Campbell Hausfeld WF2058 - Manual
Campbell Hausfeld WF2058 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Lo que no está cubierto por esta garantía:; Responsibilidades del Comprador bajo esta Garantía:; DANGER
- Page 3 – Notes; WARNING; Assembly
- Page 4 – Operation
- Page 5 – Guía de diagnóstico de averías - Soldadora; Guía de diagnóstico de problemas - Soldadura; Maintenance; Consumable and Wear Parts
- Page 6 – Welding Guidelines; Glosario de Terminología Usada por Soldadores
- Page 8 – ADVERTENCIA; Glossary of Welding Terms
- Page 9 – General; Técnicas Básicas para Soldar; CORRIENTE; Instrucciones para soldar; GS
- Page 10 – Mantenimiento; Para reemplazar el cable para soldar; Grosor; Troubleshooting Chart - Welder; Troubleshooting Chart - Welds
- Page 11 – Funcionamiento; Tamaños de las Boquillas de Contacto; Description; For Information About This Product
- Page 12 – AVERTISSEMENT; INSTALACIÓN DEL CABLE; Instalación; LUBICACION
- Page 13 – PELIGRO; PRECAUCION; What is not covered under this warranty:; Responsibilities of purchaser under this warranty:
- Page 14 – Manual de instrucciones y lista de repuestos; Seguridad General; Adjúntela a este manual o archívela en lugar seguro.; Instructions D’Utilisation & Manuel De Pièces; ATTENTION; MÉMENTO: Gardez votre preuve datée d'achat à fin de la garantie!
- Page 16 – ENDROIT; Montage; INSTALLATION DE FILS
- Page 17 – No de Réf Description; Marquage de la Buse de Contacte
- Page 18 – Guide De Dépannage - Soudeur; Guide De Dépannage - Soudures; Fonctionnement; Remarque; Entretien; Épaisseur; Remplacement du Câble d’amenée de courant
- Page 19 – Généralités; Directives De Soudage; Lexique De Termes De Soudage
Heat
Circuit Breaker or
Selector
Slow Blow Fuse
Low
15 amp
High
20 amp
Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described.
Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or
property damage! Retain instructions for future reference.
IN972800AV 11/04
Operating Instructions & Parts Manual
Models WF2050, WF2054, WF2057 & WF2058
Wire Feed
Arc Welder
B U I L T T O L A S T
Description
This Campbell Hausfeld welder is a 70
amp, single phase 115 volt input, wire
feed arc welding machine. This unit is
equipped with infinite wire speed control
to accurately select the proper wire feed
rate needed for various welding
conditions. Internal components are
thermostatically protected.
This welding system is designed for use
with the Flux Cored Arc Welding (FCAW)
process. As delivered from the factory,
this welder can weld with .030” (.8 mm)
or .035” (.9 mm) diameter flux-cored
wire. A starter spool of .035” (.9 mm)
wire is included.
Unpacking
All welding accessories for the
welder are inside the wire feed
compartment on side of welder.
When unpacking, inspect carefully for
any damage that may have occurred
during transit. Make sure any loose
fittings and screws, etc. are tightened
before putting unit into service.
Report
any missing or damaged items by
calling 1-800-746-5641.
Circuit Requirements
This equipment
requires a dedicated
115 volt circuit. Refer to the following
chart for the correct circuit breaker or fuse
rating. Do not run other appliances, lights,
or tools on this circuit while operating
this equipment. Extension cords are not
recommended. Blown fuses and tripped
circuit breakers can result from failure to
comply with this recommendation.
!
CAUTION
General Safety
Danger means a
hazard that will
cause death or serious injury if the
warning is ignored.
Warning means a
hazard that could
cause death or serious injury if the
warning is ignored.
Caution means a
hazard that may
cause minor or moderate injury if the
warning is ignored. It also may mean a
hazard that will only cause damage to
property.
NOTE:
Note means any additional
information pertaining to the product
or its proper usage.
Always keep a fire
extinguisher accessible
while performing arc
welding operations.
!
WARNING
!
CAUTION
!
WARNING
!
DANGER
See page 5 for supply cable
replacement instructions.
Q
UA
LIT
Y
A
SSURANCE
P
ROG
RA
M
Need
Assistance?
Call Us First!
1-800-746-5641
Components and Controls
1. Work Clamp - connects to work
piece.
2. Wire Feed Gun with .035” tip.
3. Power Cord - plug into 115 volt
outlet.
4. On/Off Switch.
5. Infinite Wire Speed Control - turn
clockwise to increase wire speed and
counterclockwise to decrease wire
speed.
6. Heat Selector - Selects welding
power. Two selections are possible;
low and high.
7. Light - illuminates if thermostat has
automatically shut off unit.
8. Wire Feed Compartment.
© 2004 Campbell Hausfeld/Scott Fetzer
For parts, manuals, product & service information
visit
www.chpower.com
Figure 1 - Welder Components and Controls
1
2
3
4
5
6
7
8
REMINDER: Keep your dated proof of purchase for warranty purposes! Attach it to this manual or file it for safekeeping.
Service Record
État de Service
Registro de servicio
Models WF2050, WF2054, WF2057 & WF2058
Modèles WF2050, WF2054, WF2057 & WF2058
Modelos WF2050, WF2054, WF2057 & WF2058
Wire Feed Arc Welder
Soudeur À L’Arc Alimenté En Fil
Soldadora Con Arco Con Alambre Continuo
Date
Date
Fecha
Maintenance performed
Entretien complété
Mantenimiento realizado
Replacement components required
Pièces de rechange exigées
Repuestos requeridos
Operating Instructions and Parts Manual
Manual de Instruccones y Lista de Repuestos
Instructions D’Utilisation et Manuel de Pièces
www.chpower.com
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
39 Sp Garantía Limitada 5-3-1 1. Duración: El fabricante garantiza que reparará, sin costo alguno por repuestos o mano de obra la soldadora o la pistola o los cables que estén dañados bien en material o mano de obra, durante los siguientes periodos después de la compra original:Por 5 años: El transf...
38 Sp Manual de Instruccones y Lista de Repuestos Modelos WF2050, WF2054, WF2057 & WF2058 Notes General Safety(Continued) Keep the head and face out of thewelding fumes. Do not perform electric arc weldingoperations on metals that aregalvanized or cadmium plated, orcontain zinc, mercury, or bery...
37 Sp Modelos WF2050, WF2054, WF2057 & WF2058 5 1 2 3 4 9 8 7 6 10 Figure 12 - Modèlos WF2050, WF2054, WF2057 & WF2058 No. de Ref. Descripción No. del repuesto Ctd. 1 Ensamble de soplete y manguera (fundente revestido, 2,44 m, WF2050 & WF2057) WC403650AV 1 Ensamble de soplete y manguera ...
