Yard-man 203 - Manuals - manualsarea.com

Page 3 - SECTION 1: IMPORTANT SAFE OPERATION PRACTICES; DANGER; TRAINING

3 SECTION 1: IMPORTANT SAFE OPERATION PRACTICES WARNING: This symbol points out important safety instructions which, if not followed, could endanger the personal safety and/or property of yourself and others. Read and follow all instructions in this manual before attempting to operate this machine. ...

Page 5 - SECTION 2: ASSEMBLING YOUR CHIPPER SHREDDER VACUUM; Removing Unit From Carton

5 WARNING: - YOUR RESPONSIBILITY: Restrict the use of this power machine to persons who read,understand and follow the warnings and instructions in this manual and on the machine. NOTE: Not all safety labels shown may apply to your chipper shredder vacuum. SECTION 2: ASSEMBLING YOUR CHIPPER SHREDDER...

Page 6 - Attaching The Nozzle; Attaching The Bag; SECTION 3: KNOW YOUR CHIPPER SHREDDER VACUUM

6 Attaching The Nozzle • Remove three wing nuts from the front of the chipper shredder vacuum. • Place nozzle in position over the three studs on unit and secure with wing nuts just removed.See Figure 2. Figure 2 NOTE: The metal tab on the nozzle must depress thesafety switch button attached to the ...

Page 7 - SECTION 4: OPERATING YOUR CHIPPER SHREDDER VACUUM; Starting Engine

7 Starter Handle (Not Shown) The starter handle is located on the engine. Pull the starter handle to start engine. Engine Controls See the separate engine manual for the location and function of the controls on the engine. Figure 5 SECTION 4: OPERATING YOUR CHIPPER SHREDDER VACUUM WARNING: Read, und...

Page 8 - SECTION 5: ADJUSTING YOUR CHIPPER SHREDDER VACUUM

8 • Pull rope with a rapid, continuous, full arm stroke. Keep a firm grip on starter handle. Let rope rewind slowly. • Repeat the previous steps until engine fires. When engine starts, move choke control (if equipped) gradually to RUN position. WARNING: Keep bystanders, helpers,pets, and children at...

Page 9 - Nozzle Door Height Adjustment; Drive Clutch Cable Adjustment; Engine Adjustments; SECTION 6: MAINTAINING YOUR CHIPPER SHREDDER VACUUM; Lubrication

9 Figure 7 Nozzle Door Height Adjustment The nozzle adjustment levers are located on each side of the nozzle door. The nozzle door can be adjusted to any of five positions, ranging from 1/2” to 3” ground clearance that will provide the best performance for the operating conditions. Slide the height ...

Page 10 - Maintenance; Removing The Flail Screen; Customer Responsibilities

10 Maintenance Engine Refer to the separate engine manual for all engine maintenance instructions. • Check engine oil level before each use as instructed in the separate engine manual packed with your unit. Read and follow instructions carefully. • Clean air cleaner every 25 hours under normal condi...

Page 13 - Storing Your Chipper Shredder Vacuum; SECTION 7: TROUBLESHOOTING

13 Storing Your Chipper Shredder Vacuum • Clean the equipment thoroughly. • Wipe equipment with an oiled rag to prevent rust. • Refer to engine manual for correct engine storage instructions • Store unit in a clean, dry area. Do not store next to corrosive materials such as fertilizer. WARNING: Neve...

Page 14 - SECTION 8: PARTS LIST FOR MODEL 203

14 SECTION 8: PARTS LIST FOR MODEL 203 1 2 2 3 3 4 5 6 7 8 8 9 10 11 12 9 10 13 13 14 14 15 16 REF. NO. PART NO. DESCRIPTION 1 681-0095 Chipper Chute 2 712-3010 Hex Nut 5/16-18 3 736-0242 Bell Washer.340 ID x.872 OD 4 731-1690A Discharge Chute 5 764-04001 Bag 6 631-0069 Nozzle Assembly 7 731-1831 No...

Page 20 - MANUFACTURER’S LIMITED WARRANTY FOR:

MANUFACTURER’S LIMITED WARRANTY FOR: The limited warranty set forth below is given by MTD LLC with respect to new merchandise purchased and used in the United States, its possessions and territories. “MTD” warrants this product against defects in material and workmanship for a period of two (2) year...