Weber 3200 LP - Manuals - manualsarea.com

Page 2 - Figure 1

2 TOOLS NEEDED Phillips screwdriver 7/16 inch or adjustable wrench SUPPLIES NEEDED While we give much attention to our products, unfor-tunately an occasional error may occur. If a part ismissing, do not go back to the store. Call the WeberCustomer Service Center toll free 1-800-446-1071 toreceive im...

Page 3 - Figure 2

3 REMOVE GRILL FROMLOWER PACKAGING WARNING: Lifting the barbecue from the lowerpackaging requires at least two people. With two people lift straight up and over lower packagingand cardboard support. Note: For the Platinum Series II 3400, make sure the frontdoors are securely closed before lifting. F...

Page 4 - Figure 3

4 INSTALLATION OF CATCHPAN INTO BOTTOM TRAY Slide the bottom tray onto the mounting rails under thecooking box with finger grip toward you. CAUTION: Do not line bottom tray with aluminum foil.It can cause grease fires by trapping the grease andnot allowing grease to flow into the catch pan. Put the ...

Page 6 - SET LP FUEL SCALE; Figure 9; FILL LP TANK; IMPROPER FILLING IS DANGEROUS.

6 SET LP FUEL SCALE You will need: LP tank (empty). Note - For accuracy, the fuel scale must be set with anempty tank. We utilize various LP tank manufacturers. Some of thetanks we receive have differing top collar assemblies.(The top collar is the metal protective ring around thevalve.) One series ...

Page 7 - GENERAL TANK INFORMATION; LP Tank Manufacturer

7 GENERAL TANK INFORMATION LP Tank Manufacturer The LP tank manufacturer is responsible for the materials,workmanship and performance of the tank. If the tank hasa defect, malfunctions, or you have a question regardingthe tank, call the tank manufacturer's customer servicecenter. The phone number is...

Page 8 - FOR THE PLATINUM SERIES II 2200

8 INSTALL WORKSURFACES FOR THE PLATINUM SERIES II 2200 You will need...left work surface, right work surface, four1/4-20 x 1/2 inch bolts, four nylon washers and a 7/16inch or adjustable wrench. Insert the left work surface tabs in the slots to the left ofthe cooking box. Figure 11 (a). Slip washers...

Page 9 - FOR THE PLATINUM SERIES II 3200

9 INSTALL WORK SURFACEAND SIDE BURNER FOR THE PLATINUM SERIES II 3200 You will need... left work surface, side burner assembly,four 1/4-20 x 1/2 inch bolts, four nylon washers and a7/16 inch or adjustable wrench. Insert the left work surface tabs in the slots to the left ofthe cooking box. Figure 12...

Page 12 - FOR THE PLATINUM SERIES II 3400

12 Route the side burner hose around the tank panel so itwill not interfere with scale indicator rod. The side burner hose is connected in the followingmanner: Slide back the collar of the quick disconnect on themanifold. Push the male fitting of the side burner hoseinto the quick disconnect, and ma...

Page 13 - INSTALL BOTTOM RACK

13 INSTALL BOTTOM RACK Figure 22 Place the bottom rack between the frame supports. Figure 22. For the Platinum Series II 3400, place the bottom rackunder the cart between the frame supports. Lift up oneend of the rack so it clears the crosspiece. Continue to liftuntil the opposite end clears the opp...

Page 14 - CONNECT FILLED LP TANK

14 CONNECT FILLED LP TANK WARNING: Make sure that the LP tank valve isclosed. Close by turning clockwise. Hook the LP tank onto the fuel scale. Loosen the tanklock wing nut. Swing the tank lock down. Tighten the wingnut. Figure 25. Figure 25 Tank lock wing nut Remove the tape and packaging from the ...

Page 15 - CHECK FOR GAS LEAKS; The gas connections of your Weber Gas; DANGER; Do not use an open flame to check for; WARNING; Make sure all burner control knobs are in

15 CHECK FOR GAS LEAKS WARNING The gas connections of your Weber Gas Barbecue have been factory tested. We dohowever recommend that you leak check allgas connections before operating yourWeber Gas Barbecue. Remove the knobs from the control panel. Figure 27. Figure 28 Figure 27 Use a Phillips screwd...

Weber 3200 LP - Manuals

Manuals:

Manual Weber 3200 LP

Summary

Weber Manuals