Zenith PRO895X - Manuals

P A G E 5 3276-A SPECIFICATIONS PRO895X Note: Specifications are subject to change without prior notice. Optical PROJECTION SYSTEM — CRT; 7-inch High Performance LiquidCooled Tubes, 5-inch active phosphor area, 90 degree deflectionangle, Super Oxide Cathodes.LENSES — High resolution color corrected ...

206-3700 P A G E 6 STANDARD CONNECTIONS CONNECTING COMPUTER VIDEO SOURCES Connect a video source such as a computer: PC, Laptop, or Notebook type. CONNECTING VIDEO AND S-VIDEO SOURCES Connect video sources with a tuner, (VCR) or other video sources such as a DVD player or satellite receiver. To hook...

P A G E 7 3276-A STANDARD CONNECTIONS CONNECT OR PIN WIRING REFERENCE

206-3700 P A G E 8 E N T E R Shows Source/Time Display M E N U Accesses on-screen menus P O W E R O N I N D I C AT O R P O W E R On/Off Switch Red, Green, Blue (RGB)Horizontal/Vertical input jacks C O M P O S I T E V I D E O I N P U T C O M P O S I T E V I D E O L O O P O U T J A C K (Set LOOP switc...

P A G E 9 3276-A REMOTE CONTROL Red, Green, Blue Setup Notes • Do not place heavy objects on top of the remote control keys. Prolonged unintentional operation of the remote shortens the usable life of the batteries. • Remove the batteries if the remote control will not be used for a month or more. •...

P A G E 1 0 The PRO895X HD Projection Display system is a high reso-lution multiple signal format display monitor. It uses 7”high performance liquid cooled CRTs. Each CRT has a 5”active phosphor area and a 90 degree deflection angle. TheCRTs use high-resolution color corrected multi-layeredhybrid le...

P A G E 1 1 3276-A Vertical Active - vertical deflection yoke drive is present in the 9-1510 module. Video Enable - all conditions are ready for high voltage to turn on via the 9-1504 mo REAR VIEW Be sure to read and understand the setup section beforeyou attempt to install a PRO895X system; you wil...

P A G E 1 3 206-3634-A The PRO895X is supplied with the MBR3470T / 3468PT anda universal customer remote control. For most servicing sit-uations, the MBR3470T / 3468PT is required. The MBR3470T/ 3468PT has the special functions needed for geometry /convergence adjustments and system setup functions ...

1. When you enter the setup mode, the system is in the “Geometry Mode” (the shape controls adjust all three colors at the same time). To adjust an individual color (i.e. Red to adjust SKEW), you must press the “Red” key. This will put the system into the “Convergence Mode” (the shape controls adjust...

I. SYNC INPUTS There are three Sync signal inputs for use with RGB sources:1. SYNC-ON-GREEN (SOG) - - this is through the Green video input BNC jack, terminated 75 ohms. 2. HORIZONTAL/COMPOSITE (H / Comp) - - through a BNC jack on the 9-1515 Combo module, software switchable termination 2K/75 ohms. ...

Courtesy of Draper Shade & Screen One of the most important decisions in screen selection is todetermine the correct size of screen based upon- 1. The dimensions of the audience area.2. The projection format, or formats, to be used. In some situations, these two questions yield the same answer; ...

206-3634 P A G E 1 8 SETUP AND ALIGNMENT PROCEDURE PROCEDURE OVERVIEW There are several situations to consider when performing the setupprocedure for the PRO895X System. The setup procedure will varydepending on the required physical and signal configuration. The simplest setup is that of a “factory...

P A G E 1 9 206-3634 SETUP REFERENCES Setup Menus 9 - 1505 Module 9 - 1510 Module 9 - 1509 Module Top Edge Top View

206-3634 EXAMPLES OF DISPLAY SETUP DISTANCES AND CENTER POINTS “A” * “B” Screen Projection Display “Peerless” Width Distance Center Mount Center 48” 58 5/8” 26 3/8” 11” 60” 72 7/8” 30 3/4” 11” 80” 96 3/8” 38” 11” 96” 115 1/4” 43 5/8” 11” 120” 143 1/2” 52 3/8” 11” 144” 171 7/8” 61” 11” 160” 190 5/8” ...

P A G E 2 1 206-3634 SYSTEM ALIGNMENT Mount Bracket Center 11" from Front Panel Under the Green CRT Center 11 III. PRELIMINARY ALIGNMENT SETUP The following procedures are intended for complete“Geometry/Convergence” setup. Use the customer’s signal fordoing phase, and size adjustments. You can u...

Continued from previous page Verify spot alignment by rotating Green electrical focus slightlyclock-wise to counter clock-wise. The Dot shape should not tail orflair. The bright area should remain in the center of the haloedarea. Refer to the figure below. If this test shows a need for astimatator a...

SYSTEM ALIGNMENT P A G E 2 4 206-3634 Continued from previous page IV. Final Detailed Geometry/Convergence Setup Use the video patterns generated by the customer’s signal sourcefor final alignment. If this is not possible, use the internal crosshatch pattern only to do the geometry and convergence. ...

P A G E 2 5 206-3634 SYSTEM ALIGNMENT 1. SIZE H. Size Set to fill screen at C and D. (Useexternal source not internal test pattern) 2. SIZE V. Size Set to fill Screen at A and B. (Useexternal source not internal test pattern.) 3. LIN TB LR H. Lin L-R Set equal widths CZ=ZD 4. LIN TB LR V. Lin T-B Se...