Briggs & Stratton 1695287 - Manual

Page 2 - THIS PAGE INTENTIONALLY BLANK

Page 3 - Table of Contents

1 Safety Rules & Information General Warnings ............................................2 Safety Decals ..................................................2 General Operating Instructions Before Operation .............................................3 Mowing with the Catcher ......................

Page 4 - SAFETY DECALS; GENERAL WARNINGS; Attachment Decal; WARNING

2 Safety Rules& Information Read these safety rules and follow them closely. Failure to obey these rules could result in loss of control ofunit, severe personal injury or death to you, or bystanders, or damage to property or equipment. Thetriangle in text signifies important cautions or warnings...

Page 5 - General; After Operation; CAUTION

Before Operation Clear the lawn of all sticks, stones, wire and other debriswhich may be caught or thrown by the mower blades. Check grass condition. If wet, wait until later in the day.If grass is wet, the grass catcher is likely to becomeplugged. For efficient bagging, air circulation under themow...

Page 6 - COUNTERWEIGHT INSTALLATION; SAFETY RULES

InitialInstallation 4 WARNING To avoid serious injury, engage parking brake,disengage PTO, stop engine, remove key anddisconnect spark plug(s) before attempting toinstall, remove or work on the mower. NOTE: In this manual, “left” and “right” are always defined from the standpoint of the operator pos...

Page 7 - HITCH INSTALLATION; Hitch Installation; Left View

5 Hitch Installation HITCH INSTALLATION Hitch Installation 1. Remove 5/16-16 nut (G, Figure 2) from seat deck support capscrew (E). 2. Remove 3/8-16 nut (F) from rear debris guard capscrew (D). 3. Remove 1/2-13 nut (H) from rear of frame (A). 4. Remove 3/8-16 nut (I) from rear transmission support (...

Page 8 - Bag Support and Cover Installation; Bag Support Installation

6 Bag Support and Cover Installation Figure 3. Install Bag and Cover SupportA. Upright SupportB. Bag and Cover SupportC. Support MountD. Mount PinE. Retainer SpringF. Shoulder RestG. Shoulder Bolt E A G B F D C C Bag Support Installation 1. Attach the bag and cover support (B, Figure 3) to the uprig...

Page 9 - Bag Installation and Tube Assembly

7 Bag Installation and Tube Assembly INSTALL COLLECTOR BAGS 1. Raise the cover (A, Figure 5). 2. Attach collector bags (B) using grass bag hanger (C) to bag hanger post (D). A D Figure 5. Install Collector BagsA. Cover B. Collector BagsC. Grass Bag HangerD. Bag Hanger Post B C B A 42” Mowers 42” Mow...

Page 10 - Chute and Tube Installation; Chute Installation

8 Chute and Tube Installation Chute Installation 1. Install 5/16 x 3/4” carriage bolts (D, Figure 7) with 5/16 push nuts (E) to mower deck as shown. 2. Lift discharge deflector(B). 3. Place the holes of the chute (A) onto carriage bolts (D, installed in step 1), sliding the front edge of thechute un...

Page 12 - NORMAL INSTALLATION & REMOVAL; Installation

Normal Installation& Removal 10 Figure 9. Normal Installation & Removal A. Hitch Support AssemblyB. Bag and Cover Support AssemblyC. Shoulder BoltD. Mount PinE. Retainer Spring F. Hinge PinG. Retainer SpringH. Cover Hinge PivotsI. Cover J. BagK. Bag HangerL. Ridge CutoutM. Upper TubeN. Ridge...

Page 13 - Normal Removal; Removal

Normal Removal 11 Removal 1. Unhook rubber strap (P, Figure 9) from pin (Q), then remove tube assembly (O) from chute (R) and fromcover (I). 2. Lift cover (I) and remove bags (J) from bag and cover support assembly (B). Note: Support the cover during the next step. 3. Remove cover (I) by disconnecti...

Briggs & Stratton 1695287 - Manual

Table of Contents:

Summary

Other Briggs & Stratton Models