Weider WESY99490 - Manuals - manualsarea.com

Page 3 - Before You Begin

3 ASSEMBLED DIMENSIONS: Height: 77 in.Width: 80 in. Depth: 55 in. Low PulleyStation Foot Plate LegLever Press Arms Seat Backrest ButterflyArms Ab PulleyStation WeightStacks Leg PressLever Thank you for selecting the innovative and versatileWEIDER ¨ PRO 9935 Home Gym. The WEIDER ¨ PRO 9935 offers a u...

Page 4 - Assembly

4 Note: This introduction will save you moretime than it takes to read it! Identifying Parts To help you identify the small parts used in assem-bly, we have included a PART IDENTIFICATIONCHART located in the center of this manual. Placethe chart on the floor or work table and use it toquickly identi...

Page 5 - Frame Assembly

1. Before beginning, make sure that you have readand understood the information on page 4. Locate and open the parts bag labeled ÒFRAMEASSEMBLY.Ó See drawing 1a. Press a 2Ó Square Inner Cap (28) into each end of the Butterfly Base (4). Press two 2ÓSquare Inner Caps (28) into the Weight Base (5). Ins...

Page 10 - Arm Assembly

15 15. Attach each of the four Weight Guides (15) to the Weight Top Frame (66) with a 3/8Ó x 3 3/4Ó Bolt (59),a 3/8Ó Flat Washer (48), and a 3/8Ó Nylon Locknut(50). Important: Go back and fully tighten all NylonLocknuts used in steps 1 through 15. 10 16 48 59 59 15 48 15 50 50 17. Press a 1 3/4Ó Squ...

Page 11 - Cable Assembly

11 20. Wrap the Butterfly Cable (73) around a ÒVÓ-Pulley (27) in the direction shown. Attach the ÒVÓ-Pulley anda Large Cable Trap (32) to the bracket on the back of the Butterfly Upright (1) with a 3/8Ó x 2 1/2Ó Bolt (53) and a 3/8Ó Nylon Locknut (50). Make sure the Large Cable Trap is oriented as s...

Page 20 - Seat Assembly

20 Seat Assembly 50. Locate and open the parts bag labeled ÒSEATASSEMBLY.Ó Attach the Backrest (12) to the indicated holes in theButterfly Upright (1) with two 1/4Ó x 2 1/2Ó Bolts (79)and two 1/4Ó Flat Washers (71). 50 79 79 1 12 71 51. Insert a 1/4Ó x 2 1/2Ó Carriage Bolt (45) through the center ho...

Page 21 - Miscellaneous Assembly

21 Miscellaneous Assembly 52. Insert a 1/4Ó x 2 1/2Ó Carriage Bolt (45) through the center hole in a Seat Plate (65). Attach the Seat Plateto a Seat (13) with two 1/4Ó x 3/4Ó Bolts (49). Insert the 1/4Ó x 2 1/2Ó Carriage Bolt (45) into the indi-cated hole in the Butterfly Seat Frame (14) andsecure i...

Page 23 - Cable Diagrams

23 Cable Diagrams The Cable Diagrams below and on the next page show the proper routing of the Butterfly Cable (73), the AbCable (74), the Low Pulley Cable (75) and the Press Cable (72). The numbers show the correct route for eachCable. Make sure that the Cables are routed correctly, that the Pulley...

Page 25 - Adjustment

25 Adjusting the Leg Press Plate To adjust the position of the Leg Press Plate (55), pull outthe Lock Pin (91) and slide the Adjustment Tube (90)backwards or forwards in the bracket on the Leg PressLever (83). Line up one of the adjustment holes in theAdjustment Tube with the hole in the bracket and...

Page 26 - Trouble-shooting and Maintenance

26 Slack can be removed form the Press Cable (72) by mov-ing one or both of the ÒVÓ-Pulleys (27) on the PressCable. One ÒVÓ-Pulley (27) is attached to the small tube on thePress Upright (2). There are three free holes in the smalltube, and you can move the ÒVÓ-Pulley to any one of themto tighten the...

Page 27 - Weight Resistance Chart

27 The threaded ends on the Press Cable (72) and the AbCable (74) that are attached to the weight stacks can alsobe used to tighten the cables. To tighten the Ab Cable (74), remove the ÒUÓ-Bracket (97)from the Short Weight Tube (17) by removing the 5/16Ó x1 3/4Ó Bolt (96) and the 5/16Ó Nylon Locknut...

Page 29 - Part Identification ChartÐModel No. WESY99490

3/8" Nylon Locknut (50) 3/8" Nylon Jamnut (63) 5/16" Nylon Locknut (64) 1Ó Tap Screw (80) 3/8" x 2" Bolt (54) 1/4" Flat Washer (71) 5/16" x 1 3/4" Bolt (96) 3/8" Flat Washer (48) 1/4" x 3/4" Bolt (49) 1/4" x 2 1/2" Bolt (79) 3/8" x 1" Bolt ...

Page 31 - Part ListÑModel No. WESY99490

Note: Ò#Ó indicates a non-illustrated part. Specifications are subject to change without notice. Part ListÑModel No. WESY99490 R0999B Key No. Qty. Description Key No. Qty. Description 1 1 Butterfly Upright 2 1 Press Upright 3 1 Support Frame 4 1 Butterfly Base 5 1 Weight Base 6 1 Press Base 7 1 Pres...

Page 32 - Exploded DrawingÑModel No. WESY99490

46 57 57 59 59 24 50 24 46 78 56 60 59 87 62 52 50 87 64 64 25 63 24 89 92 92 95 64 64 30 30 43 51 89 80 25 24 54 62 63 50 24 25 50 88 24 60 63 25 24 92 92 89 87 64 71 79 68 50 24 57 22 57 50 24 67 58 81 69 50 24 47 74 65 49 45 71 79 71 79 12 71 79 99 64 27 32 62 48 50 64 92 97 21 19 89 28 28 28 28 ...