Weider 831.159530 - Manuals

Page 2 - TABLE OF CONTENTS

2 IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4A...

Page 3 - IMPORTANT PRECAUTIONS; Keep hands and

1. Read all instructions in this manual and in the accompanying literature before using theweight system. 2. It is the responsibility of the owner to ensure that all users of the weight system are ade-quately informed of all precautions. 3. The weight system is intended for home use only. Do not use...

Page 4 - BEFORE YOU BEGIN

4 ASSEMBLED DIMENSIONS: Height: 77 in.Width: 103 in. Depth: 55 in. Low PulleyStation Foot Plate Leg Lever Press Arms Decal 1 Decal 1 Decal 2 Backrest Curl Pad Butterfly Arms Ab Pulley Station Leg Press Arm Thank you for selecting the innovative and versatileWEIDER ® PRO 9950 weight system. The WEIDE...

Page 5 - ASSEMBLY

5 Make sure you have the following tools: • Two adjustable wrenches • One standard screwdriver • One phillips screwdriver • One rubber mallet • You will also need grease or petroleum jelly, a small amount of soapy water, and clear tape ormasking tape. Note: Assembly will be more convenient if you ha...

Page 6 - Frame Assembly

1. Before beginning, make sure that you haveread and understood the information on page 5. Locate and open the parts bags labeled“FRAME ASSEMBLY 1 and 2.” Press a 2” Square Inner Cap (59) into each endof the Butterfly Base (1). Insert four 5/16” x 2 1/2” Carriage Bolts (54) upthrough the Butterfly B...

Page 10 - Arm Assembly

85 86 Axle 10 15. Locate and open the parts bag labeled “ARMASSEMBLY.” Press a 2” Square Inner Cap (59) into each endof the Leg Lever (8). Lubricate the 3/8” x 3 1/4” Bolt (101). Attach theLeg Lever (8) to the Butterfly Front Leg (9) withthe Bolt and a 3/8” Nylon Jamnut (88). 16. Press two 1 3/4” Sq...

Page 12 - Cable Assembly

21 12 24. Wrap the Press Cable (80) around a 3 1/2” Pulley (37). Attach the Pulley to the indicated side of thePress Frame (14) with a 3/8” x 3 1/2” Bolt (65), a3/8” Washer (75), and a 3/8” Nylon Locknut (74). 24 22. Locate and open the parts bag labeled“CABLE ASSEMBLY.” For Cable identificationand ...

Page 20 - Seat Assembly

20 53. Locate and open the parts bag labeled “SEATASSEMBLY.” Press a 1 1/2” Square Inner Cap (100) into thebottom of a Seat Bracket (11). Press two 1” x 2”Inner Caps (70) into the ends of the Seat Bracket. Insert a 1/4” x 1 3/4” Carriage Bolt (93) into thecenter hole of a Support Plate (57). Attach ...

Page 23 - ADJUSTMENTS

ADJUSTING THE SEAT To adjust the height of the Seat (25) on the PressSeat Frame (12), loosen the Adjustment Knob (51) byturning it counterclockwise, and pull it out as far aspossible. Move the Seat to the desired height andsnap the Knob into an adjustment hole in the SeatBracket (11). Turn the Adjus...

Page 25 - WEIGHT RESISTANCE CHART

25 Weight High Arm Leg Butterfly Leg Lever Low Arm (lbs.) Pulley Press Press Arm (lbs.) Pulley (lbs.) (lbs.) (lbs.) (lbs.)* (lbs.) 20 30 23 44 9 26 22 40 60 45 88 18 52 45 60 90 68 132 27 78 67 80 120 90 176 36 104 90 100 150 113 220 45 130 112 120 180 135 264 55 156 135 140 210 158 308 64 182 157 1...

Page 26 - CABLE DIAGRAMS

26 The cable diagrams below show the proper routing of the Butterfly Cable (81), the Ab Cable (83), the Leg LeverCable (82) and the Press Cable (80). The numbers show the correct route for each Cable. Make sure that the Cables are routed correctly, that the pulleys move smoothly, and that the cable ...

Page 27 - TROUBLE-SHOOTING AND MAINTENANCE

27 Slack can be removed form the Press Cable (80) bymoving the indicated “V”-Pulley (38) to one of the fourfree holes in the Press Seat Frame (12). Remove the3/8” x 4 1/4” Bolt (104), 3/8” Washer (75), and 3/8”Nylon Locknut (74) from the Press Seat Frame,Pulley, and Long Cable Trap (50). Reattach th...

Page 28 - FULL 90 DAY WARRANTY

Part No. 177796 R1001A Printed in Canada © 2001 Sears, Roebuck and Co. SEARS, ROEBUCK AND CO., HOFFMAN ESTATES, IL 60179 Model No. 831.159530 QUESTIONS? If you find that: • you need help assembling or operating the WEIDER ® PRO 9950 weight system • a part is missing • or you need to schedule repair ...