Weber 3400 NG - Manuals - manualsarea.com

Page 2 - Figure 1; DANGER; Do not use an open flame to check for gas; INSTALL GAS SUPPLY; Typical natural gas supply installation. Figure 1.

2 Gas line piping ■ If the length of line required does not exceed 50 feet,use a 5/8" O.D. tube. One size larger should be usedfor lengths greater than 50 feet. ■ Gas piping may be copper tubing, type K or L;polyethylene plastic tube, with a minimum wallthickness of .062 inch; or standard weight...

Page 3 - Figure 2

3 TOOLS NEEDED Phillips screwdriver 7/16 inch or adjustable wrench SUPPLIES NEEDED While we give much attention to our products, unfor-tunately an occasional error may occur. If a part ismissing, do not go back to the store. Call the WeberCustomer Service Center toll free 1-800-446-1071 toreceive im...

Page 4 - Figure 3

REMOVE GRILL FROMLOWER PACKAGING Make sure natural gas hose is free from lower packagingbefore lifting. WARNING: Lifting the barbecue from the lowerpackaging requires at least two people. With two people lift straight up and over lower packagingand cardboard support. Note: For the Platinum Series II...

Page 5 - Put the foil drip pan into the catch pan.; Figure 4

5 INSTALLATION OF CATCHPAN INTO BOTTOM TRAY Hook the ends of the catch pan holder into the hole in thebottom tray. Figure 4. The front of the catch pan holdermust be on the same side as the finger grip of thebottom tray. Slide the bottom tray onto the mounting rails under thecooking box with finger ...

Page 7 - Figure 9

7 INSTALL WARM-UPBASKET Insert one end of the Warm-Up Basket into the hole in theright end of the lid and the other end into the slot in theleft end of the lid. Figure 9. Figure 9 If you have the Platinum Series II2200, go to step “Install WorkSurfaces” on page 8. If you have the Platinum Series II3...

Page 8 - FOR THE PLATINUM SERIES II 2200; FOR THE PLATINUM SERIES II 3200

8 INSTALL WORKSURFACES FOR THE PLATINUM SERIES II 2200 You will need...left work surface, right work surface, four1/4-20 x 1/2 inch bolts, four nylon washers and a 7/16inch or adjustable wrench. Insert the left work surface tabs in the slots to the left ofthe cooking box. Figure 10 (a). Slip washers...

Page 9 - Check that the side burner is properly assembled.

9 Route the side burner hose around the tank panel so itwill not interfere with the scale indicator rod. The side burner hose is connected in the followingmanner: Slide back the collar of the quick disconnect on themanifold. Push the male fitting of the side burner hoseinto the quick disconnect, and...

Page 12 - INSTALL BOTTOM RACK

12 Valves are shipped in the OFF position, but you shouldcheck to be sure. Put the knob on each valve. Check bypushing down and turning clockwise. Figure 22. Figure 22 For models 3200 & 3400, check that the side burner valve is in the OFF position. Push in and turn to OFF.Figure 23. Figure 23 IN...

Page 13 - CHECK FOR GAS LEAKS; This gas connections of your Weber Gas; Remove the knobs from the control panel. Figure 24.; Do not use an open flame to check for; WARNING; Make sure all burner control knobs are in

13 CHECK FOR GAS LEAKS Figure 25 Figure 24 Use a Phillips screwdriver to remove the screws from theunderside of the control panel. Figure 25. Stand at the right end of the barbecue. Lift the controlpanel off. The side burner or work surface remains in place. View from right underside WARNING This ga...

Page 14 - b) Manifold to side burner hose connection.

14 CHECK FOR GAS LEAKS Figure 26 (a) (b) (c) (d) (e) View from below (f) WARNING: Do not ignite burners while checking for leaks. Check for leaks by wetting the connections with the soapand water solution and watching for bubbles. If bubblesform or if a bubble grows there is a leak. Check: a) Hose t...

Weber 3400 NG - Manuals

Manuals:

Manual Weber 3400 NG

Summary

Weber Manuals