Zyxel 3356P-LAN - Manuals - manualsarea.com

Page 2 - ii; Limited Warranty

ii Limited Warranty ZyXEL warrants to the original end user (purchaser) that this product is free from any defectsin materials or workmanship for a period of up to two (2) years from the date of purchase.During the warranty period, and upon proof of purchase, should the product have indications offa...

Page 3 - iii; FCC Requirements; Contacting ZyXEL

iii Changes or modifications not expressly approved by the party responsible for compliance couldvoid the user’s authority to operate the equipment. Shielded RS-232 cables are required to beused to ensure compliance with FCC Part 15, and it is the responsibility of the user to provideand use shielde...

Page 5 - Table of Contents; Introduction

v Table of Contents Limited Warranty ii FCC Part 15 Information ii FCC Requirements iii Contacting ZyXEL iii 1 Introduction 1 Unpacking Your Modem 1 Hardware Overview 1 Required Equipment 1 2 Installation 3 Hardware 3 Non-Windows 95 & Windows NT Operating Systems 3 Novell Netware Installation 3 ...

Page 7 - Introduction 1; Introduction; Unpacking Your Modem; One detachable interface cable with RJ-11 cable and plug.; Hardware Overview

Introduction 1 1 Introduction Congratulations on the purchase of your Comet 3356P-LAN Type II PCMCIA card,one of ZyXEL's premier high-performance products. The Comet is world renown forits ability to maintain ultra high speeds and clear, quality connections whilecommunicating around the globe. Unpac...

Page 8 - Introduction

Page 9 - Installation 3; Installation; Hardware; Novell Netware Installation; Follow the steps bellow to complete Novell Netware installation:

Installation 3 2 Installation This chapter describes how to install your Comet hardware. Installation proceduresalso cover Windows 3.x, Windows 95, Windows NT 4.0, and DOS operating systems. Hardware You can insert your Comet with your computer turned on or off. Follow the stepsbelow to complete the...

Page 10 - MS LAN Manager Installation

4 Installation 5. The installation program will install all necessary drivers and modify yourcomputers AUTOEXEC.BAT and NET.CFG directories. 6. Select Yes then press Enter to modify the files. 7. Reboot your computer and the new settings will take effect. For manual installation of ODI drivers, foll...

Page 11 - Installation 5; Select Microsoft LAN Manager from the menu screen.; Reboot your computer and the new settings will take effect.

Installation 5 2. Insert the driver diskette into the floppy drive and set to the appropriate drive(A:\). Then type INSTALL and press Enter. 3. Select Microsoft LAN Manager from the menu screen. 4. Check the card settings. If current settings are correct, select Start Installationand go to step 5. O...

Page 12 - Installation; Packet Driver Installation; Select Packet Driver from the menu screen.; Windows for Workgroups 3.11 Installation

6 Installation Packet Driver Installation 1. Insert the driver diskette into the floppy drive and set to the appropriate drive(A:\). Then type INSTALL and press Enter. 2. Select Packet Driver from the menu screen. 3. Check the card settings. If current settings are correct, select Start Installation...

Page 13 - Windows NT 3.51 Installation; Adding PCMCIA to Your Laptop

Installation 7 11. From the Network Drivers dialog box, press the Add Adapter... button to enterthe Add Network Adapter dialog box. Select Unlisted or Updated NetworkAdapter and click OK. 12. Windows will prompt a Install Driver dialog box; put the driver diskette intofloppy drive then press OK. 13....

Page 14 - Resource Recommendations; Windows NT4.0 Installation

8 Installation 8. Insert the driver disk into floppy disk drive, then enter the correct path (A:\). 9. Select Ethernet + Fax/Modem PC then click OK. 10. Set the appropriate system resources for the Ethernet + Fax/Modem PC Card.Make sure the settings you choose do not conflict with any other devices....

Page 16 - Modem configuration for NT 4.0; Windows 95 Installation

10 Installation 3. Click the HAVE DISK button. 4. Insert the Ethernet + Fax/Modem PC Card driver disk into floppy drive. 5. Enter the correct path for Windows NT 4.0 drivers then press OK. 6. A dialog box will pop up. Give appropriate system resources to the Ethernet +Fax/Modem PC Card; the settings...

Page 17 - Installation 11

Installation 11 4. If current settings are correct, select Start Installation and go to step 6.Otherwise, select Modify Parameters to make changes. 5. Move the cursor to each field you want to make modification and press Enter toset the correct values. Click Enter, then OK. 6. After installation is ...

Page 18 - 2 Installation

Page 19 - Basic Modem Operation 13; Basic Modem Operation; Understanding AT Commands; Using the Windows 95 Hyper Terminal Program

Basic Modem Operation 13 3 Basic Modem Operation This chapter covers the basic commands and techniques involved in modem operation.In many cases, this is the only information you will need in order to get your Comet upand running with communication software, and to start making connections with your...

Page 20 - OK; Dialing and Answering Techniques; Dialing using the ATD Command

14 Basic Modem Operation The next window sets the COM port settings. The settings used for the Comet shouldbe as follows: Bits per second: 115200 Data bits: 8 Parity: None Stop bits: 1 Flow Control: Hardware Click “OK” when finished. After you have done this, save your new connection byselecting “Sa...

Page 21 - Auto-Answer and Hook Controls; Making Your First Connection

Basic Modem Operation 15 Pausing During Dialing: ATDT 9,,555 1212 Dialing Without Waiting for Dial Tone: ATX0D, 555 1212 Originating a call using an Answer Tone: ATDT 555 1212,,,,,,R Redialing the Last Number Called: ATDL Waiting for Five Seconds of Silence: ATDT 800 555 1212 @ 123456,1 714 555 1212...

Page 24 - Dialing Stored Phone Numbers; in the ATDS=n command is actually typed, unlike the; Saving Settings and User Profiles; Default Modem Settings for PC’s; Description

18 Basic Modem Operation The ‘s’ is a number from 0 to 3 that represents the location in memory that the phonenumber is to be stored, and the ‘n’ is the phone number itself. Example: To store the number ‘1-714-555-1212’ in memory location ‘2’, type: AT&Z2=17145551212<Enter> You can store u...

Page 25 - Basic Modem Operation 19; Use both V.42bis and MNP 5 data compression

Basic Modem Operation 19 ATCommand Description %C1 Use both V.42bis and MNP 5 data compression

Page 26 - 0 Basic Modem Operation

Page 27 - AT Command Set Summaries 21; AT Command Set Summaries; Basic AT Command Set

AT Command Set Summaries 21 4 AT Command Set Summaries Basic AT Command Set Command Options Function & Description A/ Re-execute the last command string <anykey> Terminate the current connection attempt when entered in handshakingstate All the following commands require an “AT” prefixA Go ...

Page 28 - 2 AT Command Set Summaries

22 AT Command Set Summaries Command Options Function & Description M2 Speaker always on M3 Speaker off during dialing and on until carrier present Nn Select negotiate handshake N0 When originating or answering, handshake only at the communicationrate specified by S37 register and “ATBn” and no f...

Page 29 - AT Command Set Summaries 23; Extended AT& Command Set

AT Command Set Summaries 23 Command Options Function & Description Z0 Reset and recall user profile 0. Either Z0 orZ1 restores the same single profile. * Manufacturer default Extended AT& Command Set Command Options Function & Description &Cn Data carrier detect option &C0 State ...

Page 30 - 4 AT Command Set Summaries; Extended AT\ Command Set

24 AT Command Set Summaries Command Options Function & Description &W Store active configuration into the modem’s NVRAM &Zn=x Store telephone number n=0 to 3x=<string> see also the dial modifier in ”ATDn” commandThe maximum number of digits per string is 40. * Manufacturer default ...

Page 31 - AT Command Set Summaries 25; Extended AT- Command Set

AT Command Set Summaries 25 Extended AT- Command Set Command Options Function & Description -Cn Data calling tone options -C0 * Disable data calling tone -C1 Enable data calling tone (the freq. is 1,300 Hz with a cadence of 0.5 sec.ON and 2 sec. OFF) • Manufacturer default

Page 32 - 6 AT Command Set Summaries

Page 33 - Status Registers & Result Codes 27; Status Registers & Result Codes

Status Registers & Result Codes 27 5 Status Registers & Result Codes Register Dec. Function & Description Default S0= 0 - 255 Set the number of the rings required before the modemautomatically answers a call. Set “S0=0” to disable auto-answer mode. 000 S1= 0 - 255 Count the incoming ring...

Page 34 - 8 Status Registers & Result Codes

28 Status Registers & Result Codes Register Dec. Function & Description Default 0, 2 Hang up. 1, 3 Fall back to an async connection. 4, 6 Attempt MNP mode. If MNP fails, hang up. 5, 7 Attempt MNP mode. If MNP fails, fallback to asyncconnection.. S37= Desired DCE speed (line speed). 000 0 Max...

Page 35 - Status Registers & Result Codes 29; Result Code Options; Result Code Options Table

Status Registers & Result Codes 29 Register Dec. Function & Description Default Don’t use S36=1 or 3, and S48=7 LAPM or async S36=1 or 3, and S48=128 Async S36=4 or 6, and S48=7 LAPM, MNP or hang up S36=4 or 6, and S48=128 MNP or hang up S36=5 or 7, and S48=7 LAPM, MNP or async S36=5 or 7, a...

Page 36 - 0 Status Registers & Result Codes; Extended Result Code Options Table

30 Status Registers & Result Codes ATV0 ATV1 X0 X1 X2 X3 X4 X7 59 CONNECT 31200 EC * # # # # 60 CONNECT 33600 EC * # # # # 70 CONNECT 32000 EC * # # # # 71 CONNECT 34000 EC * # # # # 72 CONNECT 36000 EC * # # # # 73 CONNECT 38000 EC * # # # # 74 CONNECT 40000 EC * # # # # 75 CONNECT 42000 EC * #...

Page 37 - Status Registers & Result Codes 31

Status Registers & Result Codes 31 ATV0 ATV1 W0 W1 W2 W2\V0 40 CONNECT 300 9 9 40 CONNECT 300 EC * 9 9 55 CONNECT 21600 9 55 CONNECT 21600 EC * 9 56 CONNECT 24000 9 56 CONNECT 24000 EC * 9 57 CONNECT 26400 9 57 CONNECT 26400 EC * 9 58 CONNECT 28800 9 58 CONNECT 28800 EC * 9 59 CONNECT 31200 9 59...

Page 38 - 2 Status Registers & Result Codes

32 Status Registers & Result Codes NoEC No error control and data control protocols