Page 2 - IMPORTANT SAFETY INFORMATION; GENERAL SAFETY WARNINGS; for future reference.; SAFETY; Read and understand all instructions.; Unauthorized modification may impair the function and/or; Use the right tool for the job.
IMPORTANT SAFETY INFORMATION GENERAL SAFETY WARNINGS Read all safety warnings and instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. SAFETY The warnings, precautions, and ins...
Page 3 - IMPORTANT; bonding and other general wiring procedures.; NOTE; Hair can become entangled in suction outlet cover.; Body Suction Entrapment-; unsecured can result in evisceration/disembowelment.; Mechanical Entrapment-; There is potential for jewelry
IMPORTANT SAFETY INFORMATION 2 To reduce the risk of electric shock replace damaged cord immediately. Do NOT bury cord. Locate cord to prevent abuse from lawn mowers, hedge trimmers and other equipment.Risk of Electric Shock. Connect only to a branch circuit protected by a ground-fault circuit-inter...
Page 4 - Do not; All suction and discharge valves; MUST be OPEN; when starting the circulation; Fire and Burn Hazard:; minimize the risk for burns.
3 IMPORTANT SAFETY INFORMATION Hazardous Pressure: Pool and spa water circulation systems operate under hazardous pressure during start-up, normal operation, and after pump shut-off. Stand clear of circulation system equipment during pump start-up. Failure to follow safety and operation instructions...
Page 5 - DIAGRAM AND SPECIFICATIONS; FEATURES AND SPECIFICATIONS
4 DIAGRAM AND SPECIFICATIONS PUMP HOUSING PUMP HOUSING PUMP COVER & GASKET MOTOR MOUNTING FOOT STRAINER COVER TRAINER HOUSING STRAINER BASKET FEATURES AND SPECIFICATIONS Compatible with DE, sand, and cartridge filter Assembled Product Dimensions (L x W x H) 24.0 x 9.0 x 12.0 Inches Self-priming ...
Page 6 - INSTALLATION; PIPE SIZING CHART; between the pump suction inlet and any plumbing fittings.; PUMP LOCATION; the end of the fitting.; using Teflon tape as friction is reduced considerably; DO NOT; over-tighten fitting or you may cause; PUMP MOUNTING; Be protected from excess moisture and flooding.
5 INSTALLATION PIPE SIZING CHART NOTE : It is recommended that a minimum length of piping, equivalent to 10 pipe diameters, be used between the pump suction inlet and any plumbing fittings. Fasten pump to base or pad with screws or bolts to reduce vibration and stress on pipe or hose joints. We reco...
Page 7 - SPECIFICATIONS
6 SPECIFICATIONS Risk of Electric Shock. All electrical wiring MUST be in conformance with applicable local codes, regulations, and the National Electric Code (NEC). All electrical wiring should be performed by a qualified professional. Hazardous voltage can shock, burn, and cause death or serious p...
Page 8 - START-UP AND OPERATION; Before removing strainer cover:; from pump and piping system using filter manual air relief valve.
7 START-UP AND OPERATION PRIOR TO START-UP Notice: It is necessary to perform a pressure test prior to initial use to ensure pump is functioning properly. The following criteria should be maintained for this test: 1. Have a professional perform this test. 2. Ensure all pump and system components are...
Page 9 - OPERATION; PUMP WINTERIZATION STORAGE; cover or wrap pump with plastic film or bags.; START-UP FOR WINTERIZED EQUIPMENT
8 OPERATION PUMP WINTERIZATION STORAGE ELECTRICAL HAZARD: To avoid dangerous or fatal electrical shock hazard, turn OFF power to motor before draining pump. Drain all water from pump and piping when expecting freezing temperatures or when storing pump. 1. Drain water level below all inlets to the po...
Page 10 - SHAFT SEAL CHANGE INSTRUCTIONS
OPERATION 1. Shut off water flow to pump by closing appropriate valves or by plugging both the skimmer outlet port and return port to pool. Disconnect piping or hoses from the motor/ pump assembly. 2. Remove the strainer by disengaging and removing the strainer cover. Remove the basket. Lift up on s...
Page 11 - TROUBLESHOOTING
Page 12 - MAINTENANCE
11 MAINTENANCE Clean strainer basket regularly. Do NOT strike basket to clean. Inspect strainer cover gasket regularly and replace as necessary. Keep motor clean. Insure air vents are free from obstruction.Occasionally, shaft seals must be replaced, due to wear or damage.
Page 13 - OF REPLACEMENT PARTS THERETO.; Record Product’s Serial Number Here:; as replacement parts.; PLEASE READ THE FOLLOWING CAREFULLY
12 THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR TH...
