Yazoo/Kees KKFW48180, KKFW52180, KKFW52210 - Manuals

Page 2 - Congratulations; on the purchase of your

2 WARNING Continuous dedication to improve our products require that specifications and design are sub-ject to change without notice. WARNING THE ENGINE EXHAUST FROM THIS PRODUCT CONTAINS CHEMICALS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER, BIRTH DEFECTS OR OTHER REPRODUCTIVE HARM. ! Congratu...

Page 3 - TABLE OF CONTENTS; PAGE

3 TABLE OF CONTENTS SAFETY: ...................................................................... 4 Decals ..................................................................... 4Training .................................................................... 5Preparation .................................

Page 4 - SAFETY DECALS

4 EXPLOSION HAZARD CHEMICAL BURN HAZARD OPEN FLAME KEEP AWAY FROM SHUT OFF ENGINE ANDREMOVE KEY BEFORE MAINTENANCE OR REPAIR PERFOMORMING ANY ENGINE IS RUNING SAFETY SHIELDS WHILE DO NOT OPEN OR REMOVE STAY A SAFE DISTANCE FROM THE MACHINE READ OPERATORS RISK OF SEVERING OF TOES OR FINGERS RISK OF H...

Page 5 - SAFETY; footwear and long pants.; Do not; mow excessively steep slopes; ( mower may tip over and cause; shields, and safety devices in place and in proper working order.

5 SAFETY TRAINING: 1. Read this manual carefully and question your dealer if something is not clear.2. Be thoroughly familiar with the controls and proper use of the equipment.3. Never allow children, teenagers, or people unfamiliar with these instructions to use the mower. 4. Do not mow while peopl...

Page 6 - Turn off fuel valve and strap mower to trailer.

6 SAFETY TRANSPORTATION: Turn off fuel valve and strap mower to trailer. MAINTENANCE: 1. Keep all nuts, bolts and screws tight to keep mower in safe operating condition.2. Engine maintenance should comply with engine manufactures specifications. See the en- gine manual for specifications. 3. Never s...

Page 8 - FIGURE 2; MOTION CONTROL ADJUSTMENT

8 CONTROL LEVER THUMB LATCH SHORT LINKAGE MOTION CONTROL LINKAGE ADJUSTING NUTS FIGURE 2 MOTION CONTROL ADJUSTMENT 1. This adjustment must be made with the drive wheels rotating. Raise rear of the unit and block it up so the wheels are free to rotate. CAUTION: keep hands, feet and clothing awayfrom ...

Page 9 - REVERSE SPRING DETENT ADJUSTMENT; FIGURE 3; GROUND SPEED

9 REVERSE SPRING DETENT ADJUSTMENT 1. To check if your reverse spring detent adjustment is set right. Make sure your ground speed lever is pulled back to the neutral position. Release the thumb latchs(both sides) and pull upon the control levers at the same time. Then release the levers, it should r...

Page 10 - FIGURE 4; DECK BELT; Position mower on a flat surface and stop engine.

10 ADJUSTMENTS FRONT DECK BELT ROUTING: FIGURE 4 DECK BELT FIXED IDLERPULLEY (TALL) RIGHT DECKPULLEY SPRING FIXED IDLERPULLEY CENTER DECKPULLEY SPRING LOADEDIDLER ARM ELECTRIC CLUTCHON THE ENGINE LEFT DECKPULLEY MOWER DECK LEVELING: 1. Position mower on a flat surface and stop engine. 2. Check the t...

Page 12 - OPERATING INSTRUCTIONS; FIGURE 5

12 OPERATING INSTRUCTIONS CONTROLS: Be thoroughly familiar with all controls their function and how to operate them before operatingthe mower. 1. Control levers: Located on each side of the handle control direction of movement. The left lever controls the flow of oil from the left hydro pump to the ...

Page 13 - Once the engine is running adjust the throttle.

13 OPERATING INSTRUCTIONS STARTING AND OPERATION:1. Making sure the blades are disengaged, ground speed lever in neutral, the thumb latches locked, and the fuel valve on. 2. Adjust throttle to choke (if needed) turn key to start position, until engine starts. 3. Once the engine is running adjust the...

Page 14 - MAINTENANCE; oil when engine is warm.; Thoroughly clean around cap before removing.; Remove oil; Thoroughly; Remove cap. Oil level should be

14 MAINTENANCE 1. Engine oil level: Check daily with engine cold and on a flat surface. Remove the dipstick and wipe clean. Reinsert the dipstick all the way,but do not screw down. Remove the dipstick andcheck oil level. If oil level is low add oil. Use engine manufacturers specs for type of oil. 2....

Page 16 - FIGURE 6

16 CUTTER HOUSING SPINDLEASSEMBLYS The cutter housing assembly is designed with aslip fit inner race and pulley. The sole purposeof the setscrew in the pulley is to hold thehousing assembly together. The setscrew isnot ment to secure the pulley. The pulley issecured by pinching the pulley to the inn...

Page 18 - SERVICE RECORD; DESCRIPTION OF WORK DONE

18 SERVICE RECORD DESCRIPTION OF WORK DONE DATE SERVICE DONE BY