Page 2 - ii; Disclaimer
ii Brocade SAN Switch Module: Installation Guide 12 1 Disclaimer Information in this document is provided in connection with Intel. products. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document. Except as provided in Intel's Terms...
Page 3 - iii; Contents
iii Contents Safety and regulatory information ......................................................................... v General Safety ................................................................................................................. viElectrical Safety ...............................
Page 4 - iv
Page 5 - Safety and regulatory information; NOTE; Important Safety Instructions; 重要安全指导; 在执行任何指令之前,请阅读本文档中的所有注意事项及安全声明。参见
v Safety and regulatory information ✏ NOTE The service procedures are designed to help you isolate problems. They are written with the assumption that you have model-specific training on all computers, or that you are familiar with the computers, functions, terminology, and service information provi...
Page 6 - vi; General Safety; xx
vi Brocade SAN Switch Module: Installation Guide General Safety Follow these rules to ensure general safety: • Observe good housekeeping in the area of the machines during and after maintenance. • When lifting any heavy object: 1. Ensure you can stand safely without slipping. 2. Distribute the weigh...
Page 7 - vii; Handling electrostatic discharge-sensitive devices
vii — Performing a mechanical inspection — Working near power supplies — Removing or installing main units • Before you start to work on the machine, unplug the power cord. If you cannot unplug it, ask the customer to power-off the wall box (that supplies power to the machine) and to lock the wall b...
Page 8 - viii; — Use the round ground-prong of the AC plug on AC-operated computers.; DANGER; To Connect
viii Brocade SAN Switch Module: Installation Guide • Use the black side of a grounded work mat to provide a static-free work surface. The mat is especially useful when handling ESD-sensitive devices. • Select a grounding system, such as those in the following list, to provide protection that meets t...
Page 9 - ix; Throw or immerse into water; Use safe practices when lifting.
ix xx CAUTION: If your system has a module containing a lithium battery, replace it only with the same or an equivalent type battery recommended by the manufacturer. If your system has a module containing a lithium battery, replace it only with the same module type made by the same manufacturer. The...
Page 11 - xi; Regulatory specifications and disclaimers; Safety compliance
xi Regulatory specifications and disclaimers Safety compliance USA: UL 60950 - 3rd Edition/CSA 22.2. No. 60950 Canada: cUL certified - 3rd Edition/CSA 22.2. No. 60950- for Canada (product bears the single cUL mark for U.S. and Canada) Europe: Low Voltage Directive, 73/23/EEC TUV/GS to EN60950 2nd Ed...
Page 12 - xii; Electromagnetic compatibility notices (USA); Electromagnetic compatibility notices (International); This product has been tested in accordance too, and complies with; Japan EMC Compatibility:; This is a Class A product based on the standard of the Voluntary; English translation of the notice above:
xii Brocade SAN Switch Module: Installation Guide Electromagnetic compatibility notices (USA) This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harm...
Page 13 - xiii; label which is located visibly on the external chassis.; Device
xiii BSMI (Taiwan): The BSMI Certification number and the following warning is located on the product safety label which is located visibly on the external chassis. RRL Korea: English translation of the notice above: Device User’s Information Class A device This device complies with RRL EMC and is o...
Page 14 - xiv
Page 15 - Installation Guide
1 1 Introducing the Brocade Enterprise and Entry SAN Switch Modules This Installation Guide contains information about setting up and installing the Brocade* Enterprise SAN Switch Module SBCEBFCSW and the Brocade Entry SAN Switch Module SBCEBFCESW into an Intel ® Blade Server Chassis. Throughout thi...
Page 16 - Resource CD; Features and specifications
2 Brocade SAN Switch Module: Installation Guide The switch module has five labels: • One product name label at the right side of the switch module • One product part number and serial number label at the left side of the switch module • One safety certification label at the left side of the switch m...
Page 19 - Switch maintainability:
5 Switch maintainability: • Diagnosis: Power-on self- test (POST) is performed on all functional components except the SFP module. Port operational tests include internal, external, and online tests. • User interface: Light- emitting diode (LED) indicators. Fabric management: • Management methods: —...
Page 20 - Related documentation; This; Safety Information; Installation and User’s Guide
6 Brocade SAN Switch Module: Installation Guide Related documentation This Installation Guide contains setup and installation instructions for the switch module. This documentation also provides general information about the switch module, including getting started, how to configure the switch modul...
Page 22 - Brocade Advanced Performance Monitor User’s Guide; Notices and statements used in this document; The following notices and statements are used in this document:; Major components of the switch module
8 Brocade SAN Switch Module: Installation Guide • Brocade Advanced Performance Monitor User’s Guide : This document contains information about optional advanced performance-monitoring procedures for the Brocade switch modules. Depending on your blade server model, additional documentation might be i...
Page 23 - Brocade Fabric OS Procedures Guide
9 ✏ NOTE The illustrations in this document might differ slightly from your hardware. Figure 1. Fibre Channel switch-module major components. For more information about the components of the information panel, see Chapter 3, “Information panel LEDs and external Fibre Channel ports,” on page 21. For ...
Page 25 - Installing and replacing a switch module; Figure 2 shows the I/O bay locations in the Intel
11 2 Installing and replacing a switch module Figure 2 shows the I/O bay locations in the Intel ® Blade Server Chassis SBCE. Figure 2. SBCE unit (rear view) with I/O bay identification. You must install Fibre Channel switch modules only in I/O bays 3 and 4 of the SBCE unit. The Fibre Channel Expansi...
Page 26 - Installation guidelines; on the; System reliability guidelines; Bay
12 Brocade SAN Switch Module: Installation Guide The following table summarizes the application for each switch module. The second switch module port connection allows for dual paths from the blade server to external Fibre Channel devices. Installation guidelines Before you begin to install the swit...
Page 27 - Handling static-sensitive devices; SBCE unit; Installing a switch module
13 Handling static-sensitive devices Attention: Static electricity can damage electronic devices. To avoid damage, keep static- sensitive devices in their static-protective packages until you are ready to install them. To reduce the possibility of electrostatic discharge, observe the following preca...
Page 28 - Figure 3. Removing the acoustic attenuation module.
14 Brocade SAN Switch Module: Installation Guide Statement 8: xx CAUTION: Never remove the cover on a power supply or any part that has the following label attached. xx CAUTION: Hazardous voltage, current, and energy levels are present inside any component that has this label attached. There are no ...
Page 29 - Blade unit; for at least 2 seconds.
15 6. If you have not already done so, touch the static-protective package that contains the switch module to an unpainted metal part of the Blade unit for at least 2 seconds. 7. Remove the switch module from its static-protective package. 8. Squeeze the release-lever latch to move the insertion arm...
Page 30 - switch module in the; through
16 Brocade SAN Switch Module: Installation Guide Figure 6. Installing a switch module. 11. Raise the release lever until it moves to the upright (closed) position. This locks the switch module in the SBCE unit. ✏ NOTE The switch module takes approximately 60 seconds to complete the power-on self-tes...
Page 31 - Removing or replacing a switch module; Complete the following steps to replace a switch module:; and; “Installation guidelines” on page 12; “Handling static-sensitive devices” on; more information, see the illustration in step
17 module installation instructions, see the documentation that comes with the SFP module. ✏ NOTE SFP module options do not come with the switch module, but are required if you want to use external switch-module ports. 15. Use LC-LC or LC-SC fiber-optic cables to connect the switch-module external p...
Page 35 - Information panel
21 3 Information panel LEDs and external Fibre Channel ports This chapter describes the information panel and LEDs on the switch module and the external Fibre Channel ports on the information panel. Information panel The switch-module information panel contains LEDs and two Fibre Channel ports, as s...
Page 36 - LEDs; errShow; Intel Server Chassis SBCE
22 Brocade SAN Switch Module: Installation Guide The switch-module information panel contains the following components: • Comprehensive LEDs that display the status of the switch module and the network. For more information, see “LEDs.” • Two external Fibre Channel connectors to connect Fibre Channe...
Page 37 - LED name; SBCE
23 Figure 9. Fibre Channel switch-module LEDs. Notes: • The illustrations in this document might differ slightly from your hardware. • An amber LED is lit when a system error or event has occurred. To identify the error or event, check the LEDs on the information panel of the switch module and see T...
Page 39 - SBCE management-module Web interface; Module Tasks; Connecting to the switch module
25 4 Configuring the switch module through the Telnet interface The switch module contains a Telnet server. This server enables a Telnet client to establish a Telnet session with the Fibre Channel switch module to retrieve information or to configure parameters using the command-line interface (CLI)...
Page 40 - Figure 10. Enter Network Password window.
26 Brocade SAN Switch Module: Installation Guide Establishing a Telnet session through the management module Complete the following steps to establish a Telnet session through the Blade management module: 1. In your browser, in the address bar, type http:// xxx.xxx.xxx.xxx , where xxx.xxx.xxx.xxx is...
Page 41 - In the left navigation pane, under; Management; Module Management window opens.
27 Figure 12. Management-module main window. 4. In the left navigation pane, under I/O Module Tasks , click Management . The I/O Module Management window opens. Figure 13. Switch Management window.
Page 42 - Make sure that the IP address is the same in the; Current IP Configuration; New; Scroll down and click; Advanced Switch Management; . A window similar to the one
28 Brocade SAN Switch Module: Installation Guide 5. Click the link for either Bay 3 or Bay 4. A window similar to the one in Figure 14 on page 28 opens. Figure 14. Switch Management window showing switch-module 3 example. 6. Make sure that the IP address is the same in the Current IP Configuration a...
Page 43 - Login
29 8. To start a Telnet session, scroll down to the Start Telnet/Web Session section and click Start Telnet Session . The management-module command-prompt window opens, as shown in Figure 16. Figure 16. Management-module command-prompt window for Fibre Channel switch module. 9. At the Login prompt, ...
Page 44 - To open online help to view the available commands, type; Establishing a Telnet session in a command-line window; Management Module Installation Guide
30 Brocade SAN Switch Module: Installation Guide After you have changed all of the passwords, the command prompt is displayed in a window similar to the one in Figure 18 on page 30. Figure 18. Management-module command-line interface window. 11. To open online help to view the available commands, ty...
Page 45 - At the; password are case sensitive.
31 A Telnet command-prompt window opens. Figure 19. Telnet command-prompt window. 3. At the Login prompt, type the initial default user name, USERID , and press Enter. At the Password prompt, type the initial default password, PASSW0RD (the sixth character is a zero, not the letter O ). The user nam...
Page 47 - Intel
33 5 Configuring the switch module through the Advanced Web Tools interface The switch module contains a Web server interface known as Advanced Web Tools. This server enables a Web-based client to establish a Web-interface session with the Fibre Channel switch module to retrieve information or to co...
Page 48 - GO; Figure 22. Enter Network Password window.; User Name; USERID; Password; PASSW0RD; Inactive session timeout value
34 Brocade SAN Switch Module: Installation Guide Establishing a Web-interface session through the management module Complete the following steps to establish a Web-interface session through the Blade management module: 1. In your browser, in the address field, type http:// xxx.xxx.xxx.xxx , where xx...
Page 49 - Management window opens.
35 Figure 24. Management-module main window. 4. In the left navigation pane, under I/O Module Tasks , click Management . The Switch Management window opens. Figure 25. Switch Management window.
Page 52 - To perform switch-module administrative tasks, click; Admin; field, type the initial default user name,; field, type the initial default password,; Brocade
38 Brocade SAN Switch Module: Installation Guide For I/O bay 4: http://192.168.70.130 The switch-module Advanced Web Tools interface window opens, as shown in Figure 29. Figure 29. Advanced Web Tools interface window (Web-browser view). 3. To perform switch-module administrative tasks, click Admin ,...
Page 53 - Table 3. Optional features
39 6 Advanced features for the Brocade Enterprise and Entry SAN switch modules You can upgrade the switch module to use the following optional features after you purchase them. Except where indicated in Table 3, these features are available for both the Enterprise version and the Entry version of th...
Page 54 - licenseidshow
40 Brocade SAN Switch Module: Installation Guide To activate and use these optional software features, you must purchase the corresponding license keys. For information about these features, see the following documentation on the Resource CD : • Brocade Fabric OS Procedures Guide v4.2.0 or later • B...
Page 55 - A Getting Help and Technical Assistance; Before you call; Check all cables to make sure that they are connected.; Using the documentation
41 A Getting Help and Technical Assistance This appendix contains information about where to go for additional information on Intel products, what to do if you experience a problem with your server platform, and whom to call for service if it is necessary. Before you call Before you call, make sure ...
