Weider WESY49202 - Manuals - manualsarea.com

Page 2 - IMPORTANT PRECAUTIONS

1. Read all instructions in this manual and inthe accompanying literature before using theweight system. 2. It is the responsibility of the owner to ensurethat all users of the weight system are ade-quately informed of all precautions. 3. The weight system is intended for home useonly. Do not use th...

Page 3 - BEFORE YOU BEGIN

3 BEFORE YOU BEGIN ASSEMBLED DIMENSIONS: Height: 78 in.Width: 110 in. Length: 92 in. Foot Plate High Pulley Station Lat Bar Leg Lever Butterfly Arms Assist Arm Press Arm Weight Stacks Backrests Dip Handles Pull-up Handles Warning Decal 1 Warning Decal 1 Warning Decal 3 Warning Decal 2 Leg Press Plat...

Page 4 - ASSEMBLY; FRAME ASSEMBL

4 ASSEMBLY 1 8 8 11 51 27 1 4 3 1 51 5 1. Before beginning assembly, be sure thatyou have read and understand the infor-mation in the box above. Locate and open the parts bag labeled“FRAME ASSEMBLY.” Press two 50mm Square Outer Caps (51)onto the Stabilizer (5). Press a 50mmSquare Inner Cap (27) into...

Page 9 - ARM ASSEMBL

9 12. Press a 25mm Round Inner Cap (49) into one of the Press Arms (46). Press a 45mmSquare Inner Cap (44) into the Press Arm. Attach the Press Arm (46) to one side of thePress Frame (17) with two M8 x 60mm Bolts(22) and two M8 Nylon Locknuts (3). Assemble the other Press Arm (46) in thesame manner....

Page 12 - CABLE ASSEMBL

12 20. Wrap the High Cable (58) around a “V”-Pulley (50). Attach the Pulley and a Long Cable Trap(31) to the indicated bracket on the FrontUpright (42) with an M10 x 55mm Bolt (86)and an M10 Nylon Locknut (21). Be sure thatthe Long Cable Trap is positioned to holdthe Cable in place. 21. Route the Hi...

Page 19 - SEA

19 40. Locate and open the parts bag labeled “SEAT ASSEMBLY.” Insert an M6 x 60mm Carriage Bolt (92)through the center hole in a Seat Plate (37).Attach the Seat Plate to the Rear Backrest(85) with two M6 x 16mm Screws (18). Insert the M6 x 60mm Carriage Bolt (92)through the indicated hole in the Leg...

Page 22 - ADJUSTMENTS

22 ADJUSTMENTS The instructions below describe how each part of the weight system can be adjusted. Refer to the exerciseguide accompanying this manual to see how the weight system should be set up for each exercise. IMPOR-TANT: When attaching the lat bar or nylon strap, make sure that the attachment...

Page 24 - WEIGHT RESISTANCE CHART

24 WEIGHT RESISTANCE CHART This chart shows the approximate weight resistance at each weight station. “Top” refers to the 6.5 lbs. topweight. The other numbers refer to the 12.5 lbs. weight plates. The butterfly arm resistance listed is the resis-tance for each butterfly arm. WEIGHT PRESS BUTTERFLY ...

Page 25 - TROUBLESHOOTING AND MAINTENANCE

TROUBLESHOOTING AND MAINTENANCE Make sure all parts are properly tightened each time you use the weight system. Replace any worn parts immedi-ately. The weight system can be cleaned using a damp cloth and mild non-abrasive detergent. Do not use solvents. TIGHTENING THE CABLES Woven cable, the type o...

Page 26 - CABLE DIAGRAMS

26 CABLE DIAGRAMS The cable diagrams on these pages show the proper routing of the High Cable (58), the Low Cable (23), theMilitary Press Cable (72), and the Leg Press Cable (99). Use the diagrams to be sure that the four cables andthe cable traps have been assembled correctly. If the cables have no...

Page 28 - PART IDENTIFICATION CHART—Model No. WESY49202

M8 x 60mm Bolt (22) M8 x 45mm Bolt (24) M8 x 55mm Bolt (33) M10 x 50mm Bolt (12) M10 x 45mm Bolt (76) M10 x 55mm Bolt (86) M6 x 50mm Carriage Bolt (38) M6 x 70mm Screw (114) M6 x 60mm Carriage Bolt (92) M6 x 50mm Screw (81) M6 x 65mm Screw (43) M6 x 16mm Screw (18) M6 Washer (10) M10 Nylon Locknut (...

Page 32 - EXPLODED DRAWING—Model No. WESY49202

60 27 21 50 55 86 11 8 15 12 44 88 15 58 21 44 21 3 61 62 24 3 58 71 3 65 108 64 25 26 19 9 3 3 49 6 22 46 46 16 3 9 15 21 59 23 21 17 27 1 4 10 43 41 42 21 3 50 31 86 70 69 69 70 21 47 44 45 44 45 48 50 31 86 13 40 38 37 18 32 34 30 28 3 49 83 33 10 2 36 14 15 29 35 30 34 34 30 28 21 9 32 30 34 8 1...

Page 33 - ORDERING REPLACEMENT PARTS; LIMITED WARRANTY

ORDERING REPLACEMENT PARTS To order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Mondaythrough Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). To help us assist you, please be pre-pared to give the following information: 1. The MODEL NUM...