Weber 43267 - Manuals

5 5 oR ParTs lisT s-660 ™ s-460 ™ www.wEBEr.COM ® Lid - 1 Cookbox - 1 Lid - 1 Cookbox - 1 front frame rail - 1 rear frame rail - 1 rear Panel assembly - 1 bottom Shelf - 1 Left door - 1 right door - 1 warming rack - 1 right Enclosure Panel - 1 Left Enclosure Panel - 1 front Vent Panel - 1 rear Vent ...

7 7 1 2 A door Stop bracket (a) should be positioned as shown. assEMBlY m attEntion! do not attach rear support screws and washers until Step #6. www.wEBEr.COM ®

8 m attEntion! do not fully tighten screws. Clips should slide freely when installed. assEMBlY 3 4 www.wEBEr.COM ®

11 11 m CaUtion: Use two people to lift and install the Summit ® built-in frame assembly. a) Lift the frame assembly into the “island” structure opening. Make sure the frame is resting level on the finished surface of the structure. b) Adjust the Front Vent to rest squarely on ground. 1 1 1 1 1 1 a ...

12 S-460™ S-660™ 1/4" (6.35 mm) drill bit assEMBlY 9 10 www.wEBEr.COM ®

13 13 1 A a) Apply a bead of silicone sealant (1) around the perimeter and front edges of the grill that are in contact with the “island” structure. This will prevent moisture seepage. The sealant you use must have a temperature rating above 120°F (48.8° C). m attEntion! before applying any silicone...

17 17 S-460™ S-660™ C A B match holder assEMBlY 18 www.wEBEr.COM ®

24 bUiLt-in gaS LinE LoCationS Note: Leave an access in the “island” structure for gas supply and regulator service that is not inside the grill structure. Note: Area should be kept clear of sharp, jagged, or extremely abrasive surfaces to avoid possible damage to gas supply lines. Exercise caution ...

25 25 table 6.2(a) maximum Capacity of metallic Pipe in Cubic feet of gas per hour for gas Pressures of 2 psi or Less and a Pressure drop of 0.3 inch water Column. (based on a 0.60 Specific gravity gas) nominal iron Pipe Size (inches) actual id: (inches) Length of Pipe (feet) 10 20 30 40 50 60 70 80...

26 Gas sUPPlY tYPiCaL 20 LP ProPanE gaS SUPPLY inStaLLation The remote tank enclosure kit provided with your Weber Built-In grill shall be used for installations using a 20 lb LP cylinder, mounted in an “island” structure.The remote tank enclosure shall house the included hose and regulator assembly...

27 27 oPErating m warning: only use the weber ® tank Enclosure Kit outdoors in a well-ventilated area. do not use in a garage, building, breezeway or any other enclosed area. m warning: Your weber ® tank Enclosure Kit shall not be used under an unprotected combustible roof or overhang. m warning: Yo...

28 LoCating YoUr LP tanK EnCLoSUrE Kit When determining a suitable location for your LP Tank Enclosure Kit installation, give attention to concerns such as proximity to traffic paths, and keeping any gas supply lines as short as possible. Never locate the Summit ® LP Tank Enclosure Kit in a garage, ...

29 29 4 8 4 2 4 2 2 hose and regulator - 1 tank stand - 1 tank stand base - 1 tank Scale - 1 1/4-20 nut - 6 nylon washer - 12 1/4-20 x 1/2” bolt - 6 Cylinder glide - 2 1/2” flare gasket - 2 3/8” flare gasket - 2 ParTs lisT / assEMBlY 1 2 www.wEBEr.COM ®

30 moUnting thE LP tanK braCKEt Mount the LP tank bracket to the right hand side of the enclosure opening using non corrosive hardware. Mounting holes are provided on the sides and bottom of your LP tank bracket. Be sure to mount the bracket securley to the enclosure before use. moUnting hardwarE no...

31 31 C A B D E 1 ii i iv v ConnECt gaS SUPPLY A 58 inch (147.32 cm) corrugated gas line is supplied with the grill. This line needs to pass through the gas inlet opening to the main gas supply. 1) Connect the corrugated gas line to the manifold located on the right hand side of grill under the cont...

VEntiLation m warning: Ventillation holes must be provided in the structure at the top and bottom to provide ventilation in the event of a gas leak. Ventilation holes can be located in a low visibility area and should be protected by screening material to prevent rodents and insects from entering th...