Casablanca 99199 - User Manual

M6028 • 01/19/17 • © 2017 Casablanca Fan Company

This device complies with part 15 of the FCC Rules. Operation is subject

to the following two conditions: (1) this device may not cause harmful

interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.
This device complies with RSS-210 of Industry Canada. Operation is

subject to the following two conditions: (1) this device may not cause

interference, and (2) this device must accept any interference, including

interference that may cause undesired operation of the device.
This equipment has been tested and found to comply with the limits for

a Class B digital device, pursuant to Part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses

and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio

communications. However there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures: Reorient

or relocate the receiving antenna, Increase the separation between the

equipment and receiver, Connect the equipment into an outlet on a circuit

different from that to which the receiver is connected. Consult the dealer

or an experienced radio/TV technician for help. Note: Any changes or

modifications to the transmitter or receiver not expressly approved by

Hunter Fan Company may void one’s authority to operate this remote

control.

This product conforms to UL Standard 1917.

Rated for ceiling fan max load of 1 amp.

Rated for light wattage of max 300 watts.

WARNINGS

CEILING FAN REMOTE ADD-ON RECEIVER

Model 99199

The Casablanca Add-On Receiver works with

Casablanca pull chain fans and requires a compatible

transmitter (sold separately).

CASABLANCA FAN COMPANY CONTROL LIMITED WARRANTY

This product is warranted to the original purchaser by Casablanca

Fan Company against defects in material and workmanship for

one (1) year from date of purchase. During the warranty period,

we will repair or, at our option, replace a defective product at

no charge. For information on how to obtain service, contact

Casablanca’s Service Department by calling our toll-free number

at 1-888-227-2178. Damage to the product caused by mishandling,

improper installation or modification is not covered by this

warranty. This warranty is given in lieu of all other warranties

expressed or implied. Some states do not allow limitations of time

on an implied warranty, therefore the above limitations may not

apply in every case. This warranty states specific legal rights which

may vary from state to state.

2

4

Install the receiver

INSTALLATION

1

Use the pull chains to set the fan speed to

HIGH

and the light to

ON

.

Prepare fan

Ensure the power is OFF at the outlet box and

wall switch location before proceeding with

installation.

Turn

Pow

er

OFF

Turn off the power

READ AND SAVE THESE INSTRUCTIONS

If you are installing multiple remote-controlled fans

on the same circuit breaker

,

you may need to perform a few extra steps to prevent interference or faulty

operation of your remote controls.

Go to www.CasablancaFanCo.com/FAQs and click “How do I properly install multiple

remote-controlled fans?” for more information.

Choose the hanging system to the right

that most closely resembles the one

used by your fan and place the receiver

as shown.

WARNING:

This receiver cannot be

installed in conjunction with any other

receiver or hard-wired wall control.

Doing so will void your warranty.

Note:

If your canopy is crowded with

excess wire, you may wish to cut the

excess fan wires. Leave a minimum of

8 inches remaining. Strip the fan lead

wires 1/2 inch. Place remaining excess

wire into the ceiling electrical box.

The

bracket and fan must remain properly

grounded.

3

Remove the canopy

If uncertain how to remove it,

reference the fan’s owner’s manual.

With wiring exposed, you may wish

to note existing wire connections or

take a photo for reference.

Remove

the wire connectors that connect

the wires from the outlet box to

the fan, leaving the grounding wires

connected.

Receiver

Canopy

Hanging System 1

Receiver

Canopy

Hanging System 2

Ceiling

Plate

Receiver

Canopy

Hanging System 3

Ceiling

Bracket

Receiver

Fan Body

Cable Tie

For low profile fans, the receiver should

be secured to the ceiling bracket with a

cable tie.

Hanging System 4

To avoid possible electrical shock, before installing or servicing your fan, disconnect the power by

turning off the circuit breakers to the outlet box and associated wall switch location. If you cannot

lock the circuit breakers in the off position, securely fasten a prominent warning device, such as a

tag, to the service panel.