Whirlpool 4KWTW4605FW0 - Manuals

Page 2 - WASHER SAFETY; IMPORTANT SAFETY INSTRUCTIONS

2 WASHER SAFETY n Cleaning and user maintenance by children must be supervised. n Children should be supervised to ensure that they do not play with the appliance. n Children less than 3 years of age should be kept away from the appliance unless continuously supervised. n Before the washer is remove...

Page 3 - INSTALLATION REQUIREMENTS; Tools and Parts

3 Optional tools: Parts supplied: NOTE: All parts supplied for installation are in cardboard insert in the top of the washer. INSTALLATION REQUIREMENTS Tools and Parts Gather required tools and parts before starting installation. 4" min (102 mm) Wood block Adjustable or open-end wrench 14 mm ( 9...

Page 4 - Location Requirements; Specifications

4 You will need: n A water heater set to 49°C (120°F). n An earthed electrical outlet located within 1.2 m (4 ft) of power cord on back of washer. n Hot and cold water faucets located within 0.9 m (3 ft) of hot and cold water fill valves on washer, and water pressure of 138–690 kPa (20–100 psi). n A...

Page 5 - Electric Requirements; EARTHING INSTRUCTIONS; Drain System

5 Wall standpipe drain system Laundry tub drain system Minimum capacity: 76 L (20 gal.). IMPORTANT: n Top of laundry tub must be at least 990 mm (39") above floor; install no higher than 1.22 m (48") from bottom of washer. n To avoid siphoning, no more than 114 mm (4.5") of drain hose sh...

Page 6 - INSTALLATION INSTRUCTIONS; Move washer

6 INSTALLATION INSTRUCTIONS Before you start: Remove shipping materials. It is necessary to remove all shipping materials for proper operation and to avoid excessive noise from washer. Move washer to within 1.2 m (4 ft) of its final location; it must be in a fully upright position. NOTE: To avoid fl...

Page 7 - Connect Inlet Hoses; Remove drain hose form; Connect Drain Hose; Place drain hose in standpipe; Attach drain hose to drain port

7 Connect Inlet Hoses Washer must be connected to water faucets with new inlet hoses with flat washers (provided). Do not use old hoses. NOTE: Both hoses must be attached and have water flowing to inlet valves. If you are only connecting to a cold water faucet, you must use a Y-adapter (provided). F...

Page 9 - Level Washer; Check levelness of washer; Adjust leveling feet; Tighten leveling feet

9 Level Washer IMPORTANT: Level washer properly to reduce excess noise and vibration. Move the washer to its final location. Place a level on top edges of washer. Use side seam as a guide to check levelness of sides. Check levelness of front using lid, as shown. Rock washer back and forth to make su...

Page 10 - Select plug; Power Cord Installation; Assemble plug

10 Complete Installation Checklist q Check electrical requirements. Be sure you have correct electrical supply and recommended earthing method. q Check that all parts are now installed. If there is an extra part, go back through steps to see what was skipped. q Check that you have all of your tools....

Page 11 - ةلاسغلا بيكرت تاميلعت

ةلاسغلا بيكرت تاميلعت W10849505B )ةيلصلأا تاميلعتلا( تايوتحملا لودج 2 .....................................................................................ةلاسغلا ةملاس 3 .................................................................................. بيكرتلا تابلطتم 3 ...............................

Whirlpool 4KWTW4605FW0 - Manuals

Manuals:

Installation Manual Whirlpool 4KWTW4605FW0

Summary

Whirlpool Manuals