminal Group Manager , and then clicking the right mouse button as shown. After the new group has been created, the group settings option becomes available for change, as shown below. After ...

Software Management Setting the Segment Checking the Segment button restricts a terminal group to a range of IP addresses. The IP Address can be any valid address on the segment, as it is used only to identify the segment. The setting of the Net Mask can be used to restrict the range. This feature i...

Terminal Setup Any group can be made the default group by clicking on the group, and then clicking on the right mouse button. Then click on the Make Default option. Reassigning Terminals After a terminal has been configured and assigned to the default group, it can be reassigned to a new group by cl...

Chapter 3 • Keypad Configuration Keypad Figures Casio DT-800RF 5250 Left Func Right PWR BS LOCK del reset FNC F9 F17 F7 F8 newline numbovr redraw F17 F7 F18 F8 F19 F9 F4 F5 F6 dup refresh insert stat nullend dup 1 2 3 CLR 0 ENT F1 F2 F3 F4 F5 F6 F7 F8 vw ← home vw → vw ↑ top vw ↓ bot F20 sreq attn f...

Keypad Configuration Casio DT-800RF, 3270 FNC BS LOCK PWR del 7 F8 F9 F F14 F4 F24 F15 F5 F16 F6 pa1 F1 help pa2 F2 print pa3 F3 F17 F18 F19 F4 F5 F6 CLR 0 ENT F1 F2 F3 F4 F5 F6 F7 F8 vw ← home vw → eof vw ↑ vw ↓ F20 sreq attn fld- fld+ F11 F21 F12 F22 F13 F23 clear F10 Left Func Right Left + Right ...

Keypad Configuration Keypad Table The keypad tables in this section are organized by terminal model, keypad configuration, and emulation. The key values represent the default keypad assignments applied to the terminal in Twin Client advanced mode. Table entries that are blank indicate the key is not...

Chapter 4 • Error Message Resolution Guide Twin Client Error Message Resolution Guide Message Reason Solution Reference Tech Note ENTRY TOO LONG; Trying to key beyond the field size. Ensure that you are entering input into the correct field. --- ALPHABETIC ONLY; Trying to key a character that is not...