Page 2 - Copyright; Disclaimer; Trademarks
Prestige 100MH Quick Start Guide ii Prestige 100MH PSTN Router/Hub Copyright Copyright © 1998 by ZyXEL Communications Corporation. The contents of this publication may not be reproduced in any part or as a whole, transcribed, stored in a retrieval system, translated into any language, or transmitted...
Page 3 - Table of Contents
Prestige 100MH Quick Start Guide iii Table of Contents Chapter 1 Before You Begin 1.1 Purpose Of This Guide .................................................................................... 1 1.2 Who Should Not Use This Guide: .................................................................... 1...
Page 5 - Chapter 1; Purpose Of This Guide
Prestige 100MH Quick Start Guide 1 Chapter 1 Before You Begin 1.1 Purpose Of This Guide This guide provides instructions on how to setup your new Prestige and Windows 95/NT workstations for Internet access using the Prestige Web Configurator (PWC). The Prestige Web Configurator provides a quick, sim...
Page 6 - Information From Your ISP; Prestige
Prestige 100MH Quick Start Guide 2 θ One Telephone Cable with RJ-11 Connectors θ One DB -25(male)/DB -9(female) Converter θ One Console RJ-45/DB-25(female) Cable θ One Ethernet 10Base-T cable θ One Prestige Web Configurator CD ROM θ One Prestige Series User's Manual θ One Warranty Registration Card ...
Page 7 - Prestige’s Default TCP/IP Settings; Your
Prestige 100MH Quick Start Guide 3 1.5 Prestige’s Default TCP/IP Settings 1.5.1 IP Address and S ubnet Mask Your Prestige is pre-configured in the factory with IP Address of 192.168.1.1 and subnet mask of 255.255.255.0 (Class C). 1.5.2 DHCP Setting Your Prestige has a built- in DHCP (Dynamic Host Co...
Page 9 - Chapter 2; The following diagrams depict the cabling for the
Prestige 100MH Quick Start Guide 5 Chapter 2 Cabling & Installation The following diagrams depict the cabling for the Prestige . After you have completed the cabling, proceed to Chapter 3: Windows 95 Quick Start or Chapter 4: Windows NT Quick Start . 2.1 Prestige 100MH Computer POWER CONSOLE PHO...
Page 11 - Chapter 3; TCP/IP Configuration
Prestige 100MH Quick Start Guide 7 Chapter 3 Windows 95 Quick Start This chapter shows you the step-by-step instructions to configure your Windows 95 workstations for Internet access. 3.1 TCP/IP Installation You must first install TCP/IP protocol on each Windows 95 workstation before you can use it ...
Page 14 - Otherwise, you will not be able to access the Internet.
Prestige 100MH Quick Start Guide 10 Step 3. The TCP/IP Properties dialog with IP Address tab will appear as shown below. Step 4. Select Obtain an IP address automatically if your ISP did not assign you a block of registered IP addresses (most cases); otherwise, select Specify an IP address and enter...
Page 15 - Select the; On the; tab, highlight any installed gateways and click the; button
Prestige 100MH Quick Start Guide 11 Step 5. Select the WINS Configuration tab, and click Disable WINS Resolution . Step 6. On the Gateway tab, highlight any installed gateways and click the Remov e button until there are none listed.
Page 19 - Chapter 4; From the
Prestige 100MH Quick Start Guide 15 Chapter 4 Windows NT Quick Start This chapter shows you the step-by-step instructions to configure your Windows NT workstations for Internet access. 4.1 TCP/IP Installation You must first install TCP/IP protocol on each Windows NT workstation before you can use it...
Page 22 - you will not be able to access the Internet.
Prestige 100MH Quick Start Guide 18 Note: Do not assign arbitrary IP address and subnet mask to your workstations. Otherwise, you will not be able to access the Internet. Step 5. On the DNS tab, Enter a unique name for the workstation in the Host Name box. Enter your domain name in the Domain box if...
Page 23 - tab, make sure the toggle button of
Prestige 100MH Quick Start Guide 19 Step 6. On the WINS Address tab, make sure the toggle button of Enable DNS for Windows resolution is not checked.
Page 24 - Click on the; button at the bottom to save and close the; button to save and close the; Repeat the above steps for each Windows NT workstation on your LAN.
Prestige 100MH Quick Start Guide 20 Step 7. Click on the OK button at the bottom to save and close the TCP/IP Properties dialog. Step 8. Click on the OK button to save and close the Network control panel. Repeat the above steps for each Windows NT workstation on your LAN.
Page 25 - Chapter 5; Installing PWC Components
Prestige 100MH Quick Start Guide 21 Chapter 5 Prestige Web Configurator Setup The Prestige Web Configurator (PWC) is a JAVA based system that provides you a quick, simple, and intuitive way to configure your Prestige . Using a “point-and-click” Web-based Graphical User Interface (GUI), you can confi...
Page 26 - Visual; and; buttons to select the PWC components that have not been; button to install the selected component.
Prestige 100MH Quick Start Guide 22 Note: The ZyXEL CD Installer Program (Startup.exe) requires the Microsoft ® Visual Basic 5 Runtime libra ries. On some systems you may get the message "Error Starting Program" when trying to start the CD-ROM Installer. If this should occur, use the Windows...
Page 27 - Starting the Prestige Web Configurator; To start PWC, select Start
Prestige 100MH Quick Start Guide 23 Step 3. After you have completed installing all the required components, click the Exit button. Step 4. Run the JAVA Activator Control Panel, which in located in the JAVA Activator 1.1 EA2 folder of your Start/Programs gr oup. Step 5. Make sure the settings match ...
Page 29 - Customer Support; ZyXEL Communications Corporation; ZyXEL
Prestige 100MH Quick Start Guide 25 Customer Support ZyXEL Prestige 100MH If you have questions about your ZyXEL products or desire assistance, contact ZyXEL Communications Corporation in one of the following ways. Contacting ZyXEL E-mail Technical Support [email protected] in North America Support@...