Page 2 - PRINTED IN USA 2 MANUAL NO. 102936IR
PRINTED IN USA 2 MANUAL NO. 102936IR Congratulations on the purchase of your Kees mower. This manual has been prepared forthe owners and operators of the ZT MAX™ 52" and 61" commercial mowers. Read, under-stand and follow the saftey and operating instructions. ! WARNING Failure to follow cau...
Page 3 - PRINTED IN USA; TABLE OF CONTENTS
3 MANUAL NO. 102936IR PRINTED IN USA TABLE OF CONTENTS SAFETY:1. Training2. Preparation3. Operation4. Transportation5. Maintenance SETUP AND ADJUSTMENTS:1. Park brake2. Cutting height3. Mower deck leveling4. Mule drive belt tension5.Throttle lever tension6. Reverse spring detent adjustment7. Motion ...
Page 4 - PRINTED IN USA 4 MANUAL NO. 102936IR; SAFETY
PRINTED IN USA 4 MANUAL NO. 102936IR SAFETY TRAINING:1. Read this manual carefully and question your dealer if something is not clear.2. Be thoroughly familiar with the controls and proper use of the equipment.3. Never allow children, teenagers, or people unfamiliar with these instructions to use th...
Page 5 - Figure 1
5 MANUAL NO. 102936IR PRINTED IN USA SAFETY TRANSPORTATION:Use a heavy duty trailer to haul mower. Set park brake, turn off fuel valve and strap mower totrailer. NOTE: Park brake will not hold mower in place when transporting. Be sure to tie downthe mower to the trailer. Always back onto the trailer...
Page 6 - PRINTED IN USA 6 MANUAL NO. 102936IR; ADJUSTMENTS
PRINTED IN USA 6 MANUAL NO. 102936IR ADJUSTMENTS PARK BRAKE:1. Stop engine and remove key. Release park brake and measure the length of the spring.The distance between the washers on each end of the spring should be 2-7/8" (See Fig 2 ).2. If adjustment is needed, loosen the nut below the spring....
Page 7 - Figure 3
7 MANUAL NO. 102936IR PRINTED IN USA ADJUSTMENTS MULE DRIVE BELT TENSION:1. Stop engine and remove the key.2. Check to make sure the bolt head in the spring loaded idler pulley, on the left side of theengine deck is positioned between the two alignment holes in the left support plate(See Fig 4).3. I...
Page 8 - PRINTED IN USA 8 MANUAL NO. 102936IR; Figure 5A
PRINTED IN USA 8 MANUAL NO. 102936IR Figure 5A Figure 5B 5. If adjustment is necessary, loosen the nut against the yoke. Apply slight rearward pressureto the motion control lever and turn the head of the adjustment bolt in the proper direction untilthe lever is centered in the neutral slot. NOTE: if...
Page 10 - PRINTED IN USA 10 MANUAL NO. 102936IR; OPERATING INSTRUCTIONS
PRINTED IN USA 10 MANUAL NO. 102936IR OPERATING INSTRUCTIONS NOTE: To begin motion the operator must be in the seat and the brake disengaged before thelevers can be moved from the neutral slots or the engine will kill. By moving the levers an equal amount forward or back the mower will move in a str...
Page 11 - Figure 6
11 MANUAL NO. 102936IR PRINTED IN USA OPERATING INSTRUCTIONS STARTING AND OPERATION:1. Operator must be sitting in the seat. Engage park brake, blades off and place the motioncontrol levers in the neutral slots. (See figure 6)2. Adjust throttle to 1/2 and set choke (if needed) turn key and release a...
Page 12 - PRINTED IN USA 12 MANUAL NO. 102936IR; MAINTENANCE; (Clean grease zerk thoroughly before greasing)
PRINTED IN USA 12 MANUAL NO. 102936IR MAINTENANCE 7. Engine oil: Change oil to manufacturers specifications. Stop engine and remove key. Drainoil when engine is warm. Thoroughly clean around cap before removing. Remove oildrain cap from the end of drain hose located at the right rear of unit allow t...
Page 14 - PRINTED IN USA 14 MANUAL NO. 102936IR
Page 15 - TROUBLE SHOOTING
15 MANUAL NO. 102936IR PRINTED IN USA TROUBLE SHOOTING PROBLEM POSSIBLE CAUSES Engine won’t start Mower will not move or moves slowly or hard 1. Blade switch on.2. Drive levers not in the neutral slots.3. Operator not in seat.4. Park brake disengaged.5. Dead battery or cable off.....(Ignition switch...
Page 16 - PRINTED IN USA 16 MANUAL NO. 102936IR; WIRING DIAGRAM
PRINTED IN USA 16 MANUAL NO. 102936IR WIRING DIAGRAM
Page 17 - SERVICE RECORD; DESCRIPTION OF WORK DONE
17 MANUAL NO. 102936IR PRINTED IN USA SERVICE RECORD DESCRIPTION OF WORK DONE DATE SERVICE DONE BY
Page 18 - PRINTED IN USA 18 MANUAL NO. 102936IR