Whirlpool W10057363B - Manuals

5 Installation spacing for recessed area or closet installation All dimensions show recommended and minimum spacing allowed. Additional spacing should be considered for ease of installation ■ and servicing.Additional clearances might be required for wall, door, floor ■ moldings, and dryer venting.Ad...

6 Then choose a 4-wire power supply cord with ring or spade terminals and UL listed strain relief. The 4-wire power supply cord, at least 4 ft. (1.22 m) long, must have four 10-gauge copper wires and match a 4-wire receptacle of NEMA Type 14-30R. The ground wire (ground conductor) may be either gree...

7 For direct wire installations: ELECTRIC INSTALLATION For power supply cord installations: Remove hold-down screw and terminal block cover. 1. choose electrical connection type Power supply cord 4-wire receptacle (NEMA Type 14-30R). Go to Power Supply Cord Connection. 3-wire direct connection: Go t...

8 Power supply cord strain relief: 4-Wire Power Supply cord connection Power Supply Cord Connection 4-wire receptacle (NEMA type 14-30R) 4-prong plug Spade terminals with upturned ends Ring terminals ImPoRTAnT: A 4-wire connection is required for mobile homes and where local codes do not permit the ...

10 4-Wire Direct Wire connection Direct Wire Connection 1. Prepare your 4-wire cable for direct connection 1" (25 mm) 3 1 ⁄ 2 " (89 mm ) 5" (127 mm) 2. Prepare to connect neutral ground wire and neutral wire E B A 1. Attach direct wire strain relief C B A 2. Attach direct wire cable to s...

11 1. Prepare your 3-wire cable for direct connection 1" (25 mm) 3½" (89 mm) 2. Remove center screw B 5. connect remaining wires 4. connect ground wire F A Use where local codes permit connecting cabinet-ground conductor to neutral wire. Remove center terminal block screw (B). Direct wire ca...

12 Connect neutral ground wire (E) and neutral wire (white or center wire) (C) of power supply cord or cable under center, terminal block screw (B). Tighten screw. Place ends of remaining wires under outer terminal block screws. Tighten screws. Connect a separate copper ground wire (G) under the gre...

13 venting Requirements vENTINg WARnInG: To reduce the risk of fire, this dryer MUST BE EXHAUSTED OUTDOORS. ImPoRTAnT: Observe all governing codes and ordinances. Dryer exhaust must not be connected into any gas vent, chimney, wall, ceiling, attic, crawlspace, or a concealed space of a building. Onl...

14 Plan vent System choose your exhaust installation type Recommended exhaust installation: Vent System chart number of 90° elbows Type of vent Box/louvered hoods Angled hoods 1 4 3 2 0 Rigid metal Rigid metal Rigid metal Rigid metal Rigid metal 64 ft. (20 m) 54 ft. (16.5 m) 44 ft. (13.4 m) 35 ft. (...

15 Install vent System 1. Install exhaust hood 12" min. (305 mm) 12" min. (305 mm) 2. connect vent to exhaust hood Install exhaust hood and use caulking compound to seal exterior wall opening around exhaust hood. Vent must fit over the exhaust hood. Secure vent to exhaust hood with 4" (1...

17 CONNECT vENT 1. connect vent to exhaust outlet 2. move dryer to final location Using a 4" (102 mm) clamp, connect vent to exhaust outlet in dryer. If connecting to existing vent, make sure vent is clean. Dryer vent must fit over dryer exhaust outlet and inside exhaust hood. Check that vent is...

19 † ® TORX is a registered trademark of Saturn Fasteners, Inc. DOOR REvERSAL (OPTIONAL) The following instructions are for models with a round-shaped door. ImPoRTAnT: For models with a square shaped door, an additional kit is needed. Please contact your retailer, or see the For Assistance or Servic...

21 8. Reinstall hinge and latch on opposite sides Using a Torx ® T25 screwdriver, reinstall the latch plate, latch backing plate, and hinge assembly on the opposite sides from which they were removed. 6. Rotate and reassemble outer window assembly to trim ring With the edge with 2 notches at the top...