Yazoo/Kees KHKW36151, KHKW48171 - Manuals

Page 2 - Congratulations; on the purchase of your

2 WARNING Continuous dedication to improve our products require that specifications and design aresubject to change without notice. WARNING THE ENGINE EXHAUST FROM THIS PRODUCT CONTAINS CHEMICALS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER, BIRTH DEFECTS OR OTHER REPRODUCTIVE HARM. ! Congratula...

Page 4 - mow excessively steep slopes; ( mower may tip over and cause; Use caution when backing up.

4 SAFETY TRAINING: 1. Read this manual carefully and question your dealer if something is not clear.2. Be thoroughly familiar with the controls and proper use of the equipment.3. Never allow children, teenagers, or people unfamiliar with these instructions to use themower.4. Do not mow while people,...

Page 5 - SAFETY; Turn off fuel valve and strap mower to trailer.; EQUIPMENT SETUP AND ADJUSTMENTS

5 SAFETY TRANSPORTATION: Turn off fuel valve and strap mower to trailer. MAINTENANCE: 1. Keep all nuts, bolts and screws tight to keep mower in safe operating condition.2. Engine maintenance should comply with engine manufactures specifications. See the enginemanual for specifications.3. Never store...

Page 7 - CUTTING HEIGHT ADJUSTMENT CHART; MOTION CONTROL ADJUSTMENT

7 CUTTING HEIGHT ADJUSTMENT CHART Note: To quickly achive small changes in cutting heights, move the spacers from under the cutter housing to above the cutter pulley. (Each spacer moved will give an additional 1/4" of cutting height ). USE ONLY 4 BLADE SPACERS MAXIMUM AXLE POSITION NUMBER OF SPA...

Page 8 - REVERSE SPRING DETENT ADJUSTMENT

8 Figure 4 (Right side cut away view of console.) Figure 3 REVERSE SPRING DETENT ADJUSTMENT 1. To check if your reverse spring detent adjustment is set right. Make sure your ground speedlever is pulled back to the neutral position. Release the thumb latchs(both sides) and pull up on thecontrol lever...

Page 9 - Figure 5; BLADE DRIVE BELT ADJUSTMENT

9 Figure 5 AUXILARY BELT ADJUSTMENT ROD IDLER PIVOT POINT TURNBUCKLE ENGAGEMENT IDLER ASSEMBLY 1/4" BLADE DRIVE BELT ADJUSTMENT 1. Before performing adjustments on blade belt, turn the mower off and disconnect spark plug wireor wires.2. Remove front deck belt shield.3. Loosen nut on turnbuckle.4...

Page 10 - ENGINE BELT GUIDES; Figure 6; PUMP BELT

10 ENGINE BELT GUIDES 1. Before performing adjustments on belt guides, turn the mower off and disconnect spark plug wireor wires.2. Belt guides under the engine should be adjusted as shown in figure 6. Figure 6 PUMP BELT 1. Before performing adjustments on pump belt, turn the mower off and disconnec...

Page 11 - OPERATING INSTRUCTIONS

11 OPERATING INSTRUCTIONS CONTROLS: 1. Be thoroughly familiar with all controls their function and how to operate them beforeoperating the mower. 2. Control levers: Located on each side of the handle control direction of movement. The left levercontrols the flow of oil from the left hydro pump to th...

Page 13 - Remove oil; Thoroughly; Remove cap. Oil level should be

13 MAINTENANCE 5. Hardware: Stop engine and remove key thoroughly inspect the entire machine for anymissing or loose hardware. Check daily. 6. Air cleaner: Stop engine and remove key. Remove plastic cover and loosen wingnut on theair cleaner. Remove the foam pre-cleaner and wash or replace if needed...

Page 14 - Figure 7

14 CUTTER HOUSING SPINDLEASSEMBLYS The cutter housing assembly is designed with aslip fit inner race and pulley. The sole purposeof the setscrew in the pulley is to hold thehousing assembly together. The setscrew isnot ment to secure the pulley. The pulley issecured by pinching the pulley to the inn...

Page 16 - SERVICE RECORD; DESCRIPTION OF WORK DONE

16 SERVICE RECORD DESCRIPTION OF WORK DONE DATE SERVICE DONE BY