Whirlpool XCGM2765FQ0 - Manuals

8 DIMENSIONS/CLEARANCES Side View Back View Dimensions Clearances 29 1 / 4 " ( 743 mm ) 35" (889 mm) 8 1 / 4 " ( 210 mm ) 1" ( 25 mm ) 26" (660 mm) 3 1 / 4 " ( 83 mm ) 7 1 / 2 " ( 191 mm ) 0" (0 mm) 0" (0 mm) 15" (381 mm) 14" max (356 mm) 0" (0 mm) 1 1...

9 Your dryer can be installed in a basement, laundry room, or recessed area.This dryer is not intended for installation in a mobile home.Companion appliance location requirements should also be considered. IMPORTANT: Do not install or store the dryer where it will be exposed to water and/or the weat...

10 INSTALLING LEVELING LEGS 1. Prepare dryer for leveling legsNOTE: Slide dryer onto cardboard or hardboard before moving to avoid damaging floor covering. Using two or more people, move dryer to desired installation location. Take tape off front corners of dryer. Open dryer and remove the literatur...

11 LEVELING 2. Grip dryer from top and rock back and forth, making sure all four legs are firmly on floor. Repeat, rocking dryer from side to side. If dryer rocks, go to Step 3 and adjust leveling legs. 3. If dryer is not level, use a 1" or 25 mm open-end or adjustable wrench to turn the levelin...

12 ELECTRIC DRYER INSTALLATION REQUIREMENTS Electrical Requirements This is 3-wire appliance which must be earthed.Do not earth to a gas pipe.Failure to follow these instructions could result in death, fire, or serious injury. Electric Shock Hazard This dryer is supplied without an electric cord and...

13 GAS DRYER INSTALLATION REQUIREMENTS Electrical Requirements EARTHING INSTRUCTIONS SAVE THESE INSTRUCTIONS IMPORTANT: Observe all governing codes and ordinances. You will need a grounded electrical outlet located within 610 mm (2 feet) of either side of the dryer. This dryer is supplied/fitted wit...

15 DRYER VENTING REQUIREMENTS WARNING: To reduce the risk of fire, this dryer MUST BE EXHAUSTED OUTDOORS. IMPORTANT: Observe all governing codes and ordinances. In Australia and New Zealand, refer to AS/NZS 5601.1 – Gas Installations. Dryer exhaust must not be connected into any gas vent, chimney, w...

16 102 mm (4") Diameter Exhaust Hoods Box Hood Louvered Hood Angled Hood Vent Hoods DRYER VENTING REQUIREMENTS Exhaust hood must be at least 305 mm (12") from the ground or any object that may be in the path of the exhaust (such as flowers, rocks, bushes, or snow). Maximum Vent Length/Vent C...

17 DRYER VENTING REQUIREMENTS 1. Connect gas supply to dryer. If the flexible gas hose has 10 mm (3/8") BSP thread, use the supplied conversion thread adapter. Use pipe-joint compound resistant to the action of L.P. gas for gas connections.If necessary for service, open the toe panel. Use a putt...

18 TECHNICAL SPECIFICATIONS – GAS DRYER 220–240V~50Hz 1ph 3A max. IP24 Clothes capacity: 9.0 kg max. Sound pressure level, Lpa: 58 dBA (uncertainty, Kpa: +/-10 dBA) Total mass: 68 kg max. Country: CH, CZ, CY, ES, GB, GR, HR, IE, IT, PT, SI, SK, TR CY, CZ, DK, EE, FI, GR, HU, IT, NO, RO, SE, SK, TR E...

19 1. Check the electrical requirements. Be sure that you have the correct electrical supply and the recommended earthing method. See “Electrical Requirements.” 2. Check that all parts are now installed. If there is an extra part, go back through the steps. 3. Check that you have all of your tools. ...

20 REVERSING DRYER DOOR SWING (OPTIONAL) 9. Attach door hinges to dryer door so that larger hole is at the bottom of the hinge and the hinge pin is toward the door front. 10. Remove the 4 screws that attach 2 plugs on the left side. Attach plugs to right side using the same 4 screws. 11. Insert scre...

21 MODEL NOMENCLATURE:CGM – Whirlpool Gas FQ – Series Revision CEM – Whirlpool Electric 2765 – Model Type Number DRYER DISPOSAL