Weider WESY96310 - Manuals - manualsarea.com

Page 2 - TABLE OF CONTENTS

2 IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4ASS...

Page 3 - IMPORTANT PRECAUTIONS

WARNING: To reduce the risk of serious injury, read the following important precau- tions before using the weight system. 1. Read all instructions in this manual and in the accompanying literature before using theweight system. Use the weight system onlyas described in this manual. 2. It is the resp...

Page 4 - BEFORE YOU BEGIN

BEFORE YOU BEGIN 4 ASSEMBLED DIMENSIONS: Height: 76 in.Width: 89 in. Length: 64 in. Foot Plate Low PulleyStation High Pulley Station Lat Bar Leg Lever Butterfly Arms Military Press Arm Press Arm Weight Stacks Backrests VKR Arms Decal 1 Decal 1 Decal 1 Decal 2 Decal 3 Leg Press Plate Thank you for se...

Page 5 - FRAME ASSEMBLY; ASSEMBLY

5 1 8 11 51 27 1 1 4 3 1 51 5 1. Before beginning assembly, be sure that youhave read and understand the information inthe box above. Locate and open the parts bag labeled“FRAME ASSEMBLY.” Press two 2” Square Outer Caps (51) onto theStabilizer (5) in the indicated locations. Press a 2”Square Inner C...

Page 9 - ARM ASSEMBLY

9 9. Attach the upper ends of the Short Weight Guides(73) to the Top Frame (55) with a 5/16” x 6” Bolt(60), two 1/2” x 3/4” Spacers (61), and a 5/16”Nylon Locknut (3). Attach the upper ends of the Long Weight Guides(62) to the Top Frame (55) with a 5/16” x 6” Bolt(60), two 1/2” x 3/4” Spacers (61), ...

Page 11 - CABLE ASSEMBLY

11 15. See the inset drawing. Attach the Military Press Arm (84) to the Pivot Arm (101) with two 5/16” x 2 1/4” Bolts (33) and two 5/16” Nylon Locknuts(3). Press two 1 1/2” Square Inner Caps (32) into theindicated end of the Military Press Arm (84).Press two 1” Round Inner Caps (49) into theMilitary...

Page 18 - SEAT ASSEMBLY

18 36. Attach the Press Bracket (94) to the Leg Press Arm (96) with a 3/8” x 3” Bolt (103) and a 3/8”Nylon Jamnut (104). Wrap the Leg Press Cable (99) around a 3 1/2”Pulley (15). Attach the Pulley to the Press Bracket(94) with the 3/8” x 2” Bolt (12) and a 3/8” NylonLocknut (21). Slide a 5/16” Washe...

Page 20 - VKR ASSEMBLY

20 43. Press two 3/4” Round Inner Caps (34) into each Pad Tube (28). Insert a Pad Tube (28) into the Front Seat Frame(36). Slide a Foam Pad (30) onto each end of thePad Tube. Insert the other Pad Tube (28) into the Leg Lever(29). Slide a Foam Foam Pad (30) onto each endof the Pad Tube. 44. Locate an...

Page 21 - ADJUSTMENTS

21 The instructions below describe how each part of the weight system can be adjusted. Refer to the exerciseguide accompanying this manual to see how the weight system should be set up for each exercise. IMPOR- TANT: When attaching the lat bar or nylon strap, make sure that the attachments are in th...

Page 23 - WEIGHT RESISTANCE CHART

23 This chart shows the approximate weight resistance at each weight station. “Top” refers to the 6.5 lb. top weight.The other numbers refer to the 12.5 lb. weight plates. The butterfly arm resistance listed is the resistance foreach butterfly arm. The actual resistance at each weight station may va...

Page 24 - TROUBLE-SHOOTING AND MAINTENANCE

24 TROUBLE-SHOOTING AND MAINTENANCE Make sure all parts are properly tightened each time you use the weight system. Replace any worn parts immedi-ately. The weight system can be cleaned using a damp cloth and mild non-abrasive detergent. Do not use solvents. TIGHTENING THE CABLES Woven cable, the ty...

Page 25 - CABLE DIAGRAMS

25 The cable diagrams on these pages show the proper routing of the High Cable (58), the Low Cable (23), theMilitary Press Cable (72), and the Leg Press Cable (99). Use the diagrams to be sure that the four cables andthe cable traps have been assembled correctly. If the cables have not been correctl...

Page 27 - PART IDENTIFICATION CHART—Model No. WESY96310

5/16" Nylon Locknut (3) 1/4" Washer (10) 5/16" Washer (8) 1" Retainer (69) 3/8" Washer (9) 3/8" Nylon Locknut (21) 1 1/8" x 2 1/2" Plastic Bushing (89) 5/16" Nylon Jamnut (93) 5/16" x 2" Eyebolt (35) 3/8" Nylon Jamnut (104) 3/8" x 8" Bolt (59) ...

Page 29 - Cab

1" Round Inner Cap (49) 1" Round Cover Cap (70) 1/2" x 3/4" Spacer (61) Round Inner Cap (102) 1 1/2" Square Inner Cap (32) 1 3/4" Square Inner Cap (44) 2" Square Inner Cap (27) 2" Square Outer Cap (51) 5/8" x 9/16" Spacer (7) 3/4" Round Inner Cap (34) 1...

Page 31 - EXPLODED DRAWING—Model No. WESY96310

60 27 21 15 55 12 11 8 15 12 44 88 15 58 21 44 21 3 61 62 24 3 58 71 2 65 63 64 25 26 19 21 9 3 3 49 6 22 46 46 16 3 9 15 21 59 23 21 17 27 1 4 10 43 41 42 21 3 50 31 86 70 69 69 70 21 47 44 45 44 45 48 50 31 86 13 40 38 37 18 32 34 30 28 3 49 83 33 10 2 36 14 88 15 29 35 30 34 34 30 28 3 8 32 30 34...