Weider WESY99300 - Manuals - manualsarea.com

Page 2 - TABLE OF CONTENTS; LIMITED WARRANTY

2 LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3BE...

Page 3 - IMPORTANT PRECAUTIONS

3 IMPORTANT PRECAUTIONS WARNING: To reduce the risk of serious injury, read the following important precau- tions before using the weight system. 1. Read all instructions in this manual and in the accompanying literature before using theweight system. 2. It is the responsibility of the owner to ensu...

Page 4 - BEFORE YOU BEGIN

4 ASSEMBLED DIMENSIONS:Height: 198 cmWidth: 165 cmDepth: 86 cm Low PulleyStation Foot Plate Press Arm Backrest Curl Pad AdjustmentKnob ButterflyArms WeightStack Leg Press Lever Thank you for selecting the innovative and versatileWEIDER ® PRO 9930 weight system. The WEIDER ® PRO 9930 offers a unique ...

Page 5 - ASSEMBLY

5 ASSEMBLY Make sure you have the following tools: • Two adjustable wrenches • One standard screwdriver • One phillips screwdriver • One rubber mallet • You will also need grease or petroleum jelly, a small amount of soapy water, and clear tape ormasking tape. Note: Assembly will be more convenient ...

Page 6 - Frame Assembly

6 1. Before beginning, make sure that you have readand understood the information on page 5. Locate and open the parts bag labelled “FRAMEASSEMBLY.” Press a 2” Square Inner Cap (38) into the ButterflyBase (61). Press two 2” Square Inner Caps into thePress Base (60). Insert four 5/16” x 2 1/2” Carria...

Page 9 - Arm Assembly

9 11. Press a 1 1/2” Square Inner Cap (79) into the Press Seat Frame (52). Slide the bracket on the lower end of the Press SeatFrame (52) onto the indicated 5/16” x 2 1/2” CarriageBolts (1) in the Press Base (60). Tighten two 5/16”Nylon Locknuts (2) onto the Bolts. Attach the Press Seat Frame (52) t...

Page 10 - Cable Assembly

14. Open the parts bag labelled “CABLE ASSEMBLY AND PULLEYS.” For cable identification and routingduring steps 14–32, refer to the CABLE DIAGRAMSand CABLE ID CHART on pages 19 and 20. Insert two 3/8” x 1” Bolts (15) into the welded bracketson the Left and Right Butterfly Arms (67, 68). Secureeach Bo...

Page 16 - Seat Assembly

16 Seat Assembly 34. Press four 3/4” Round Inner Caps (40) into the ends of the Pad Tubes (48). Insert the Pad Tubes (48) into the indicated holes inthe Leg Lever (49) and the Press Seat Frame (52).Slide Foam Pads (47) onto the ends of both PadTubes. 35. Insert a 1/4” x 2 1/2” Carriage Bolt (12) int...

Page 19 - CABLE DIAGRAMS

19 CABLE DIAGRAMS The cable diagrams below and on the next page show the proper routing of the Short Cable (71), the MediumCable (72), and the Long Cable (73). The numbers show the correct route for each Cable. Make sure that theCables are routed correctly, that the Pulleys move smoothly, and that t...

Page 21 - ADJUSTMENT

21 USING THE CURL PAD To use the Curl Pad (69), insert the Curl Post (70) into theSeat Brace (75) and secure the Curl Post at the desiredheight with the Adjustment Knob (45). ATTACHING THE LAT BAR OR NYLON STRAP TOTHE HIGH PULLEY STATION Attach the Lat Bar (50) to the Medium Cable (72) with aCable C...

Page 22 - TROUBLE-SHOOTING AND MAINTENANCE

22 Slack can be removed from the Long Cable (73) by relo-cating the indicated 3 1/2” Pulley (5) on the Press SeatFrame (52). To do this, remove the 3/8” Nylon Locknut(4), 3/8” Flat Washer (17), and 3/8” x 2 1/2” Bolt (6). Re-attach the Pulley at the second or third hole, as needed. TROUBLE-SHOOTING ...

Page 23 - WEIGHT RESISTANCE CHART; PLACE

23 High Arm Butterfly Curl/ Leg Raise Weight Pulley Press (lbs.) Low Pulley (lbs.) Plates (lbs.) (lbs.) (lbs.) Top 11 20 15 16 17 1 25 39 31 32 37 2 40 59 48 47 56 3 55 78 64 63 76 4 70 97 80 78 95 5 84 117 97 93 115 6 99 136 113 109 135 7 114 156 130 124 154 8 128 175 146 140 174 The chart below sh...

Page 24 - ORDERING REPLACEMENT PARTS

Part No. 173978 R0501APrinted in Canada © 2001 ICON Health & Fitness, Inc. ORDERING REPLACEMENT PARTS To order replacement parts, simply call our Customer Service Department toll-free at 1-888-936-4266, Mondaythrough Friday, 8 a.m. until 6:30 p.m. EST (excluding holidays). To help us assist you,...

Page 26 - PART IDENTIFICATION CHART–Model No. WESY99300

1/4" Flat Washer (11) 5/16" Flat Washer (19) 3/8" Flat Washer (17) 5/16" x 1 3/4" Bolt (9) 3/8" Nylon Locknut (4) 3/8" Jam Nut (18) 1/4" Nylon Locknut (16) #10 x 1” Screw (32) 5/16" x 2 1/2" Carriage Bolt (1) 5/16" x 2 1/2" Bolt (3) 5/16" x 2 3/4&#...

Page 31 - EXPLODED DRAWING—Model No. WESY99300

65 13 70 37 25 26 66 37 65 67 18 18 71 25 26 37 18 71 68 15 27 18 69 51 82 42 13 45 2 2 2 88 11 16 19 20 74 2 2 38 73 4 1 39 5 35 1 61 39 5 7 4 4 39 5 35 2 2 4 17 39 5 35 62 4 5 5 22 36 2 6 21 14 38 38 41 46 20 64 2 38 39 5 7 20 19 46 63 5 24 72 2 2 17 18 2 17 4 34 22 18 17 6 6 72 2 9 43 11 16 78 77...