Briggs & Stratton 1694919 - Manual

Page 3 - Table of Contents; Recommended Accessories

1 Table of Contents Troubleshooting, Adjustments & Service Troubleshooting Chart .....................................8Skid Shoe Adjustment .....................................9Lift Adjustment .................................................9 Initial Setup & Assembly Install Hitch on to Tr...

Page 4 - OPERATING SAFETY; GENERAL WARNINGS; PREPARATION; DANGER; OPERATING ON SLOPES

2 Safety Rules& Information TP-600-4159-01-UV-SMAN OPERATING SAFETY ● Always clear snow up and down the face of slopes,never across the face. Exercise extreme cautionwhen changing direction on slopes. Do not attempt toclear steep slopes. ● Exercise extreme caution when operating on, orcrossing, ...

Page 5 - Features; TRACTOR CONTROLS; A. Blade Angle Control Lever; CONTROL FUNCTIONS

3 Features & Controls TRACTOR CONTROLS Before you begin operating the tractor with the dozerblade attachment, make certain you have: • Read and understood the instructions in the tractor Operator’s Manual. • Become thoroughly familiar with all of the tractor controls and their operation, includi...

Page 6 - WARNING

General OperatingInstructions 4 Checks Before Starting 1. Refer to the Maintenance & Adjustments sections of this manual and perform any needed service. Also,refer to the tractor Operator’s Manual and performany required service. 2. Remove any objects from the work area which might interfere wit...

Page 7 - General Operating Instructions; Daily Storage; Changing Angle of the Blade:; Storage

5 General Operating Instructions Daily Storage 1. Allow tractor engine to cool before storing in any enclosure. 2. After dozing or plowing jobs are completed, hose or brush down the blade to remove excess dirt. 3. Lightly oil all pivot points. Coat bare metal surfaces to prevent corrosion. IMPORTANT...

Page 8 - Notes

Page 9 - Maintenance; Schedule For Normal Care

7 Maintenance Schedule For Normal Care General Lubrication Lubricate the snow blade as shown in Figure 2. Wherean oil can is shown use 30 weight oil. Where a greasegun is shown, use lithium grease. Lubricate the followingareas: • Grease the blade pivot. • Oil the blade lock pawl • Apply grease to th...

Page 11 - Skid Shoe Adjustment

9 Troubleshooting, Adjustments, & Service Figure 3. Skid Shoe Adjustment A – Lock NutB – Skid Shoe Skid Shoe Adjustment On smooth surfaces such as concrete or asphalt, thescraper bar should scrape the surface. On surfaces suchas gravel, the scraper bar should be set high enough sothat it will no...

Page 13 - Install Hitch on to Tractor

11 Initial Setup & Assembly A B Figure 6. Bell Crank InstallationA. Chute Rotator Drive Cover BoltB. Chute Rotator Drive Cover Install Hitch on to Tractor 1. Remove mower deck. 2. Install the bell crank (A, Figure 6) through the front holes (B) of the hitch assembly. NOTE: Make sure that the Lif...

Page 15 - Install Snow Blade Lift Arm

13 Initial Setup & Assembly Install Snow Blade Lift Arm 1. Move the mower deck lift arm to the “LOWERED” position. 2. Install the brass stand-off (A, Figure 10) at the top of the mower deck lift arm (B), using bolt (C) and wash-er (D). 3. Install the lift assist spring (E) from the rear edge of ...

Page 16 - Attaching Snow Blade to Tractor

14 Initial Setup & Assembly Figure 11. Snow Blade AssemblyA. Pivot AssemblyB. Whiz Lock Nut C. Snow Blade AssemblyD. Tension SpringE. EyeboltF. NutG. CapscrewH. Flat WasherI. Spacer A B C Figure 12. Attaching Snow Blade to HitchA. Mounting PinB. Hair PinC. Bell Crank Attaching Pivot Assembly to ...

Page 17 - Travel Height Adjustment

15 Initial Setup & Assembly A E C G D B H F Figure 13. Blade Control Arm InstallationA. Control Arm Support BracketB. Flange NutC. BoltD. EyeboltE. Upper Control ArmF. Lower Control ArmG. NutH. Bolt E C A D B Figure 14. Lower Control Arm InstallationA. BoltB. Adjustment ArmC. Lower Control ArmD....

Page 18 - Removal; Snow Blade Removal; CAUTION

16 Removal Snow Blade Removal 1. Lower the snow blade to the ground. 2. Remove the four (4) hair pins (C, Figure 16) from the control arm (A) and remove the control arm from thesnow blade assembly. 3. Remove the control arm from the tractor. NOTE: The control arm support bracket can be left on thetr...

Briggs & Stratton 1694919 - Manual

Table of Contents:

Summary

Other Briggs & Stratton Models