Weider WESY91080 - Manuals - manualsarea.com

Page 3 - Before You Begin

3 ASSEMBLED DIMENSIONS: Height: 79 in.Width: 38 in. Length: 91 in. Low Pulley Station Foot Plate High Pulley Station Leg Lever Butterfly Arms Press Arm Weight Stack Seat Backrest Thank you for selecting the versatile WEIDER ¨ PRO 9628 Home Gym System. The PRO 9628 offers aselection of weight station...

Page 4 - Assembly

4 Note: This introduction will save you moretime than it takes to read it! Identifying Parts To help you identify the small parts used in assem-bly, we have included a PART IDENTIFICATIONCHART located in the center of this manual. Placethe chart on the floor or work table and use it toquickly identi...

Page 5 - Frame Assembly

1. Before beginning, be sure that you have read andunderstood the information on page 4. Locate and open the parts bag labeled ÒFRAMEASSEMBLY.Ó Press a 2Ó Square Cover Cap (78) onto each end ofthe Stabilizer (5). Insert two 3/8Ó x 2 3/4Ó Carriage Bolts (94) up throughthe Stabilizer (5) and place it ...

Page 8 - Arm Assembly

8 13. Press Arm AssemblyÑLocate and open the partsbag labeled ÒARM ASSEMBLY.Ó Press a 1Ó x 7/8Ó Plastic Bushing (75) onto eachwelded spacer on the Press Frame (17). Align thewelded spacers on the Press Frame with the tube (A)on the Top Frame (55). Note: This will be a tight fit. The Plastic Bushings...

Page 10 - Cable Assembly

10 18. Locate and open the parts bag labeled ÒCableAssembly and Pulleys.Ó For Cable identificationand routing during steps 18-35, refer to the CableDiagram and Cable ID Chart on page 19. Tighten the Bolt and Locknut on the pre-assembledPulley (15) on the Top Frame (55) Attach a ÒVÓ-Pulley (6) and a ...

Page 15 - Seat Assembly

15 35. Locate and open the parts bag labeled ÒSeatAssembly.Ó Attach the Backrest (41) with the name decal to thePress Upright (56) with two 1/4Ó x 2 1/2Ó Screws (43)and two 1/4Ó Flat Washers (10). 35 Seat Assembly 33. Remove the 3 1/2Ó Pulley (15) from the Long ÒUÓ- Bracket (57). Route the Medium Ca...

Page 17 - Miscellaneous Assembly

40. Press a 1 1/2Ó Square Inner Cap (32) into the Leg Lever (29). Lubricate the 5/16Ó x 2 1/4Ó Bolt (33). Attach the LegLever (29) to the Seat Frame (36) with the Bolt and a 5/16Ó Nylon Locknut (3). Do not overtighten the Nylon Locknut. The LegLever must be able to pivot freely. Insert the 5/16Ó x 2...

Page 19 - Cable Diagram

19 46. Make sure that all parts have been properly tightened. The use of the remaining parts will be explained in ADJUSTMENT, beginning on page 20 of this manual. Before using the home gym system, pull each cable a few times to be sure that the cables move smoothlyover the pulleys. If one of the cab...

Page 20 - Adjustment; Changing the Weight Setting

20 Attaching the Lat Bar or Nylon Strap to theHigh Pulley Station Attach the Lat Bar (54) to the Short Cable (23) with aCable Clip (53). For some exercises, the Chain (52)should be attached between the Lat Bar and the MediumCable with two Cable Clips. Adjust the length of the Chain between the Lat B...

Page 21 - Adjusting the Position of the Foot Plate

21 Attaching the Leg Lever to the Low PulleyStation To use the Leg Lever (29), the seat must be attached tothe Butterfly upright (see ATTACHING AND REMOVINGTHE BUTTERFLY SEAT on page 20). Attach one end of the Chain (52) to the Medium Cable(86) with a Cable Clip (53). Attach the other end of theChai...

Page 22 - Weight Resistance Chart

22 Press Butterfly High Leg Leg Low Weight Arm Arm Pulley Lever Press Pulley Plates (lbs.) (lbs.) (lbs.) (lbs.) (lbs.) (lbs.) Top 19 5 7 7 31 7 1 41 10 20 17 74 17 2 62 23 30 30 115 30 3 84 32 40 43 146 43 4 108 38 53 58 183 58 5 131 43 65 68 220 68 6 168 48 76 83 283 83 7 195 51 87 95 334 95 8 225 ...

Page 23 - Tightening the Cables; Trouble-shooting and Maintenance

23 Tightening the Cables Woven cable, the type of cable used on the home gymsystem, can stretch slightly when it is first used. If there isslack in the Cables before resistance is felt, the Cablesshould be tightened. Insert the Weight Pin (26) under oneof the indicated Weights (25). Slack can be rem...

Page 27 - Exploded DrawingÑModel No. WESY91080

12 20 15 66 21 41 10 43 23 72 3 10 2 12 81 81 15 15 21 1043 41 3 21 6 50 7 78 78 19 93 93 1 51 5 12 15 66 1 27 21 21 66 16 15 3 3 9 83 34 34 30 30 35 32 8 3 28 30 34 28 30 34 10 33 2 24 14 40 38 18 37 13 45 45 44 44 70 69 69 70 74 7 50 6 21 74 11 8 27 12 15 21 16 15 44 49 83 27 23 44 3 55 61 21 60 6...

Page 28 - Part ListÑModel No. WESY91080

Note: Ò#Ó indicates a non-illustrated part. Specifications are subject to change without notice. Key No. Qty. Description 1 6 5/16Ó x 2 1/2Ó Carriage Bolt 2 4 1/4Ó Nylon Locknut 3 23 5/16Ó Nylon Locknut 4 1 Butterfly Base 5 1 Stabilizer 6 6 ÒVÓ-Pulley 7 4 3/8Ó x 2 1/2Ó Bolt 8 11 5/16Ó Flat Washer 9 ...