Weider WESY13820 - Manuals

5 Before beginning assembly, carefully read thefollowing information and instructions: • Assembly requires two people. • Place all parts in a cleared area and remove the packing materials. Do not dispose of the packingmaterials until assembly is completed. • Tighten all parts as you assemble them, u...

7 5. Press two 25mm x 50mm Inner Cap (42) into thetop of the Press Frame (9). Press two 50mmSquare Inner Caps (44) into the ends of thePress Frame. Orient the Press Frame (9) with the bracket onthe side shown. Attach the Press Frame to theTop Frame (5) with an M10 x 125mm Bolt (54),two M10 Washers (...

8 10. Route the High Cable (35) down through the Top Frame (5) and around a Pulley (39). Attach thePulley and a Cable Trap (41) to the second set ofholes from the top of the two Pulley Plates (14)with an M10 x 48mm Bolt (77) and an M10 NylonLocknut (56). Be sure the Cable Trap is turnedto hold the C...

13 28. Insert an M6 x 50mm Carriage Bolt (62) into the center hole in the Seat Plate (24). Attach the SeatPlate to the Seat (17) with two M6 x 16mmScrews (59). Attach the Seat (17) to the Seat Frame (6) withthe M6 x 50mm Carriage Bolt (62), an M6 x50mm Screw (64), two M6 Washer (63), and anM6 Nylon ...

15 This section explains how to adjust the weight system. Refer to the accompanying exercise guide to see the cor-rect form for each exercise. Make sure all parts are properly tightened each time the weight system is used. Replace any worn parts immediate-ly. The weight system can be cleaned with a ...

WEIGHT (lbs.) 0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125 PRESS ARM (lbs.) 18 26 34 42 50 58 64 70 76 82 88 97 106 115 124 133 138 143 148 153 158 166 174 183 191 201 BUTTERFLY ARM (lbs.) 12 16 20 24 28 33 37 41 45 49 53 57 61 65 69 73 77 81 85 89 93 97 101 105 ...

High Cable (35) CABLE DIAGRAMS The cable diagrams below show the proper routing of the High Cable (35), the Arm Cable (36), the Low Cable(37), and the Short Cable (80). Use the diagrams to make sure that the cables and the cable traps have beenassembled correctly. If the cables have not been correct...

19 TIGHTENING THE CABLES Woven cable, the type of cable used on the weightsystem, can stretch slightly when it is first used. Ifthere is slack in the cables before resistance is felt,the cables should be tightened. Slack can be removed by moving a Pulley (39) andCable Trap (41) to a set of holes clo...

M10 Nylon Locknut (56) M8 Nylon Locknut (61) M6 Nylon Locknut (58) 19mm Round Inner Cap (49) 50mm Square Inner Cap (44) 25mm x 50mm Inner Cap (42) 45mm Square Inner Cap (45) 38mm Square Inner Cap (48) 50mm Square Outer Cap (50) Dome Cap (47) Large Washer (67) 25mm Round Inner Cap (43) PART IDENTIFIC...

Key No. Qty. Description Key No. Qty. Description 1 1 Base 2 1 Stabilizer 3 1 Rear Upright 4 1 Front Upright 5 1 Top Frame 6 1 Seat Frame 7 1 Leg Lever 8 1 Curl Post 9 1 Press Frame 10 1 Right Arm 11 1 Left Arm 12 1 Lat Bar 13 1 Nylon Strap 14 2 Pulley Plate 15 1 Double “U”-Bracket 16 1 Backrest 17 ...

EXPLODED DRAWING—Model No. WESY13820 R0902B 61 81 80 76 56 77 39 41 13 12 33 33 39 68 56 39 77 56 5 39 74 73 44 61 72 25 55 61 60 35 56 55 74 71 56 30 38 40 36 44 45 9 56 55 55 54 42 43 28 58 57 19 46 10 11 47 34 43 16 37 29 42 78 69 38 30 56 56 71 56 69 40 63 70 19 34 47 3 39 56 15 56 68 68 77 39 3...

ORDERING REPLACEMENT PARTS To order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Mondaythrough Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). To help us assist you, please be pre-pared to give the following information: • The MODEL NUMB...