Page 2 - INSTALLATION REQUIREMENTS; Tools and Parts; Tools Needed
2 BUILT-IN OVEN SAFETY INSTALLATION REQUIREMENTS Tools and Parts Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here. Tools Needed ■ Phillips screwdriver ■ Measuring tape ■ Hand or electric drill (for wall cabinet ins...
Page 3 - Location Requirements; Product Dimensions - Single Ovens
3 Location Requirements IMPORTANT: Observe all governing codes and ordinances. ■ Cabinet opening dimensions that are shown must be used. Given dimensions provide minimum clearance with oven. ■ Recessed installation area must provide complete enclosure around the recessed portion of the oven. ■ Groun...
Page 4 - Cabinet Dimensions - Single Ovens
4 Cabinet Dimensions - Single Ovens Single Oven Undercounter (Without Cooktop Installed Above) Single Ovens Installed in Cabinet * NOTE: The cutout height can be between 26 15 / 16 " and 29 7 / 16 " (68.4 cm and 74.8 cm) for single ovens. A B C D E 27" (68.6 cm) models A. 27" (68.6 c...
Page 6 - Electrical Requirements; Electrical Connection
6 Electrical Requirements If codes permit and a separate ground wire is used, it is recommended that a qualified electrical installer determine that the ground path and the wire gauge are in accordance with local codes.Check with a qualified electrical installer if you are not sure the oven is prope...
Page 7 - INSTALLATION INSTRUCTIONS; Prepare Built-In Oven; WARNING
7 INSTALLATION INSTRUCTIONS Prepare Built-In Oven 1. Decide on the final location for the oven. Avoid drilling or cutting into house wiring during installation. 2. To avoid floor damage, set the oven onto cardboard prior to installation. Do not use handle or any portion of the front frame for liftin...
Page 8 - Positioning Oven Feet for Multiple; Single Ovens
8 Replace Oven Door(s) 1. Using two hands, grasp side edges of door at the midpoint. Face the oven cavity. 2. Locate the slots on each side of the oven front frame for the door hinge locks. 3. Using two hands, grasp the edges of the oven door. At a 45° angle, insert the hinges at the same time, and ...
Page 11 - Cutout Height Is Between 50
11 Cutout Height Is Between 50 1 / 2 " and 51 1 / 8 " (128.2 cm and 129.9 cm) 1. Using two or more people, place the oven on its back on a covered surface. 2. Install a foot on the left rear spacer using a #8-18 x 3/8" (9.5 mm) screw. NOTE: Position the foot so the long side of the foot ...
Page 12 - Cutout Height Is Between 51
12 Cutout Height Is Between 51 3 / 16 " and 52 3 / 16 " (130 cm and 132.6 cm) 1. Using two or more people, place the oven on its back on a covered surface. 2. Install a foot on the left rear spacer using a #8-18 x 3/8" (9.5 mm) screw. NOTE: Position the foot so the short side of the foot...
Page 13 - Make Electrical Connection; For Double Ovens
13 Make Electrical Connection For Double Ovens For Single Ovens This oven is manufactured with a neutral (white) power supply wire and a cabinet-connected green (or bare) ground wire twisted together. 1. Disconnect power. 2. Feed the flexible conduit from the oven through the opening in the cabinet....
Page 14 - Install Oven
14 3-Wire Cable from Home Power Supply: U.S. Only IMPORTANT: Use the 3-wire cable from home power supply where local codes permit a 3-wire connection. 1. Connect the two black wires (C) together using a UL Listed wire connector. 2. Connect the two white wires (D) and the green (or bare) ground wire ...
Page 16 - Install Warming Drawer Deflector Kit; (Only for Ovens Installed Above Warming Drawers); Parts Supplied in Deflector Kit; Complete Installation; Check Operation of Single and Double Ovens
16 Install Warming Drawer Deflector Kit (Only for Ovens Installed Above Warming Drawers) On single and double oven models installed above a warming drawer, a warming drawer deflector kit must be installed. See the “Tools and Parts” section for information on ordering. Parts Supplied in Deflector Kit...