Weed Eater WET6500A - Manuals

6 ASSEMBLY ATTACH CLUTCH CABLE (See Fig. 6) • Hook end of clutch cable through hole in control bar bracket if necessary. CONTROL BAR BRACKET CLUTCH CABLE CONTROL BAR FIG. 6 END OFCLUTCH CABLE CONTROL BAR BRACKET SHIFTROD HAIRPINCLIP SHIFTLEVERINDICATOR FIG. 7 CONNECT SHIFT ROD (See Fig. 7) • Insert ...

7 OPERATION KNOW YOUR TILLER READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TILLER. Compare the illustrations with your tiller to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. These symbols may appear on your Tille...

8 OPERATION HOW TO USE YOUR TILLER Know how to operate all controls before adding fuel and oil or attempting to start engine. STOPPING (See Fig. 9) TINES AND DRIVE • Release drive control bar to stop movement.• Move shift lever to “N” (neutral) position. ENGINE • Move throttle control to “STOP” posi...

9 OPERATION FIG. 12 TURNING • Release the drive control bar.• Move throttle control to “SLOW” position.• Place shift lever indicator in “F” (forward) position. Tines will not turn. • Lift handle to raise tines out of ground.• Swing the handle in the opposite direction you wish to turn, being careful...

10 OPERATION FIG. 14 3 2 1 5 4 6 7 FIG. 13 TILLING HINTS CAUTION: Until you are accustomed to handling your tiller, start actual fi eld use with throttle in slow position (mid-way between “FAST” and “IDLE”). • Tilling is digging into, turning over, and breaking up packed soil before planting. Loose,...

11 OPERATION FIG. 16 OUTER VIEW OF TIRE ADJUST WHEELS FOR CULTIVATING (See Figs. 16 and 17) • Place blocks under right hand side of tiller and remove hairpin clip and clevis pin from right hand wheel. • Move wheel outward approximately 1 inch (2.5 cm) until hole in inner wheel hub lines up with inne...

12 MAINTENANCE GENERAL RECOMMENDATIONS The warranty on this tiller does not cover items that have been subjected to operator abuse or negligence. To receive full value from the warranty, the operator must main tain tiller as instructed in this manual. Some adjustments will need to be made periodical...

13 MAINTENANCE FIG. 18 Disconnect spark plug wire before performing any maintenance (except car bu re tor adjustment) to prevent accidental start ing of engine. Prevent fi res! Keep the engine free of grass, leaves, spilled oil, or fuel. Re move fuel from tank before tipping unit for maintenance. Cl...

14 MAINTENANCE MUFFLER Do not operate tiller without muffl er. Do not tamper with exhaust system. Damaged muffl ers or spark arresters could create a fi re hazard. Inspect pe ri odi cally and re place if nec es sary. If your engine is equipped with a spark arrester screen assembly, re move every 50 ...

15 TILLER TO ADJUST HANDLE HEIGHT (See Fig. 22) Select handle height best suited for your tilling conditions. Handle height will be different when tiller digs into soil.• First loosen handle lock lever.• Handle can be positioned at different settings between “HIGH” and “LOW” positions. • Retighten h...

16 SERVICE AND ADJUSTMENTS FIG. 26 TINE REPLACEMENT (See Figs. 24, 25 and 26) CAUTION: Tines are sharp. Wear gloves or other protection when han- dling tines. A badly worn tine causes your tiller to work harder and dig more shallow. Most important, worn tines cannot chop and shred organic matter as ...

17 SERVICE AND ADJUSTMENTS TO REPLACE GROUND DRIVE BELT (See Figs. 27 and 28) • Remove belt guard as described in “TO REMOVE BELT GUARD”. • Remove old belt by slipping off engine pulley fi rst then remove from transmission pulley. • Place new belt in groove of transmission pulley and into engine pul...

18 SERVICE AND ADJUSTMENTS ENGINE TO ADJUST THROTTLE CONTROL CA BLE (See Fig. 29) The throttle control has been preset at the factory and ad just ment should not be necessary. If adjustment is necessary, proceed as follows:• With engine not running, move remote throttle control lever to “FAST” posit...

19 Immediately prepare your tiller for storage at the end of the season or if the unit will not be used for 30 days or more. WARNING: Never store the tiller with gasoline in the tank inside a build ing where fumes may reach an open fl ame or spark. Allow the engine to cool before storing in any en c...

20 Will not start 1. Out of fuel. 1. Fill fuel tank. 2. Engine not “CHOKED” properly. 2. See “TO START ENGINE” in Operation section. 3. Engine fl ooded. 3. Wait several minutes before attempting to start. 4. Dirty air cleaner. 4. Clean or replace air cleaner cartridge. 5. Water in fuel. 5. Drain fue...

21 KEY PART NO. NO. DESCRIPTION KEY PART NO. NO. DESCRIPTION 1 175769 Control, Throttle2 150744 Grip, Handle4 159227 Bar, Control8 71191008 Screw, Pan Hd. #10-2410 8389J Grip, Handle11 4497H Clip, Hairpin15 108281X Rod, Shift16 72110608 Bolt, Carriage 3/8-16 x 1 Gr. 517 109229X Lock, Handle18 736806...

23 5 10 7 8 9 11 12 13 15 14 KEY PART NO. NO. DESCRIPTION KEY PART NO. NO. DESCRIPTION 5 102332X Bracket, Reinforcement7 102173X Counter Weight, R.H.8 10040600 Washer, Lock 3/89 73220600 Nut, Hex 3/8-1610 74760524 Bolt, Hex 5/16-18 x 1-1/211 4497H Clip, Hair pin12 126875X Rivet, Drilled 13 102190X T...

24 29 102134X Chain #35-50 Pitch30 150737 Ground Shaft Assembly31 143008 Bearing, Shaft, Ground Drive32 106388X Spacer 0.70 x 1.00 x 1.15033 102121X Sprocket and Gear Assembly34 102112X Shaft, Re duc tion (2nd)35 102101X Screw, Whiz, Lock 5/16-18 x 3-1/236 154355 Sprocket Assembly w/Bearing (In- clu...

25 KEY PART NO. NO. DESCRIPTION 2 29 29 15 1 11 11 12 12 13 14 14 24 23 26 27 11 12 16 11 12 25 33 32 16 3 4 7 8 9 5 23 23 28 24 18 6 5 5 12 11 10 tine_shield_13_in(sears) 22 21 20 19 1 KEY PART NO. NO. DESCRIPTION 1 73900500 Nut, Flange 5/16-182 161415X550 Shield, Side, Outer L. H.3 8393J Pin, Stak...

26 KEY PART NO. NO. DESCRIPTION 8 74610616 Bolt, Hex 3/8-24 x 19 4460J Tine, Outer, R.H. 10 132728 Assembly, Hub and Plate, R.H.11 6555J Tine, Inner, R.H. KEY PART NO. NO. DESCRIPTION 1 4459J Tine, Outer, L.H.2 132673 Clevis Pin3 6554J Tine, Inner, L.H.4 3146R Clip, Hairpin5 132727 Assembly, Hub and...

27 KEY PART NO. NO. DESCRIPTION 1 162846 Decal, Logo3 186761 Decal, Logo4 143678 Decal, Instruction, Tilling5 141907 Decal, Hand Placement 6 102180X Decal, Shift Indicator9 141906 Decal, Warning, Rotating Tines10 156199 Deal, Reverse12 162215 Decal, Tine Shield Wrng Dom - - 186100 Manual, Owner's (E...

LIMITED WARRANTY The Manufacturer warrants to the original consumer purchaser that this product as manufactured is free from de-fects in materials and work man ship. For a period of two (2) years from date of purchase by the original consumer purchaser, we will repair or replace, at our option, with...