Whirlpool KD-11 - Manuals

2 1. Once the tub has filled with hot water the motor begins to rotate forcing the water up through the pump chamber and out through the spray arms. Two spray jets on the underside of the lowerspray arm direct water down onto the fine mesh screen of the pump housing to clear soils thatmay collect th...

3 COMPONENT LOCATION TIMER LATCH ASSEMBLY FILL VALVE MOTOR RELAY FLOAT SWITCH OPERATING THERMOSTAT (Attached to bottom of pump housing) HI LIMIT THERMOSTAT PUMP AND MOTOR ASSEMBLY HEATER DETERGENT AND RINSE AID DISPENSER ASSEMBLY PROGRAMSWITCHES INDICATOR LIGHTS Section Two COMPONENT ACCESS

4 Removing Access and Outer Door Panels 1. Loosen but do not remove the two (2) toe panel screws below the access panel. Remove and set aside the two (2) screws above the access panel. (Fig. 2-1) 2. Remove the access panel assembly by sliding it upward to clear the loosened screws. (Fig. 2-1) 3. Rem...

6 Servicing the Vertical Water Tube The vertical water tube in these models deliverswater to the spray arm mounted underneath theupper dish rack and a smaller spray arm mountedat the top of the dishwasher tub. (Fig. 2-3) If the pump and motor assembly must beremoved for servicing, the vertical water...

7 Removing the Pump Motor Assembly 1. Unscrew and remove the nozzle cap and remove the nozzle bearing and spray arm. (Fig. 2-7) 2. Disconnect the wiring harness from the motor harness plug. 3. Rubber clamps secure the pump and motor assembly to the tub. Rotate these inward 90°.(Fig. 2-8) 4. Remove t...

11 TROUBLESHOOTING GUIDE Model DU910PFG PRECAUTIONS TO BE OBSERVED WHILE TROUBLESHOOTING Always check wiring harness and connectors before initiating any test procedures. Disconnect electric power from the dishwasher before touching the printed circuit boards or re-seating wire connectors. Voltage c...

12 PROBLEM POSSIBLE CAUSES CORRECTION/TEST Dishwasher does not run orstops during a cycle Dishwasher will not fill Dishwasher will not drain Dishwasher will notdry dishes 1. Door is not latching properly. 2. Child lock is "ON". 3. Wash Cycle not set properly. 4. Household fuse blown or circu...

13 COMPONENT TESTING PRECAUTIONS TO BE OBSERVED WHILE DIAGNOSING PROBLEM COMPONENTS Disconnect electric power from the dishwasher. Voltage checks should be made by inserting meter probes beside the wires in the connector blocks with the electric power source onand the connector block plugged in. Res...

15 Wiring Diagram Cycle Timing Charts Model DU910PFG Section Four TECH TIPS

16 Strip Circuits (DU910PFG) 5. Heat Dry 4. Drain 3. Wash 1. Fill 2. Water Heat

17 Models DP920PFG, DU920PFG, GU940SCG, GU960SCG & GU980SCG WIRING DIAGRAM

19 Note 1: Pre-Wash Sense Interval Pressure switch contact closure at any time during this interval causes thecycle to jump to interval 37. Immediately. For the normal cycle, the heater is“off” during this interval. For the heavy and pots-n-pans cycles the heater is“on” during this interval. The pow...

20 1. The diagnostics test cycle starts at interval 11 and concludes at interval2. To initiate the diagnostics test cycle, press the following sequence ofkeys within 10 seconds: High Temp Wash, Air Dry, High Temp Wash, Air Dry or Power Scour, Air Dry, Power Scour, Air Dry The diagnostics test cycle ...

22 Removing Access and DoorPanels 1. Loosen but do not remove the two (2) toe panel screws below the access panel. Re-move and set aside the two (2) screws abovethe access panel. (Fig. 4-1) 2. Remove the access panel assembly by slid- ing it upward to clear the loosened screws.This access panel will...

23 4. Pull the bottom of the outer door panel out- ward and slide it down approximately ¼” to½”. The panel will then be free for removal.(Fig. 4-1, inset) Set the door panel aside; itwill be replaced with a new custom panel. 5. Remove the existing door insulation and dis- card. Installing Custom Pan...

26 INSTALLING THE FLOOR MOUNTING KIT KIT CONTENTS (P/N 4378968): 2 P/N 9743463 Brackets (Fig. 4-12) 1 P/N 4378974 Instruction Sheet INSTALLATION INSTRUCTIONS 1. Loosen the two (2) screws below the access panel and remove the two (2) screws above the accesspanel. (Fig. 4-13) 2. Carefully slide the ac...

27 WHIRLPOOL Dishwasher Warranty LENGTH OR WARRANTY FULL ONE-YEARWARRANTYFROM DATE OFPURCHASE LIMITED ONE-YEARWARRANTYSECOND YEARFROM DATE OFPURCHASE LIMITED FOUR-YEARWARRANTYSECOND THROUGHFIFTH YEAR FROMDATE OF PURCHASE FULL TWENTY-YEARWARRANTYFROM DATE OFPURCHASE FSP™ replacement parts and repair ...

29 SERIAL PLATE LOCATOR SERIAL NUMBER DESIGNATOR SERIAL NUMBER MANUFACTURING SITEF = Findlay, OH YEAR OF MANUFACTUREG = 1997H = 1998 WEEK OF MANUFACTURE18 = 18th Week PRODUCT SEQUENCE NUMBER F G 18 70352 MODEL NUMBER DESIGNATOR MANUFACTURING NUMBER MARKETING CHANNEL (if present) PRODUCT GROUPD = Dis...

30 CONTACT INFORMATION For Product Specifications and Warranty Information Sources: 1-800-874-4698 For Technical Assistance: 1-800-253-2870 For Service Manuals and other Service Literature: 1-800-851-4605 For Service Replacement Parts: 1-800-259-7278 For Safety Related Information: 1-800-541-5746