Page 2 - TECHNICAL ASSISTANCE
2 Congratulations on the purchase of your YAZOO/KEES mower. This manual has been prepared for the owners and operators of the models called out on the front cover of this manual. Read,understand and follow the safety and operating instructions. Continuous dedication to improve our products require t...
Page 3 - CONTENTS
3 CONTENTS SAFETY INSTRUCTIONS .................... 4 General use and safety rules ...... 4,5 Driving on slopes ........................ 5 Children safety ............................ 5 Service safety ............................. 5,6 Transportation ............................ 6 PRESENTATION .........
Page 4 - SAFETY INSTRUCTIONS; General use and safety rules:
4 SAFETY INSTRUCTIONS IMPORTANT ! This cutting machine is capable of amputat-ing hands and feet and throwing objects.Failure to observe the following safetyinstructions could result in serious injury ordeath. FIG - 1 General use and safety rules: Read , understand and follow all instructions inthe m...
Page 5 - Driving on slopes; Children safety
5 Never operate the mower without the entiregrass catcher or discharge chute in place. Slow down before turning. Never leave the machine unattended when theengine is running. Always turn off the blades, setthe parking brake, stop the engine and take outthe keys before leaving the machine. Stop the b...
Page 6 - Transportation; DANGER
6 Never operate the machine without properguards, covers, safety switches and devices inplace and properly functioning. Inspect theseitems regularly. If their condition or operation isquestionable they must be replaced beforeusing the machine. FIG - 2 Keep machine free of grass, leaves and otherdebr...
Page 7 - PRESENTATION; Presentation
7 PRESENTATION FUEL CAP MOTION CONTROLLEVERS PARKINGBRAKE DECK LIFTLEVER FOOTPLATE KEY SWITCH BLADEENGAGEMENTSWITCH THROTTLE Presentation Thank you for buying a YAZOO/KEES! Before operating your new mower, read, understandand follow the safety instructions and otherdirections in this manual. Lawnmow...
Page 8 - SETUP AND ADJUSTMENTS; Setup
8 SETUP AND ADJUSTMENTS WARNING: No settings or adjustments areto be made unless: Engine is stopped, keyhas been removed, park brake is on andbattery cable removed from battery. Setup Uncrate machine. Mount rear drive wheels using the lug nutsinstalled on the hubs. Check the tire pressure in all fou...
Page 11 - OPERATING INSTRUCTIONS; Operating instructions
11 Run engine full throttle to make sure wheels donot rotate. Readjust if any rotation occurs. Repeat the whole process for the opposite sideand tighten the nuts against the ball joints. Turn machine off. Reinstall the seat rod and check the wiringharness to the seat safety switch for a goodconnecti...
Page 13 - Maintenance; MAINTENANCE
13 Fuel shut off valve is located at the right rear ofthe seat. The valve has three positions a righttank, left tank and center is the off position. FIG -13. NOTE: EFI models the left position is the offposition. Pump release valves located at the right frontcorner of the pumps. Used to release thes...
Page 14 - ONLY USE
14 Hardware Check daily. Inspect the entire machine forloose or missing hardware. Air filter See engine manufacturers specifications forcleaning and replacement intervals. Hydraulic system Check oil level in tank daily. Oil level should be3/4” to 1” below the top of the tank. Check allfittings, hose...
Page 17 - Maintenance Schedule; For ZTH Riders
17 Maintenance Schedule For ZTH Riders Maintenance Maintenance Interval (hours)Daily 25 50 100 200 250 500 Engine (4) Check oil level X Change oil and filter (1) X Clean the air filter’s (3) X Replace air filter’s (3) X Check for fuel and oil leakage X Clean cooling flanges (3) X Check cooling air i...
Page 18 - TROUBLE SHOOTING; PROBLEM
18 TROUBLE SHOOTING PROBLEM POSSIBLE CAUSES ENGINE WILL NOT START. Blade switch on.Drive levers not in the neutral slots.Operator not in seat.Park brake disengaged.Dead battery.Fuel valve closed or in the wrong position.No fuel.Spark plugs defective.Spark plug wires off. MACHINE WILL NOT MOVE OR MOV...
Page 19 - WIRING DIAGRAMS; CONSOLE HARNESS
19 WIRING DIAGRAMS CONSOLE HARNESS Frame Harness Engine Clutch Left Motion Control Hour Meter Blade Switch Seat S tarter Switch Right Motion Control P/N 104414
Page 21 - FRAME HARNESS
21 FRAME HARNESS WIRING DIAGRAMS Clutch Engine Pigtail Ground to Engine S tarter Solenoid Park Brake Console Harness Brake Relay S tart Relay Run Relay P/N 104964
Page 23 - EFI HARNESS