Carrier SERIES 131 58PAV- User Manual
Carrier SERIES 131 58PAV– User Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Disconnect all power to the furnace. DO NOT TOUCH THE; UNIT SIZE; Fig. 1—Dimensional Drawing
- Page 4 – INPUT BTUH; Fig. 2—Air For Combustion and Ventilation; CONFINED
- Page 5 – Step 3—Filter Arrangement; Fig. 3—Air For Combustion and Ventilation; Fig. 4—Side Filter Arrangement
- Page 6 – Step 5—Gas Piping; Fig. 5—Bottom Filter Arrangement
- Page 7 – Step 6—Electrical Connections; Proper polarity must be maintained for 115-v wiring. If; Step 7— Venting; GENERAL; Fig. 7—Typical Gas Pipe Arrangement; GAS
- Page 8 – Table 5—Electrical Data
- Page 10 – PCB
- Page 12 – GAS HEAT
- Page 13 – Table 7—Gas Rate Cu Ft/Hr; BURNER FLAME; Table 8—Canadian Orifice Size
- Page 14 – Fig. 13—Amp Draw Check With Ammeter
- Page 15 – SERVICE TRAINING; • Unit Familiarization
58PAV
Upflow Induced-Combustion Furnaces
Installation, Start-Up, and Operating Instructions
Sizes 045-155, Series 161
NOTE:
Read the entire instruction manual before starting the
installation.
This symbol
→
indicates a change since the last issue.
Index
Page
SAFETY CONSIDERATIONS .....................................................1
Clearances From Combustible Materials .................................1
Dimensional Drawing ...............................................................2
ELECTROSTATIC DISCHARGE (ESD) PRECAUTIONS
PROCEDURE ........................................................................2-3
INTRODUCTION ..........................................................................3
LOCATION ....................................................................................3
General ......................................................................................3
Location Relative to Cooling Equipment ................................3
Hazardous Locations.................................................................3
AIR FOR COMBUSTION AND VENTILATION ...................3-5
Unconfined Space .....................................................................4
Confined Space ......................................................................4-5
FILTER ARRANGEMENT .......................................................5-6
LEVELING LEGS (IF REQUIRED).........................................5-6
GAS PIPING...............................................................................6-7
ELECTRICAL CONNECTIONS ..................................................7
115-v Wiring .............................................................................7
24-v Wiring ...............................................................................7
Accessories ................................................................................7
VENTING ......................................................................................7
START-UP, ADJUSTMENT, AND SAFETY CHECK .........7-14
General ...................................................................................7-8
Sequence Of Operation .......................................................8-11
Heating Mode............................................................................9
Cooling Mode ...........................................................................9
Continuous Blower Mode.........................................................9
Heat Pump Mode.................................................................9-11
Start-Up Procedures ................................................................11
Adjustments .......................................................................11-13
Set Gas Input Rate ............................................................11-12
Set Temperature Rise ........................................................12-13
Set Thermostat Heat Anticipator ............................................13
Check Safety Controls ............................................................14
Checklist ..................................................................................14
SAFETY CONSIDERATIONS
Installing and servicing heating equipment can be hazardous due to
gas and electrical components. Only trained and qualified person-
nel should install, repair, or service heating equipment.
Untrained personnel can perform basic maintenance functions
such as cleaning and replacing air filters. All other operations must
be performed by trained service personnel. When working on
heating equipment, observe precautions in the literature, on tags,
and on labels attached to or shipped with the unit and other safety
precautions that may apply.
Follow all safety codes. In the United States, follow all safety
codes including the National Fuel Gas Code (NFGC) NFPA No.
54-1992/ANSI Z223.1-1992. In Canada, refer to the current
edition of the National Standard of Canada CAN/CGA-B149.1-
and .2-M95 Natural Gas and Propane Installation Codes (NSC-
NGPIC). Wear safety glasses and work gloves. Have fire extin-
guisher available during start-up and adjustment procedures and
service calls.
Recognize safety information. This is the safety-alert symbol
.
When you see this symbol on the furnace and in instructions or
manuals, be alert to the potential for personal injury.
Understand the signal words DANGER, WARNING, and CAU-
TION. These words are used with the safety-alert symbol. DAN-
GER identifies the most serious hazards which will result in severe
personal injury or death. WARNING signifies a hazard which
could result in personal injury or death. CAUTION is used to
identify unsafe practices which would result in minor personal
injury or product and property damage. NOTE is used to highlight
suggestions which will result in enhanced installation, reliability,
or operation.
These instructions cover minimum requirements and conform to
existing national standards and safety codes. In some instances,
these instructions exceed certain local codes and ordinances,
especially those that may not have kept up with changing residen-
tial construction practices. We require these instructions as a
minimum for a safe installation.
ama
®
CANADIAN GAS ASSOCIATION
A P P R O V E D
R
Table 1—Minimum Clearances To
Combustible Materials (In.)
UNIT SIZE
045 AND 070 090-155
Sides
Single-Wall Vent
1
0
Type B-1 Double-Wall Vent
0
0
Back
0
0
Plenum Top
1
1
Vent
Single-Wall Vent
6
6
Type B-1 Double-Wall Vent
1
1
Front
Single-Wall Vent
6
6
Type B-1 Double-Wall Vent
3
3
Service
30
30
NOTES:
1. Provide 30-in. front clearance for servicing. An open door in front of the unit
can meet this requirement.
2. A minimum clearance of 3 in. must be provided in front of the unit for
combustion air and proper operation.
Manufacturer reserves the right to discontinue, or change at any time, specifications or designs without notice and without incurring obligations.
Book 1
4
Tab
6a 8a
PC 101
Catalog No. 565-848
Printed in U.S.A.
Form 58PA-12SI
Pg 1
1-96
Replaces: 58PA-11SI
→
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
ELECTROSTATIC DISCHARGE (ESD) PRECAUTIONS PROCEDURE Electrostatic discharge can affect electronic components.Take precautions during furnace installation and servicing toprotect the furnace electronic control. Precautions will pre-vent electrostatic discharges from personnel and hand toolswhich are ...
Air for combustion must not be contaminated by halogencompounds, which include fluoride, chloride, bromide, andiodide. These elements are found in aerosol sprays, deter-gents, bleaches, cleaning solvents, salts, air fresheners, andother household products. All fuel-burning equipment must be supplied...
2. All air from outside the structure: a. If combustion air is taken from outdoors through vertical ducts, the openings and ducts MUST have at least 1 sq in.of free area per 4000 Btuh of the total input for allequipment within the confined space. (See Fig. 3.) b. If combustion air is taken from the ...
