Weider WESY17011 - Manuals

Weider WESY17011 – Manual in PDF format online.

Manuals:

Manual

Manual Weider WESY17011

Summary

Page 2 - TABLE OF CONTENTS

2 TABLE OF CONTENTS IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

Page 3 - IMPORTANT PRECAUTIONS

1. Read all instructions in this manual and in the accompanying literature before using theweight system. 2. It is the responsibility of the owner to ensurethat all users of the weight system are ade-quately informed of all precautions. 3. The weight system is intended for home useonly. Do not use t...

Page 4 - BEFORE YOU BEGIN

4 ASSEMBLED DIMENSIONS: Height: 76 in.Width: 37 in. Length: 48 in. Foot Plate Low Pulley Station High Pulley Station Lat Bar Leg Lever Butterfly Arms Press Arm Curl Pad Weight Carriage Seat Backrest BEFORE YOU BEGIN Thank you for selecting the versatile WEIDER ® 15CT weight system. The WEIDER ® 15CT...

Page 5 - ASSEMBLY

5 Make sure you have the following tools: • Two adjustable wrenches • One standard screwdriver • One phillips screwdriver • One rubber mallet • You will also need grease or petroleum jelly, a small amount of soapy water, and clear tape ormasking tape. Note: Assembly will be more convenient if you ha...

Page 6 - FRAME ASSEMBLY

6 1 56 3 5 51 51 14 1 27 4 1. Before beginning assembly, be sure that youhave read and understand the information inthe box on the previous page. Press a 50mm Square Outer Cap (51) onto eachend of the Stabilizer (5). Press a 50mm SquareInner Cap (27) into the end of the Base (4). Insert two M8 x 67m...

Page 7 - ARM ASSEMBLY

7 4 4 Tube Welded Spacers 17 59 Lubricate 21 9 9 3. Press a 45mm Square Inner Cap (44) into eachend of the crossbar on the Top Frame (55). Presstwo 25mm Round Inner Caps (49) into the top ofthe crossbar. Press a 50mm Square Inner Cap(27) into the top of the Rear Upright (56). Attach the Top Frame (5...

Page 8 - CABLE ASSEMBLY

8 7. Lubricate both axles on the Top Frame (55). Slidethe Right Arm (48) onto the right axle. Note: Becareful not to confuse the Right Arm with theLeft Arm (47); refer to step 6 to identify theRight Arm. Be sure that the upper end of theRight Arm is behind the indicated bracket onthe Top Frame. Tap ...

Page 13 - SEAT ASSEMBLY

23. Attach the Backrest (41) to the Front Upright (42) with two M6 x 63mm Screws (43) and two M6Washers (10). SEAT ASSEMBLY 23 41 42 10 43 13 24. Press a 38mm Square Inner Cap (32) into the Seat Frame (36). Insert an M6 x 50mm Carriage Bolt (38) into thecenter hole in the Seat Plate (37). Attach the...

Page 16 - ADJUSTMENT

16 ADJUSTMENT The instructions below describe how each part of the weight system can be adjusted. Refer to the exerciseguide accompanying this manual to see how the weight system should be set up for each exercise. IMPOR-TANT: When attaching the lat bar or nylon strap, make sure that the attachments...

Page 18 - WEIGHT RESISTANCE CHART

18 WEIGHT ON PRESS ARM BUTTERFLY ARM LOW PULLEY/ HIGH PULLEY WEIGHT (lbs.) (lbs.) LEG LEVER (lbs.) CARRIAGE (lbs.) 0 12 7 10 10 5 22 11 18 16 10 31 15 25 21 15 40 20 32 26 20 50 24 39 32 25 59 29 46 37 30 68 33 53 42 35 78 38 61 47 40 87 42 68 53 45 97 47 75 58 50 106 51 82 63 55 115 56 89 68 60 125...

Page 19 - TROUBLE-SHOOTING AND MAINTENANCE

19 TROUBLE-SHOOTING AND MAINTENANCE Make sure all parts are properly tightened each time you use the weight system. Replace any worn parts immedi-ately. The weight system can be cleaned using a damp cloth and mild non-abrasive detergent. Do not use solvents. TIGHTENING THE CABLES Woven cable, the ty...

Page 20 - CABLE DIAGRAM

20 CABLE DIAGRAM The cable diagram below shows the proper routing of the Short Cable (23) and the Long Cable (58). Use the dia-gram to be sure that the two cables and the cable traps have been assembled correctly. If the cables have notbeen correctly routed, the weight system will not function prope...

Page 21 - NOTES

Page 23 - EXPLODED DRAWING—Model No. WESY17011

15 23 56 15 12 3 57 23 21 3 5 51 14 51 4 1 27 16 7 50 6 21 63 62 63 62 47 48 44 45 44 45 13 40 38 37 18 32 28 30 34 10 2 24 36 30 34 14 61 3 29 34 30 28 49 46 32 30 34 49 49 46 22 3 9 25 59 17 21 52 44 44 8 66 54 31 31 26 60 60 49 19 27 61 58 21 49 49 11 69 67 66 15 61 55 12 15 44 15 16 58 21 44 21 ...

Page 24 - PART IDENTIFICATION CHART—WESY17011

M10 Eyebolt (35) M6 Nylon Locknut (2) M8 Nylon Locknut (3) M10 Nylon Locknut (21) M6 Washer (10) M8 Washer (8) M6 x 50mm Screw (24) M6 x 63mm Screw (43) M8 x 63mm Bolt (22) Cable Clip (53) M10 Washer (9) M8 x 63mm Carriage Bolt (1) M6 x 16mm Screw (18) M6 x 50mm Carriage Bolt (38) PART IDENTIFICATIO...

Page 27 - ORDERING REPLACEMENT PARTS

To order replacement parts, call our Customer Service Department toll-free at 1-800-999-3756, Monday throughFriday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). To help us assist you, please be prepared to givethe following information: • The MODEL NUMBER of the product (WESY17011) • The ...