Whirlpool WED7500GC0 - Manuals

6 Mobile home - Additional installation requirements: This dryer is suitable for mobile home installations. The installation must conform to the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280 (formerly the Federal Standard for Mobile home construction and Safety, Title 2...

7 4-wire receptacle (14-30R) ELECTRIC DRYER POWER HOOKUP- CANADA ONLY ELECTRICAL REQUIREMENTS It is your responsibility: ■ To contact a qualified electrical installer. ■ To be sure that the electrical connection is adequate and in conformance with Canadian Electrical Code, C22.1-latest edition and a...

8 GAS TYPE Natural Gas: This dryer is equipped for use with Natural gas. It is design- certified by CSA International for LP (propane or butane) gases with appropriate conversion. ■ Your dryer must have the correct burner for the type of gas in your home. Burner information is located on the rating ...

9 3/8" NPT dryer pipe NOTE: For a garage installation, the gas pipe height must be an additional 18" (460 mm) from the floor. GAS SUPPLY CONNECTION REQUIREMENTS ■ Use an elbow and a 3/8" flare x 3/8" NPT adapter fitting between the flexible gas connector and the dryer gas pipe, as ne...

10 MAKE ELECTRICAL CONNECTION - U.S.A. ONLY (EFFECTUER LE RACCORDEMENT ÉLECTRIQUE – ÉTATS-UNIS SEULEMENT) ELECTRICAL CONNECTION Electrical Connection Options Power Supply Cord 1. Choose electrical connection type Power supply cord 4-wire receptacle (NEMA Type 14-30R): Go to Power Supply Cord Connect...

11 4-wire Power Supply Cord Connection IMPORTANT: A 4-wire connection is required for mobile homes and where local codes do not permit the use of 3-wire connections. Power supply cord 4-wire receptacle (NEMA Type 14-30R): Go to “4-Wire Power Supply Cord Connection”. Power supply cord 3-wire receptac...

12 3-wire receptacle (NEMA type 10-30R) 3-prong plug Spade terminals with upturned ends Ring terminals Use where local codes permit connecting cabinet-ground conductor to neutral wire. 3-wire Power Supply Cord Connection 3. Connect remaining wires Connect remaining wires to outer terminal block scre...

13 Put direct wire cable through the strain relief. The strain relief should have a tight fit with the dryer cabinet and be in a vertical position. Tighten strain relief screw against the direct wire cable. 2. Attach direct wire cable to strain relief 3-wire direct connection: Go to “3-Wire Direct C...

14 Place hooked ends of remaining direct wire cable wires under outer terminal block screws (hooks facing right). Squeeze hooked ends together and tighten screws. Finally, reinsert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw. Now, go to “Venting Requi...

15 1. Prepare to connect neutral ground wire and neutral wire B A E Remove center terminal block screw (B). Remove neutral ground wire (E) from external ground conductor screw (A). Optional 3-wire Connection You must verify with a qualified electrician that this grounding method is acceptable before...

16 VENTING REQUIREMENTS WARNING: To reduce the risk of fire, this dryer MUST BE EXHAUSTED OUTDOORS. IMPORTANT: Observe all governing codes and ordinances. Dryer exhaust must not be connected into any gas vent, chimney, wall, ceiling, attic, crawlspace, or a concealed space of a building. Only rigid ...

18 Special provisions for mobile homes: Exhaust vent must be securely fastened to a noncombustible portion of mobile home and must not terminate beneath the mobile home. Terminate exhaust vent outside. Moblie Home Exhaust installation Connect vent to exhaust hood 2. Vent must fit over the exhaust ho...

19 LEVEL DRYER Not Level LEVEL Not Level Check levelness of dryer from side to side. Repeat from front to back. NOTE: The dryer must be level for the moisture sensing system to operate correctly. CONNECT VENT 1. Connect vent to exhaust outlet Using a 4" (102 mm) clamp, connect vent to exhaust ou...

21 REVERSE DOOR SWING † ® TORX and T20 are registered trademarks of Acument Intellectual Properties, LLC. Place towel on dryer 1. Place towel on top of dryer to avoid damaging the surface. Remove screws attaching hinges to door. Remove screws from hinges 4. Lift door until top screws in dryer cabine...

23 Remove and transfer plugs 11. Remove the 4 screws that attach 2 plugs on the left side. Transfer plugs to opposite side using the same 4 screws. Insert screws in hinge holes on dryer cabinet 12. NOTE: 2 people may be needed to reinstall door. Insert screws into the bottom holes on left side of dr...