Vivotek IP8130 - Manuals

VIVOTEK User's Manual - 5 Read Before Use The use of surveillance devices may be prohibited by law in your country� The Network Camera is not only a high-performance web-ready camera but can also be part of a flexible surveillance system� It is the user’s responsibility to ensure that the operation ...

VIVOTEK 6 - User's Manual Physical Description Front Panel Status LED Lens Microphone IP8130W IP8131W Microphone IR LEDs Status LED MicroSD/SDHC/SDXC Card Slot Lens WPS WPS button (wireless models) Item LED status Description LED Definitions 1 Steady Red Powered on, during system boot, or indicating...

VIVOTEK User's Manual - 7 Rear Panel The back panels are identical for all models. 1 DI- 2 DI+ 3 Audio GND 4 Audio Out Audio out cable is user-supplied� Power Cord Socket Reset Button Ethernet 10/100 RJ45 Socket General I/O Terminal Block Antenna Connector (for wireless models)

VIVOTEK 8 - User's Manual Install Camera to Stand IMPORTANT: 0002D10766AD IP8130W Record the MAC address before installing the camera� Attach the camera to stand and orient the shooting angle. If preferred, use the included screws to secure the the camera stand to a mounting surface�

VIVOTEK User's Manual - 9 Digital Input Diagram Please refer to the following illustration for the connection method� 3.3V Digital input DI+ DI-: Ground DI- Max. voltage: 40V Connect a digital input device to the input pins of the camera� From the Applications > Digital Input page, you can let ca...

VIVOTEK 10 - User's Manual Hardware Reset The reset button is used to reset the system or restore the factory default settings� Sometimes resetting the system can return the camera to normal operation� If the system problems remain after reset, restore the factory settings and install again. Reset: ...

VIVOTEK User's Manual - 11 Network Deployment 1. If you have external devices such as sensors and alarms, make connections from general I/O terminal block� LAN Connection 3� Connect the supplied power cable from the camera to a power outlet� 2� Connect the camera to a switch via Ethernet cable or di...

VIVOTEK 12 - User's Manual Internet connection via a router Before setting up the Network Camera over the Internet, make sure you have a router and follow the steps below� 1. Connect your Network Camera behind a router, the Internet environment is illustrated below. Regarding how to obtain your IP a...

VIVOTEK User's Manual - 13 Internet connection with static IP Choose this connection type if you are required to use a static IP for the Network Camera� Please refer to LAN setting on page 59 for details� Configure the router, virtual server or firewall, so that the router can forward any data com- ...

VIVOTEK 14 - User's Manual Software Installation Installation Wizard 2 (IW2), free-bundled software included on the product CD, helps you set up your Network Camera on the LAN� 1� Install IW2 under the Software Utility directory from the software CD� Double-click the IW2 shortcut on your desktop to ...

VIVOTEK User's Manual - 15 Ready to Use 1� A browser session with the Network Camera should prompt as shown below� 2� You should be able to see live video from your camera� You may also install the 32-channel recording software from the software CD in a deployment consisting of multiple cameras� For...

VIVOTEK 16 - User's Manual Accessing the Network Camera This chapter explains how to access the Network Camera through web browsers, RTSP players, 3GPP-compatible mobile devices, and VIVOTEK recording software. Using Web Browsers Use Installation Wizard 2 (IW2) to access the Network Cameras on LAN� ...

VIVOTEK User's Manual - 17 ► By default, the Network Camera is not password-protected. To prevent unauthorized access, it is highly recommended to set a password for the Network Camera� For more information about how to enable password protection, please refer to Security on page 77� ► If you see a ...

VIVOTEK 18 - User's Manual • Currently the Network Camera utilizes 32-bit ActiveX plugin� You CAN NOT open a management/view session with the camera using a 64-bit IE browser� • If you encounter this problem, try execute the Iexplore.exe program from C:\Windows\ SysWOW64� A 32-bit version of IE brow...

VIVOTEK User's Manual - 19 WPS WPS 1� Make sure your AP (Access Point) and Operating System support WPS (Wi-Fi Protected Setup) functions� WPS enables easy setup with compatible APs� 2. Disconnect your LAN cable, and connect the power cord.3� Wait for 1 minute for the camera to boot up� Press the WP...

VIVOTEK 20 - User's Manual Wireless Connection: Manual Configuration 1. In addition to the use of WPS function, you can also use a wired connection to manually set up your wireless configuration. 2� Enter the Configuration > Wireless > WLAN page� Key in the same wireless settings as those on y...

VIVOTEK User's Manual - 21 Using RTSP Players To view the MPEG-4 streaming media using RTSP players, you can use one of the following players that support RTSP streaming� Quick Time Player VLC VLC media player mpegable Player pvPlayer As most ISPs and players only allow RTSP streaming through port n...

VIVOTEK 22 - User's Manual Using 3GPP-compatible Mobile Devices To view the streaming media through 3GPP-compatible mobile devices, make sure the Network Camera can be accessed over the Internet� For more information on how to set up the Network Camera over the Internet, please refer to Setup the Ne...

VIVOTEK User's Manual - 23 Using VIVOTEK Recording Software The product software CD also contains an ST7501 recording software, allowing simultaneous monitoring and video recording for multiple Network Cameras� Please install the recording software; then launch the program to add the Network Camera ...

VIVOTEK 24 - User's Manual Main Page This chapter explains the layout of the main page� It is composed of the following sections: VIVOTEK INC. Logo, Host Name, Camera Control Area, Configuration Area, Menu, and Live Video Window� VIVOTEK INC. Logo Click this logo to visit the VIVOTEK website� Host N...

VIVOTEK User's Manual - 25 Configuration Area Client Settings: Click this button to access the client setting page. For more information, please refer to Client Settings on page 29� Configuration: Click this button to access the configuration page of the Network Camera. It is suggested that a passwo...

VIVOTEK 26 - User's Manual Global View: Click on this item to display the Global View window� The Global View window contains a full view image (the largest frame size of the captured video) and a floating frame (the viewing region of the current video stream). The floating frame allows users to con...

VIVOTEK 28 - User's Manual Go to If you configured and chose to display a smaller region of interest from out of a maximum image frame, you can configure different areas within the frame as preset points, and use this menu to move to a location�

VIVOTEK User's Manual - 29 Client Settings This chapter explains how to select the stream transmission mode and saving options on the local computer. When completed with the settings on this page, click Save on the page bottom to enable the settings� H.264 Media Options Select to stream video or aud...

VIVOTEK 30 - User's Manual MP4 Saving Options Users can record live video as they are watching it by clicking Start MP4 Recording on the main page. Here you can specify the storage destination and file name. Folder: Specify a storage destination for the recorded video files. File name prefix: Enter ...

VIVOTEK User's Manual - 31 Joystick settings Enable Joystick Connect a joystick to a USB port on your management computer� Supported by the plug-in (Microsoft’s DirectX), once the plug-in for the web console is loaded, it will automatically detect if there is any joystick on the computer� The joysti...

VIVOTEK 32 - User's Manual Buttons Configuration Click the Configure Buttons button, a window will prompt as shown below. Please follow the steps below to configure your joystick buttons: 1� Select a button number from the Button # pull-down menu� 2. Select a corresponding action, such as Patrol or ...

VIVOTEK 34 - User's Manual Advanced Mode Each function on the configuration list will be explained in the following sections. Those functions that are displayed only in Advanced Mode are marked with Advanced Mode � If you want to set up advanced functions, please click [Advanced Mode] on the bottom ...

VIVOTEK User's Manual - 35 System time Keep current date and time: Select this option to preserve the current date and time of the Network Camera� The Network Camera’s internal real-time clock maintains the date and time even when the power of the system is turned off� Synchronize with computer time...

VIVOTEK 36 - User's Manual System > Homepage layout Advanced Mode This section explains how to set up your own customized homepage layout� General settings This column shows the settings of your hompage layout� You can manually select the background and font colors in Theme Options (the second ta...

VIVOTEK User's Manual - 37 Theme Options Here you can change the color of your homepage layout� There are three types of preset patterns for you to choose from� The new layout will simultaneously appear in the Preview filed. Click Save to enable the settings� Font Color of the Video Title Background...

VIVOTEK User's Manual - 39 System > Logs Advanced Mode This section explains how to configure the Network Camera to send the system log to a remote server as backup� Log server settings Follow the steps below to set up the remote log: 1� Select Enable remote log � 2. In the IP address text box, e...

VIVOTEK 40 - User's Manual PC running ST7501 Recording Software Internet VIVOTEK Network Cameras 3G Cell phone Cell phone Short message Email GSM Modem HTTP PTZ Digital output You can install the included ST7501 recording software, which provides an Event Management function group for delivering eve...

VIVOTEK User's Manual - 41 Access log Access log displays the access time and IP address of all viewers (including operators and administrators) in a chronological order� The access log is stored in the Network Camera’s buffer area and will be overwritten when reaching a certain limit� System > P...

VIVOTEK 42 - User's Manual System > Maintenance This chapter explains how to restore the Network Camera to factory default, upgrade firmware version, etc. General settings > Upgrade firmware This feature allows you to upgrade the firmware of your Network Camera� It takes a few minutes to compl...

VIVOTEK User's Manual - 43 General settings > Restore This feature allows you to restore the Network Camera to factory default settings� Network: Select this option to retain the Network Type settings (please refer to Network Type on page 59)� Daylight Saving Time: Select this option to retain th...

VIVOTEK 44 - User's Manual 3. Open the file with Microsoft ® Notepad and locate your time zone; set the start and end time of DST� When completed, save the file. In the example below, DST begins each year at 2:00 a.m. on the second Sunday in March and ends at 2:00 a.m. on the first Sunday in Novembe...

VIVOTEK User's Manual - 45 The following message is displayed when attempting to upload an incorrect file format. Export language file: Click to export language strings� VIVOTEK provides nine languages: English, Deutsch, Español, Français, Italiano, 日本語, Português, 簡体中文 , and 繁體中文 � Update custom la...

VIVOTEK 46 - User's Manual Media > Image Advanced Mode This section explains how to configure the image settings of the Network Camera� It is composed of the following four columns: General settings, Image settings, Exposure, and Privacy mask� General settings Video title: Enter a name that will ...

VIVOTEK 48 - User's Manual Image settings On this page, you can tune the White balance, Image adjustment and low light compensation. White balance: Adjust the value for the best color temperature� ■ You may follow the steps below to adjust the white balance to the best color temperature. 1. Place a ...

VIVOTEK User's Manual - 49 Exposure Advanced Mode On this page, you can set the Measurement window, Exposure level, Exposure time, and Gain control settings. Detailed configurations will be automatically adjusted since the sensor library will automatically adjust the value according to the ambient l...

VIVOTEK 50 - User's Manual Measurement Window: This function allows user to set measurement window(s) for low light compesation�■ Full view: Calculate the full range of view and offer appropriate light compesation� ■ BLC (Back Light Compensation): This option allows you to use the center of the curr...

VIVOTEK User's Manual - 51 You can click Restore to recall the original settings without incorporating the changes� When completed with the settings on this page, click Save to enable the settings� If you want to configure another sensor setting for the schedule mode, please click Profile to open th...

VIVOTEK 52 - User's Manual Privacy mask Advanced Mode Click Privacy Mask to open the settings page. On this page, you can block out sensitive zones to address privacy concerns� ■ To set the privacy mask windows, follow the steps below: 1� Click New to add a new window� 2. You can use the mouse curso...

VIVOTEK User's Manual - 53 Media > Video Stream settings This Network Camera supports multiple streams with a frame size ranging from 176 x 144 to 1280 x 800� The definition of multiple streams: ■ Stream 1: Users can define the "Region of Interest" (viewing region) and the "Output Fra...

VIVOTEK User's Manual - 55 Click the stream item to display the detailed information. If configured, the maximum frame size will be in accordance with your settings in the Viewing Window sections� This Network Camera provides real-time H�264 and MJPEG compression standards (Dual Codec) for real-time...

VIVOTEK 56 - User's Manual The frame rate will decrease if you select a higher resolution� ■ Intra frame period Determine how often to plant an I frame. The shorter the duration, the more likely you will get better video quality, but at the cost of higher network bandwidth consumption. Select the in...

VIVOTEK User's Manual - 57 If JPEG mode is selected, the Network Camera sends consecutive JPEG images to the client, producing a moving effect similar to a filmstrip. Every single JPEG image transmitted guarantees the same image quality, which in turn comes at the expense of variable bandwidth usage...

VIVOTEK 58 - User's Manual Media > Audio Audio Settings Mute: Select this option to disable audio transmission from the Network Camera to all clients� Note that if muted, no audio data will be transmitted even if audio transmission is enabled on the Client Settings page. In that case, the followi...

VIVOTEK User's Manual - 59 Network > General settings This section explains how to configure a wired network connection for the Network Camera. Network Type LAN Select this option when the Network Camera is deployed on a local area network (LAN) and is intended to be accessed by local computers� ...

VIVOTEK 62 - User's Manual 4. In the Networking Services dialog box, select Universal Plug and Play and click OK � 5� Click Next in the following window� 6� Click Finish � UPnP TM is enabled� ► How does UPnP TM work? UPnP TM networking technology provides automatic IP configuration and dynamic disco...

VIVOTEK User's Manual - 63 Enable IPv6 Select this option and click Save to enable IPv6 settings� Please note that this only works if your network environment and hardware equipment support IPv6� The browser should be Microsoft ® Internet Explorer 6.5, Mozilla Firefox 3.0 or above. When IPv6 is enab...

VIVOTEK User's Manual - 65 Port HTTPS port: By default, the HTTPS port is set to 443. It can also be assigned to another port number between 1025 and 65535� FTP port: The FTP server allows the user to save recorded video clips� You can utilize VIVOTEK's Installation Wizard 2 to upgrade the firmware ...

VIVOTEK 66 - User's Manual 2013/06/09 17:08:56 Audio is being transmitted to the Network Camera Mute Mic Volume Talk Button Click to enable audio transmission to the Network Camera; click to adjust the volume of microphone; click to turn off the audio. To stop talking, click again� FTP port: The FTP...

VIVOTEK User's Manual - 67 Network > Streaming protocols Advanced Mode HTTP streaming To utilize HTTP authentication, make sure that your have set a password for the Network Camera first; please refer to Security > User account on page 77 for details� Authentication: Depending on your network ...

VIVOTEK 68 - User's Manual URL command -- http://<ip address>:<http port>/<access name for stream 1 or 2> For example, when the Access name for stream 2 is set to video2�mjpg : 1� Launch Mozilla Firefox� 2� Enter the above URL command in the address bar� Press Enter � 3� The JPEG i...

VIVOTEK User's Manual - 69 Authentication: Depending on your network security requirements, the Network Camera provides three types of security settings for streaming via RTSP protocol: disable, basic, and digest. If basic authentication is selected, the password is sent in plain text format, but th...

VIVOTEK User's Manual - 71 Network > DDNS This section explains how to configure the dynamic domain name service for the Network Camera. DDNS is a service that allows your Network Camera, especially when assigned with a dynamic IP address, to have a fixed host and domain name. Express link Expres...

VIVOTEK 72 - User's Manual Manual setup DDNS: Dynamic domain name service Enable DDNS: Select this option to enable the DDNS setting� Provider: Select a DDNS provider from the provider drop-down list� VIVOTEK offers Safe100.net , a free dynamic domain name service, to VIVOTEK customers. It is recomm...

VIVOTEK 74 - User's Manual Network > SNMP (Simple Network Management Protocol) This section explains how to use the SNMP on the network camera� The Simple Network Management Protocol is an application layer protocol that facilitates the exchange of management information between network devices� ...

VIVOTEK User's Manual - 75 Wireless > WLAN (IP8130W and IP8131W) Although the wireless connection is made before you can access the camera’s configuration page, you can enter the WLAN settings if configuration change should be made, e.g., connecting to a different AP. Below are more information a...

VIVOTEK User's Manual - 77 Security > User Account This section explains how to enable password protection and create multiple accounts� Root Password The administrator account name is “root”, which is permanent and can not be deleted. If you want to add more accounts in the Manage User column, p...

VIVOTEK 78 - User's Manual Security > HTTPS (Hypertext Transfer Protocol over SSL) This section explains how to enable authentication and encrypted communication over SSL (Secure Socket Layer)� It helps protect streaming data transmission over the Internet on higher security level� Create and Ins...

VIVOTEK 80 - User's Manual Create certificate request and install 1� Select the option from the Method pull-down menu� 2� Click Create certificate to proceed� 3� The following information will show up in a pop-up window after clicking Create � Then click Save to generate the certificate request. 4. ...

VIVOTEK User's Manual - 81 5. Look for a trusted certificate authority, such as Symantec’s VeriSign Authentication Services, that issues digital certificates. Sign in and purchase the SSL certification service. Copy the certificate request from your request prompt and paste it in the CA’s signing re...

VIVOTEK 82 - User's Manual 7. Open a new edit, paste the certificate contents, and press ENTER at the end of the contents to add an empty line� 8. Convert file format from DOS to UNIX. Open File menu > Conversions > DOS to Unix �

VIVOTEK User's Manual - 83 9. Save the edit using the “.crt” extension, using a file name like “CAcert.crt.” 10. Return to the original firmware session, use the Browse button to locate the crt certificate file, and click Upload to enable the certification.

VIVOTEK 84 - User's Manual 11. When the certifice file is successfully loaded, its status will be stated as Active � Note that a certificate must have been created and installed before you can click on the “ Save " button for the configuration to take effect. 12.To begin an encrypted HTTPS sessi...

VIVOTEK User's Manual - 85 Security > Access List Advanced Mode This section explains how to control access permission by verifying the client PC’s IP address� General Settings Maximum number of concurrent streaming connection(s) limited to: Simultaneous live viewing for 1~10 clients (including s...

VIVOTEK 86 - User's Manual ■ Refresh: Click this button to refresh all current connections. ■ Add to deny list: You can select entries from the Connection Status list and add them to the Deny List to deny access� Please note that those checked connections will only be disconnected temporarily and wi...

VIVOTEK User's Manual - 87 Network: This rule allows the user to assign a network address and corresponding subnet mask to the Allow/Deny List� The address and network mask are written in CIDR format� For example: Range: This rule allows the user to assign a range of IP addresses to the Allow/Deny L...

VIVOTEK 88 - User's Manual PTZ > PTZ settings This section explains how to control the Network Camera’s Pan/Tilt/Zoom operation� There are two ways to enable the function: The Digital name tag refers to the e-PTZ operation� It allows users to quickly move the focus to a target area for close-up v...

VIVOTEK User's Manual - 89 Home page in E-PTZ Mode ■ The e-Preset Positions will also be displayed on the home page� Select one from the drop-down list, and the camera’s view area will move to the selected e-preset position� ■ If you have configured different e-preset positions for different streams...

VIVOTEK 90 - User's Manual Patrol settings You can select some preset positions for the Network Camera to patrol� Please follow the steps below to set up a patrol schedule: 1. Select the preset locations on the list, and click � 2� The selected preset locations will be displayed on the Patrol locati...

VIVOTEK User's Manual - 91 NOTE ► The Preset Positions will also be displayed on the home page. Select one from the Go to drop-down list, and the Network Camera will move to the selected preset position. ► Click Patrol: The Network Camera will patrol along the selected positions repeatedly. Please r...

VIVOTEK 92 - User's Manual Event > Event settings This section explains how to configure the Network Camera to responds to particular situations (event). A typical application is that when a motion is detected, the Network Camera sends buffered images to an FTP server or e-mail address as notific...

VIVOTEK User's Manual - 93 ■ Event name: Enter a name for the event setting� ■ Enable this event: Select this option to enable the event setting� ■ Priority: Select the relative importance of this event (High, Normal, or Low). Events with a higher priority setting will be executed first. ■ Detect ne...

VIVOTEK 94 - User's Manual ■ Camera tampering detection This option allows the Network Camera to trigger when the camera detects that is is being tampered with� To enable this function, you need to configure the Tampering Detection option first. Please refer to page 108 for detailed information� 14 ...

VIVOTEK User's Manual - 95 Add server To set an event that will be recorded in videos or snapshots, it is necessary to configure the server and media settings so that the Network Camera will know what action to take (such as which server to send the media files to) when a trigger is activated� Click...

VIVOTEK 96 - User's Manual To verify if the email settings are correctly configured, click Test � The result will be shown in a pop-up window. If successful, you will also receive an email indicating the result. Click Save server to enable the settings� Note that after you set up the first event ser...

VIVOTEK 98 - User's Manual Network storage: Select to send the media files to a network storage location when a trigger is activated� Please refer to NAS server on page 112 for details� Click Save server to enable the settings� ■ SD Test: Click to test your SD card. The system will display a message...

VIVOTEK 100 - User's Manual Add media Click Add media to open the media setting window� You can specify the type of media that will be sent when a trigger is activated. A total of 5 media settings can be configured. There are three choices of media types available: Snapshot, Video Clip, and System l...

VIVOTEK User's Manual - 101 ■ Add date and time suffix to the file name Select this option to add a date/time suffix to the file name. For example: Click Save media to enable the settings� To note that after you set up the first media server, a new column for media server will automatically show up ...

VIVOTEK User's Manual - 103 In the Event settings column, the Servers and Medias you configured will be listed; please make sure the Event -> Status is indicated as ON , in order to enable the event triggering action. When completed, click Save event to enable the settings and click Close to exit...

VIVOTEK 104 - User's Manual Customized Script This function allows you to upload a sample script (.xml file) to the webpage, which will save your time on configuring the settings. Please note that there is a limited number of customized scripts you can upload; if the current amount of customized scr...

VIVOTEK User's Manual - 105 Applications > Motion detection This section explains how to configure the Network Camera to enable motion detection. A total of three motion detection windows can be configured. Follow the steps below to enable motion detection:Follow the steps below to enable motion ...

VIVOTEK 106 - User's Manual A green bar indicates that even though motions have been detected, the event has not been triggered because the image variations still fall under the defined threshold. If you want to configure other motion detection settings for a different time period within a day, plea...

VIVOTEK User's Manual - 107 ► How does motion detection work? There are two motion detection parameters: Sensitivity and Percentage. In the illustration above, frame A and frame B are two sequential images� Pixel differences between the two frames are detected and highlighted in gray (frame C) and w...

VIVOTEK 108 - User's Manual Applications > Digital Input Connect a DI device to the camera's push-in type terminal block, the camera will automatically detect the current connection state as pulled-high or pulled-low� You may then define the triggering condition� Normal status: Select High or Low...

VIVOTEK User's Manual - 109 Recording > Recording settings Advanced Mode This section explains how to configure the recording settings for the Network Camera. Recording Settings NOTE ► Please remember to format your SD card when using it for the first time. Please refer to page 114 for detailed i...

VIVOTEK 110 - User's Manual The alarm trigger includes: motion detection, tampering detection, and DI detection. Please refer to Event Settings on page 92� ■ Pre-event recording and post-event recording The Network Camera has a buffer area (a flash memory); it temporarily holds data up to a certain ...

VIVOTEK 112 - User's Manual If successful, you will receive a test.txt file on the network storage server. 3� Enter a server name� 4� Click Save to complete the settings and click Close to exit the page� Back to the Recording setup page, you can now record videos to the networked storage. ■ Capacity...

VIVOTEK User's Manual - 113 Recording file management ■ Maximum duration (minutes): Specifies the length of each of the recorded videos. ■ Maximum file size: (MB - Megabytes ) : Specifies the file size limitation of each recorded video� The duration and size are the upper thresholds. The limitation ...

VIVOTEK 114 - User's Manual Local storage > SD card management This section explains how to manage the local storage on the Network Camera� Here you can view SD card status, and implement SD card control. SD card staus This column shows the status and reserved space of your SD card� Please rememb...

VIVOTEK User's Manual - 115 Local storage > Content management This section explains how to manage the content of recorded videos on the Network Camera� Here you can search and view the records and view the searched results� Searching and Viewing the Records This column allows the user to set up ...

VIVOTEK 116 - User's Manual Search Results The following is an example of search results. There are four columns: Trigger time, Media type, Trigger type, and Locked. Click to sort the search results in either direction� Numbers of entries displayed on one page Enter a key word to filter the search r...

VIVOTEK User's Manual - 117 ■ Lock/Unlock: Select the desired search results, then click this button. The selected items will become Locked, which will not be deleted during cyclic recording. You can click again to unlock the selections. For example: ■ Select All: The checkbox on top of all entries ...

VIVOTEK 118 - User's Manual Appendix URL Commands for the Network Camera 1. Overview For some customers who already have their own web site or web control application, the Network Camera/Video Server can be easily integrated through URL syntax� This section specifies the external HTTP-based applicat...

VIVOTEK User's Manual - 119 URL Command Document for All SeriesIP8130W/IP8131W 3. General CGI URL Syntax and Parameters When the CGI request includes internal camera parameters, these parameters must be written exactly as they are named in the camera or video server. The CGIs are organized in functi...

VIVOTEK 120 - User's Manual URL Command Document for All SeriesIP8130W/IP8131W 4. Security Level SECURITY LEVEL SUB-DIRECTORY DESCRIPTION 0 anonymous Unprotected. 1 [view] anonymous, viewer, dido, camctrl 1. Can view, listen, talk to camera. 2. Can control DI/DO, PTZ of the camera. 4 [operator] anon...

VIVOTEK User's Manual - 121 URL Command Document for All SeriesIP8130W/IP8131W 5. Get Server Parameter Values Note: The access right depends on the URL directory. Method: GET/POST Syntax:http://< servername >/cgi-bin/anonymous/getparam.cgi?[ <parameter> ] [&<parameter>…] http:/...

VIVOTEK User's Manual - 123 URL Command Document for All SeriesIP8130W/IP8131W 6. Set Server Parameter Values Note: The access right depends on the URL directory. Method: GET/POST Syntax:http://< servername >/cgi-bin/anonymous/setparam.cgi? <parameter>=<value> [&<parameter&g...

VIVOTEK 124 - User's Manual URL Command Document for All SeriesIP8130W/IP8131W Only the parameters that you set and are readable will be returned. Example: Set the IP address of server to 192.168.0.123: Request:http://myserver/cgi-bin/admin/setparam.cgi?network_ipaddress=192.168.0.123 Response:HTTP/...

VIVOTEK User's Manual - 125 URL Command Document for All SeriesIP8130W/IP8131W 7. Available parameters on the server This chapter defines all the parameters which can be configured or retrieved from VIVOTEK network camera or video server. The general format of description is listed in the table belo...

VIVOTEK 126 - User's Manual URL Command Document for All SeriesIP8130W/IP8131W 7.1 system Group: system NAME VALUE DEFAULT SECURITY (get/set) DESCRIPTION hostname string[64] Mega-Pixel NetworkCamera 1/6 Host name of server (Network Camera, Wireless Network Camera, Video Server, Wireless Video Server...

VIVOTEK 128 - User's Manual URL Command Document for All SeriesIP8130W/IP8131W Tbilisi, Yerevan 180: GMT 04:30 Kabul 200: GMT 05:00 Ekaterinburg, Islamabad, Karachi, Tashkent 220: GMT 05:30 Calcutta, Chennai, Mumbai, New Delhi 230: GMT 05:45 Kathmandu 240: GMT 06:00 Almaty, Novosibirsk, Astana, Dhak...

VIVOTEK User's Manual - 129 URL Command Document for All SeriesIP8130W/IP8131W -140,-120, -80,-40,0, 40,41,80, 81,82,83, 120,140, 380,400,480 updateinterval 0, 3600, 86400, 604800, 2592000 0 6/6 0 to Disable automatic time adjustment, otherwise, it indicates the seconds between NTP automatic update ...

VIVOTEK 130 - User's Manual URL Command Document for All SeriesIP8130W/IP8131W restoreexceptlang <Any Value> N/A 7/6 Restore the system parameters to default values except the custom language file the user has uploaded. This command can cooperate with other “restoreexceptXYZ” commands. When co...

VIVOTEK User's Manual - 131 URL Command Document for All SeriesIP8130W/IP8131W server. customlanguage_count <integer> 0 0/6 Number of custom languages which have been uploaded to the server. customlanguage_i<0~(maxcount-1)> string N/A 0/6 Custom language name. 7.2 status Group: status NA...

VIVOTEK 132 - User's Manual URL Command Document for All SeriesIP8130W/IP8131W 7.4 security Group: security NAME VALUE DEFAULT SECURITY (get/set) DESCRIPTION privilege_do view, operator, admin operator 1/6 Indicate which privileges and above can control digital output(capability.ndo > 0) privileg...

VIVOTEK User's Manual - 133 URL Command Document for All SeriesIP8130W/IP8131W change a service port to the port occupied by another service currently. Otherwise, the service may fail. Stopped service will auto-start after changing port settings.Ex:Change HTTP port from 80 to 5556, and change RTP po...

VIVOTEK 134 - User's Manual URL Command Document for All SeriesIP8130W/IP8131W addonrouter <ip address> <blank> 6/6 IPv6 router address. addondns <ip address> <blank> 6/6 IPv6 DNS address. allowoptional <boolean> 0 6/6 Allow manually setup of IP address setting. 7.5.4 F...

VIVOTEK 136 - User's Manual URL Command Document for All SeriesIP8130W/IP8131W and so on. videoport 1025 ~ 65535 5560+n*2 4/4 Multicast video port. audioport 1025 ~ 65535 5562+n*2 4/4 Multicast audio port. (capability.naudio > 0) ttl 1 ~ 255 15 4/4 Mutlicast time to live value. 7.5.8 SIP port Sub...

VIVOTEK User's Manual - 137 URL Command Document for All SeriesIP8130W/IP8131W 0 => allow 1 => deny ipv4list_i<0~9> Single address: <ip address> Networkaddress: <ip address / network mask> Rangeaddress:<start ip address - end ip address> <blank> 6/6 IPv4 address l...

VIVOTEK 138 - User's Manual URL Command Document for All SeriesIP8130W/IP8131W 7.7.1 video input setting per channel Group: videoin_c<0~(n-1)> for n channel products, and m is stream number NAME VALUE DEFAULT SECURITY (get/set) DESCRIPTION whitebalance auto, manual,rbgain auto 4/4 “auto” indic...

VIVOTEK User's Manual - 139 URL Command Document for All SeriesIP8130W/IP8131W Bit 5 => Support focus operation; 0(not support), 1(support) text string[60] <blank> 1/4 Enclose caption. imprinttimestamp <boolean> 0 4/4 Overlay time stamp on video. flickerless <boolean> 0 4/4 Enab...

VIVOTEK 140 - User's Manual URL Command Document for All SeriesIP8130W/IP8131W “ratecontrolmode”. 99,100 is the customized manual input setting. 1 = worst quality, 5 = best quality. s<0~(m-1)>_h264_qpercent 1~100 45 4/4 Set quality by percentage. 1: Worst quality 100: Best quality (s<0~(m-1...

VIVOTEK User's Manual - 141 URL Command Document for All SeriesIP8130W/IP8131W 1: Worst quality 100: Best quality (s<0~(m-1)>_mjpeg_quant = 100) s<0~(m-1)>_forcei 1 N/A 7/6 Force I frame. 7.7.1.1 Alternative video input profiles per channel In addition to the primary setting of video inp...

VIVOTEK 142 - User's Manual URL Command Document for All SeriesIP8130W/IP8131W enableblc <boolean> 0 4/4 Enable backlight compensation. whitebalance auto,manual,rbgain auto 4/4 “auto” indicates auto white balance.“manual” indicates keep current value. “rbgain” indicates using rgain and gbain. ...

VIVOTEK User's Manual - 143 URL Command Document for All SeriesIP8130W/IP8131W 7.9 image setting per channel Group: image_c<0~(n-1)> for n channel products NAME VALUE DEFAULT SECURITY(get/set) DESCRIPTION brightness -5 ~ 5 -5 4/4 Adjust brightness of image according to mode settings. saturatio...

VIVOTEK 144 - User's Manual URL Command Document for All SeriesIP8130W/IP8131W “saturationpercent” contrast -5 ~ 5 0 4/4 Preview of contrast adjustment of image according to mode settings. sharpness -3~3,100 100 4/4 Preview of sharpness adjustment of image according to mode settings. 100 means using...

VIVOTEK User's Manual - 145 URL Command Document for All SeriesIP8130W/IP8131W 7.11 Audio input per channel Group: audioin_c<0~(n-1)> for n channel products (capability.audioin>0) NAME VALUE DEFAULT SECURITY (get/set) DESCRIPTION source linein,micin micin 4/4 micin => use built-in microp...

VIVOTEK 146 - User's Manual URL Command Document for All SeriesIP8130W/IP8131W position. win_i<0~2>_top 0 ~ 240 0 4/4 Top coordinate of window position. win_i<0~2>_width 0 ~ 320 0 4/4 Width of motion detection window. win_i<0~2>_height 0 ~ 240 0 4/4 Height of motion detection windo...

VIVOTEK User's Manual - 147 URL Command Document for All SeriesIP8130W/IP8131W motion detection window. i<0~(m-1)>_win_i<0~2>_objsize 0 ~ 100 0 4/4 Percent of motion detection window. i<0~(m-1)>_win_i<0~2>_sensitivity 0 ~ 100 0 4/4 Sensitivity of motion detection window. 7.14...

VIVOTEK 148 - User's Manual URL Command Document for All SeriesIP8130W/IP8131W <provider>_passwordkey string[64] <blank> 6/6 Your password or key to login to the DDNS service provider. <provider>_servername string[128] <blank> 6/6 The server name for safe100. (This field only...

VIVOTEK User's Manual - 149 URL Command Document for All SeriesIP8130W/IP8131W 7.17 UPnP port forwarding Group: upnpportforwarding NAME VALUE DEFAULT SECURITY (get/set) DESCRIPTION enable <boolean> 0 6/6 Enable or disable the UPnP port forwarding service. upnpnatstatus 0~3 0 6/7 The status of ...

VIVOTEK 150 - User's Manual URL Command Document for All SeriesIP8130W/IP8131W 7.19 SNMP Group: snmp (capability.snmp > 0) NAME VALUE DEFAULT SECURITY(get/set) DESCRIPTION v2 0~1 0 6/6 SNMP v2 enabled. 0 for disable, 1 for enable v3 0~1 0 6/6 SNMP v3 enabled. 0 for disable, 1 for enable secnamerw...

VIVOTEK 152 - User's Manual URL Command Document for All SeriesIP8130W/IP8131W window. 7.22 Capability Group: capability NAME VALUE DEFAULT SECURITY (get/set) DESCRIPTION api_httpversion 0100a 0100a 0/7 The HTTP API version. bootuptime <positive integer> 60 0/7 Server bootup time. nir 0, <p...

VIVOTEK 154 - User's Manual URL Command Document for All SeriesIP8130W/IP8131W Bit 8 => Invalidate bit 1 ~ 7;0(bit 1 ~ 7 are valid), 1(bit 1 ~ 7 are invalid) Bit 9 => Reserved bit; Invalidate lens_pan, Lens_tilt, lens_zoon, lens_focus, len_iris. 0(fields are valid), 1(fields are invalid) windo...

VIVOTEK User's Manual - 155 URL Command Document for All SeriesIP8130W/IP8131W st_backchannel backchannel multicast. protocol_rtp_tcp <boolean> 1 0/7 Indicate whether to support RTP over TCP. protocol_rtp_http <boolean> 1 0/7 Indicate whether to support RTP over HTTP. protocol_spush_mjpe...

VIVOTEK 156 - User's Manual URL Command Document for All SeriesIP8130W/IP8131W 1: Supported camctrl_privilege <boolean> 1 0/7 Indicate whether to support “Manage Privilege” of PTZ control in the Security page.1: support both /cgi-bin/camctrl/camctrl.cgiand/cgi-bin/viewer/camctrl.cgi 0: support...

VIVOTEK User's Manual - 157 URL Command Document for All SeriesIP8130W/IP8131W event/control transfer. joystick <boolean> 1 0/7 Indicate whether to support joystick control. storage_dbenabled <boolean> 1 0/7 Media files are indexed in database. nanystream 0, <positive integer> 0 0/...

VIVOTEK 160 - User's Manual URL Command Document for All SeriesIP8130W/IP8131W action_cf_media 0~4, 101 NULL 6/6 Index of the attached media. action_cf_datefolder <boolean> 1 6/6 Enable this to create folders by date, time, and hour automatically. action_cf_backup <boolean> 0 6/6 Enable ...

VIVOTEK User's Manual - 161 URL Command Document for All SeriesIP8130W/IP8131W email_address string[128] NULL 6/6 Email server address. email_sslmode 0, 1 0 6/6 Enable support SSL. email_port 0~65535 25 6/6 Port to connect to the server. email_username string[64] NULL 6/6 Username to log in to the s...

VIVOTEK User's Manual - 165 URL Command Document for All SeriesIP8130W/IP8131W install manual => Create self-signed certificate manually. install => Create certificate request and install. status -3 ~ 1 0 6/7 Specify the https status. -3 = Certificate not installed -2 = Invalid public key -1 =...

VIVOTEK 166 - User's Manual URL Command Document for All SeriesIP8130W/IP8131W 7.30 Region of interest Group: roi_c<0~(n-1)> for n channel product, and m is the number of streams which support ROI. (capability.eptz > 0) PARAMETER VALUE Default SECURITY (get/set) DESCRIPTION s<0~(m-1)>...

VIVOTEK User's Manual - 167 URL Command Document for All SeriesIP8130W/IP8131W patrolseq string[120] <blank> 1/4 The patrol sequence of ePTZ. All the patrol position indexes will be separated by "," patroldwelling string[160] <blank> 1/4 The dwelling time (unit: second) of each p...

VIVOTEK 168 - User's Manual URL Command Document for All SeriesIP8130W/IP8131W 7.33 wireless Group: wireless (capability.network.wireless > 0) NAME VALUE DEFAULT SECURITY (get/set) DESCRIPTION ssid string[32] default 6/6 SSID for wireless lan settings. The valid characters are [A-Z] [a-z] [0-9] [...

VIVOTEK User's Manual - 169 URL Command Document for All SeriesIP8130W/IP8131W The valid characters are [A-Z] [a-z] [0-9]. key4 password [13] 0000000000 6/6 WEP key4 for encryption. The valid characters are [A-Z] [a-z] [0-9]. domain ‘U’ for USA ‘C’ for Canada ‘E’ for Euro ‘S’ for Spain ‘F’ for Franc...

VIVOTEK 170 - User's Manual URL Command Document for All SeriesIP8130W/IP8131W 8. Useful Functions 8.1 Query Status of the Digital Input (capability.ndi > 0) Note: This request requires Viewer privileges Method: GET/POST Syntax:http://< servername >/cgi-bin/dido/getdi.cgi?[di0][&di1][&a...

VIVOTEK User's Manual - 171 URL Command Document for All SeriesIP8130W/IP8131W 8.2 Capture Single Snapshot Note: This request requires Normal User privileges. Method: GET/POST Syntax:http://< servername >/cgi-bin/viewer/video.jpg?[channel=<value>][&resolution=<value>] [&qua...

VIVOTEK 172 - User's Manual URL Command Document for All SeriesIP8130W/IP8131W 8.3 Account Management Note: This request requires Administrator privileges. Method: GET/POST Syntax:http://< servername >/cgi-bin/admin/editaccount.cgi? method=<value>&username= <name> [&userpas...

VIVOTEK User's Manual - 173 URL Command Document for All SeriesIP8130W/IP8131W 8.4 System Logs Note: This request require Administrator privileges. Method: GET/POST Syntax:http://< servername >/cgi-bin/admin/syslog.cgi Server will return the most up-to-date system log. Return:HTTP/1.0 200 OK\r...

VIVOTEK User's Manual - 175 URL Command Document for All SeriesIP8130W/IP8131W zoom wide Zoom larger view with current speed. tele Zoom further with current speed. zooming wide or tele Zoom without stopping for larger view or further view with zs speed, used for joystick control. zs 0 ~ 6 Set the sp...

VIVOTEK 180 - User's Manual URL Command Document for All SeriesIP8130W/IP8131W 8.11 Get SDP of Streams Note: This request requires Viewer access privileges. Method: GET Syntax:http://< servername >/<network_rtsp_s<0~m-1>_accessname> “m” is the stream number. “network_accessname_<...

VIVOTEK User's Manual - 181 URL Command Document for All SeriesIP8130W/IP8131W 8.13 Storage managements (capability.storage.dbenabled > 0) Note: This request requires administrator privileges. Method: GET and POST Syntax:http://< servername >/cgi-bin/admin/lsctrl.cgi?cmd=<cmd_type>[&a...

VIVOTEK 182 - User's Manual URL Command Document for All SeriesIP8130W/IP8131W isLocked <boolean> Optional. Indicate if the file is locked or not. 0: file is not locked. 1: file is locked. A locked file would not be removed from UI or cyclic storage. triggerTime <text> Optional. Indicate...

VIVOTEK User's Manual - 183 URL Command Document for All SeriesIP8130W/IP8131W Command: update PARAMETER VALUE DESCRIPTION label <integer primary key> Required. Identify the designated record. Ex. label=1 isLocked <boolean> Required. Indicate if the file is locked or not. Ex. Update reco...

VIVOTEK 184 - User's Manual URL Command Document for All SeriesIP8130W/IP8131W OK. Subgroup of stormgr: i<0~(n-1)> : n is the total number of displayed records. Element name Type Description label <Integer Primary Key> A unique integer. triggerType <Text> Indicate the event trigger...

VIVOTEK User's Manual - 185 URL Command Document for All SeriesIP8130W/IP8131W <isLocked> 0 </isLocked> <triggerTime> 2009-01-24 12:00:00 </triggerTime> <backup> 0 </backup> </i0> <i1> <label> 2 </label> <triggerType> di </triggerT...

VIVOTEK User's Manual - 187 URL Command Document for All SeriesIP8130W/IP8131W http:// < servername > /cgi-bin/admin/ jpegtoavi.cgi ?resolution=800x600&fps=1&list=’/mnt/auto/CF/NCMF/video1650.jpg’, ’/mnt/auto/C F/NCMF/video1651.jpg’, ’/mnt/auto/CF/NCMF/video1652.jpg’, 8.14 Virtual inpu...

VIVOTEK 190 - User's Manual URL Command Document for All SeriesIP8130W/IP8131W <product dependent> input setting. 1 = worst quality, 5 = best quality. <product dependent> mjpeg_qvalue 10~200 2~97<product dependent> 50<productdependent> Manual video quality level input.(This m...

VIVOTEK User's Manual - 191 URL Command Document for All SeriesIP8130W/IP8131W 8.17 Export Files Note: This request requires Administrator privileges. Method: GET Syntax:For daylight saving time configuration file: http://< servername >/cgi-bin/admin/exportDst.cgi For language file: http://<...

VIVOTEK 194 - User's Manual Technology License Notice MPEG-4 AAC Technology THIS PRODUCT IS LICENSED UNDER THE MPEG-4 AAC AUDIO PATENT LICENSE� THIS PRODUCT MAY NOT BE DECOMPILED, REVERSE-ENGINEERED OR COPIED, EXCEPT WITH REGARD TO PC SOFTWARE, OF WHICH YOU MAY MAKE SINGLE COPIES FOR ARCHIVAL PURPOS...

VIVOTEK User's Manual - 195 Electromagnetic Compatibility (EMC) FCC Statement This device compiles with FCC Rules Part 15� Operation is subject to the following two conditions�■ This device may not cause harmful interference, and■ This device must accept any interference received, including interfer...