Weider WESY85070 - Manuals

Weider WESY85070 – Manual in PDF format online.

Manuals:

Manual

Manual Weider WESY85070

Summary

Page 3 - BEFORE YOU BEGIN

3 BEFORE YOU BEGIN ASSEMBLED DIMENSIONS: Height: 77 in.Width: 39 in. Length: 48 in. Foot Plate Low Pulley Station High Pulley Station Lat Bar Leg Lever Arms Weight Stack Backrest Weight Pin Thank you for selecting the versatile WEIDER ¨ 8507 Training System. The WEIDER 8507 offers an impres-sive arr...

Page 4 - ASSEMBLY; Assembly requires two people.

4 ASSEMBLY Assembly requires two people. Due to the size and weight of the home gym system, assemble it inthe location where it will be used. ¥ Place all parts of the home gym system in a cleared area and remove the packing materials;do not dispose of the packing materials untilassembly is completed...

Page 5 - center hole; Do not tighten the Nylon Locknuts yet.

5 3. Slide six Weights (25) on the Weight Guides (72).Be sure that all of the Weights are turned so the pingrooves are on the indicated side. 4. Press the 1 1/4Ó Square Inner Cap (57) into theFront Upright (42). Attach the 1Ó Plastic Stop (64) to the center hole in the Stop Bracket (63) with a 5/16Ó...

Page 6 - en the Nylon Locknuts yet.

6 5. Press the Weight Tube Bumper (79) into the end ofthe Weight Tube (80). Slide the Top Weight (77)onto the Weight Tube. Be sure that the pins on theWeight Tube are resting in the pin grooves underthe Top Weight. Locate the Short Cable (23). Attach the Short Cable to the Weight Tube (80) with a 5/...

Page 7 - The

7 8. Attach the upper ends of the Weight Guides (72) tothe Top Frame (67) with the 5/16Ó x 6Ó Bolt (74), two1/2Ó x 3/4Ó Spacers (73), and a 5/16Ó Nylon Locknut(3). Tighten all Nylon Locknuts used in steps 4through 8. 9. Press two 1 3/4Ó Square Inner Caps (44), two 1 1/2ÓSquare Inner Caps (32), and t...

Page 8 - The teeth

8 11. Press a 1 3/4Ó Square Inner Cap (44) into each end of an Arm (46). Apply lubricant to the lower axles on the Arm Frame(52). Slide an Arm (46) onto one of the axles. Holdtwo 1Ó Retainers (54) and a 1Ó Round Cover Cap(55) against the lower end of the axle. The teeth on the Retainers must bend to...

Page 9 - Be sure that the

9 14. Attach a Large ÒUÓ Bracket (56) to one of the Arms (46) with a 3/8Ó x 2 3/4Ó Bolt (70), 3/8Ó Flat Washer(9), and 3/8Ó Nylon Locknut (21). Be sure that the Swivel Bracket (58) is on the inside as shown.Do not overtighten the 3/8Ó Nylon Locknut. Attach a Large ÒUÓ Bracket (56) to the other Arm(4...

Page 11 - Be sure

11 19. Note: The 4 1/2Ó Pulley (81) shown in this stepis pre-attached to the Adjustment ÒUÓ Bracket(75). Remove the 3/8Ó x 1 3/4Ó Bolt (48), 3/8Ó NylonLocknut (21), and 4 1/2Ó Pulley (81) from theAdjustment ÒUÓ Bracket (75). Attach the Adjustment ÒUÓ Bracket (75) to the FrontUpright (42) with the 5/...

Page 13 - Be sure that the Short

13 23. Attach the 5/16Ó x 3 1/2Ó Bolt (87), two 5/16Ó Flat Washers (8), the 1Ó Metal Spacer (22), and a 5/16ÓNylon Locknut (3) to the Front Upright as shown. Wrap the Short Cable (23) around a 3 1/2Ó Pulley(15). Attach the Pulley to the Front Upright (42) witha 3/8Ó x 3 1/2Ó Bolt (16), a 3/8Ó Washer...

Page 14 - Do not overtighten the

14 26. Press a 1 1/2Ó Square Inner Cap (32) into the Leg Lever (29). Attach the 5/16Ó x 2Ó Eyebolt (62) to the Leg Lever(29) with a 5/16Ó Flat Washer (8) and a 5/16Ó NylonLocknut (3). Lubricate a 5/16Ó x 2 1/4Ó Bolt (33). Attach the LegLever (29) to the Seat Frame (36) with the Bolt anda 5/16Ó Nylon...

Page 15 - IMPORTANT: If the cables

15 29. Slide a Handgrip (12) onto each end of the Lat Bar (85). 29 85 12 12 30. Make sure that all parts are properly tightened. The use of all remaining parts will be explained in ADJUST- MENT, beginning on page 16 of this manual. Before using the home gym system, pull each cable a fewtimes to make...

Page 16 - ADJUSTMENT; CHANGING THE WEIGHT SETTING

16 ADJUSTMENT The instructions below describe how each part of the home gym system can be adjusted. Refer to theEXERCISE GUIDE accompanying this manual to see how the home gym system should be set up for eachexercise. IMPORTANT: When attaching the lat bar or nylon strap, make sure that the attachmen...

Page 18 - Adjust the length of the

18 ATTACHING THE LAT BAR OR NYLON STRAP TOTHE LOW PULLEY STATION Attach the Lat Bar (85) to the Short Cable (23) with aCable Clip (83). For some exercises, the Chain (84)should be attached between the Lat Bar and the ShortCable with two Cable Clips. Adjust the length of the Chain between the Lat Bar...

Page 19 - TROUBLE-SHOOTING AND MAINTENANCE; TIGHTENING THE CABLES

19 TROUBLE-SHOOTING AND MAINTENANCE Inspect and tighten all parts each time you use the home gym system. Replace any worn parts immediately. Thehome gym system can be cleaned using a damp cloth and mild non-abrasive detergent. Do not use solvents. TIGHTENING THE CABLES Woven cable, the type of cable...

Page 21 - EXPLODED DRAWINGÑModel No. WESY85070

39 56 21 58 15 5 15 15 78 78 5 88 71 4 19 1 27 34 34 32 34 29 3 33 7 30 10 28 34 32 36 13 38 37 18 40 14 23 87 8 22 16 15 3 3 8 3 5 9 26 88 42 41 10 43 25 79 80 85 84 83 45 44 8 33 49 51 47 8 3 54 55 46 9 70 55 54 3 8 49 47 33 45 44 51 9 70 46 44 53 53 44 44 49 52 60 49 57 8 3 3 11 8 3 64 24 63 3 72...

Page 22 - CABLE DIAGRAMS

22 CABLE DIAGRAMS The cable diagrams below show the proper routing of the Short Cable (23) and the Long Cable (66). Use thediagram to make sure that the two cables are assembled correctly. The numbers show the routing of each cable. Short Cable (23) Long Cable (66) Weight StackÑ 1 Low PulleyÑ 3 2 Hi...

Page 26 - ORDERING REPLACEMENT PARTS; LIMITED WARRANTY

ORDERING REPLACEMENT PARTS To order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Mondaythrough Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). To help us assist you, please be pre-pared to give the following information: 1. The MODEL NUM...