Vivotek FD8361L - Manuals

VIVOTEK User's Manual - 5 Outer View General I/O Terminal Block This Network Camera provides a general I/O terminal block which is used to connect external input / output devices. The pin definitions are described below. Network Camera Model No: FD8361 Made in Taiwan This device complies with part 1...

VIVOTEK 6 - User's Manual Hardware Reset The reset button is used to reset the system or restore the factory default settings� Sometimes resetting the system can return the camera to normal operation� If the system problems remain after reset, restore the factory settings and install again� Reset: P...

VIVOTEK User's Manual - 7 Installation Hardware Installation First, use a screwdriver to loose the three screws and detach the dome cover from the camera base� Then, follow the steps below to install the camera to either a ceiling or a wall� Ceiling mount (with the bottom base) 1� Attach the supplie...

VIVOTEK 8 - User's Manual Wall mount (with the bottom base) 1� Attach the supplied alignment sticker to the wall� 2� Using the 10 circles on the sticker, drill at least 2 pilot holes symmetrically on each side into the wall� Then hammer the four supplied plastic anchors into the holes� 3� Using the ...

VIVOTEK User's Manual - 9 Drop-ceiling mount (without the bottom base) 1� Attach the supplied ceiling hole template sticker to the ceiling� 2� Open a hole along the inner circle of the sticker�3� Using the 3 circles on the sticker, drill 3 pilot holes into the ceiling� Then hammer the three supplied...

VIVOTEK 10 - User's Manual Network Deployment Setting up the Network Camera over the Internet This section explains how to configure the Network Camera to an Internet connection � 1� Connect the power cable to the AC 24V terminal block� 2. Use the supplied RJ45 female/female coupler to connect the N...

VIVOTEK User's Manual - 11 2� In this case, if the Local Area Network (LAN) IP address of your Network Camera is 192�168�0�3, please forward the following ports for the Network Camera on the router� ■ HTTP port ■ RTSP port ■ RTP port for video ■ RTCP port for video If you have changed the port numbe...

VIVOTEK 12 - User's Manual Set up the Network Camera through Power over Ethernet (PoE) When using a PoE-enabled switch The Network Camera is PoE-compliant, allowing transmission of power and data via a single Ethernet cable� Follow the below illustration to connect the Network Camera to a PoE-enable...

VIVOTEK User's Manual - 13 Software Installation Installation Wizard 2 (IW2), free-bundled software included on the product CD, helps you set up your Network Camera on the LAN� 1� Install IW2 under the Software Utility directory from the software CD� Double click the IW2 shortcut on your desktop to ...

VIVOTEK 14 - User's Manual Ready to Use 1� Access the Network Camera on the LAN�2� Retrieve live video through a web browser or recording software� Adjusting the Lens Based on the live image retrieved from the camera, adjust the camera lens by doing the following: To adjust the viewing angle -- 3-ax...

VIVOTEK User's Manual - 15 To adjust the zoom factor and focus range 1� Loosen the zoom controller to adjust the zoom factor� Upon completion, tighten the zoom controller� 2� Loosen the focus controller to adjust the focus range� Upon completion, tighten the focus controller� Completion 1. Rotate th...

VIVOTEK 16 - User's Manual Accessing the Network Camera This chapter explains how to access the Network Camera through web browsers, RTSP players, 3GPP-compatible mobile devices, and VIVOTEK recording software� Using Web Browsers Use Installation Wizard 2 (IW2) to access to the Network Cameras on th...

VIVOTEK User's Manual - 17 ► By default, the Network Camera is not password-protected. To prevent unauthorized access, it is highly recommended to set a password for the Network Camera� For more information about how to enable password protection, please refer to Security on page 30� ► If you see a ...

VIVOTEK 18 - User's Manual Using RTSP Players To view the MPEG-4 streaming media using RTSP players, you can use one of the following players that support RTSP streaming� Quick Time Player Real Player VLC media player mpegable Player pvPlayer As most ISPs and players only allow RTSP streaming throug...

VIVOTEK User's Manual - 19 Using 3GPP-compatible Mobile Devices To view the streaming media through 3GPP-compatible mobile devices, make sure the Network Camera can be accessed over the Internet� For more information on how to set up the Network Camera over the Internet, please refer to Setup the Ne...

VIVOTEK 20 - User's Manual Using VIVOTEK Recording Software The product software CD also contains recording software, allowing simultaneous monitoring and video recording for multiple Network Cameras� Please install the recording software; then launch the program to add the Network Camera to the Cha...

VIVOTEK User's Manual - 21 Main Page This chapter explains the layout of the main page� It is composed of the following sections: VIVOTEK INC� Logo, Host Name, Camera Control Area, Configuration Area, Menu, and Live Video Window� VIVOTEK INC. Logo Click this logo to visit the VIVOTEK website� Host N...

VIVOTEK 22 - User's Manual Configuration Area Client Settings: Click this button to access the client setting page� For more information, please refer to Client Settings on page 25� Configuration: Click this button to access the configuration page of the Network Camera. It is suggested that a passwo...

VIVOTEK 24 - User's Manual Start MP4 Recording: Click this button to record video clips in MP4 file format to your computer� Press the Stop MP4 Recording button to end recording� When you exit the web browser, video recording stops accordingly. To specify the storage destination and file name, pleas...

VIVOTEK User's Manual - 25 Client Settings This chapter explains how to select the stream transmission mode and saving options on the local computer� When completed with the settings on this page, click Save on the page bottom to enable the settings� H.264 / MPEG-4 Protocol Options Depending on your...

VIVOTEK 26 - User's Manual MP4 Saving Options Users can record live video as they are watching it by clicking Start MP4 Recording on the main page. Here, you can specify the storage destination and file name. Folder : Specify a storage destination for the recorded video files. File name prefix: Ente...

VIVOTEK User's Manual - 27 Configuration Click Configuration on the main page to enter the camera setting pages� Note that only Administrators can access the configuration page. VIVOTEK offers an easy-to-use user interface that helps you set up your network camera with minimal effort� To simplify th...

VIVOTEK 28 - User's Manual Advanced Mode Each function on the configuration list will be explained in the following sections. Those functions that are displayed only in Advanced Mode are marked with Advanced Mode � If you want to set up advanced functions, please click [Advanced Mode] on the bottom ...

VIVOTEK User's Manual - 29 System Time Keep current date and time: Select this option to preserve the current date and time of the Network Camera� The Network Camera’s internal real-time clock maintains the date and time even when the power of the system is turned off� Synchronize with computer time...

VIVOTEK 30 - User's Manual Security This section explains how to enable password protection and create multiple accounts� Root Password The administrator account name is “root”, which is permanent and can not be deleted� If you want to add more accounts in the Manage User column, please apply the pa...

VIVOTEK User's Manual - 31 HTTPS (Hypertext Transfer Protocol over SSL) Advanced Mode This section explains how to enable authentication and encrypted communication over SSL (Secure Socket Layer)� It helps protect streaming data transmission over the Internet on higher security level� Enable HTTPS C...

VIVOTEK 32 - User's Manual 4. The Certificate Information will automatically be displayed in the third column as shown below. You can click Property to view detailed information about the certificate. 5� Click Home to return to the main page� Change the address from “ http:// ” to “ https:// “ in th...

VIVOTEK User's Manual - 33 Create self-signed certificate manually 1� Select this option� 2� Click Create to open the Create Certificate page, then click Save to generate the certificate. 3. The Certificate Information will automatically be displayed in the third column as shown below. You can click...

VIVOTEK 34 - User's Manual 3� If you see the following Information bar, click OK and click on the Information bar at the top of the page to allow pop-ups� 4. The pop-up window shows an example of a certificate request.

VIVOTEK User's Manual - 35 5� Look for a trusted certificate authority that issues digital certificates� Enroll the Network Camera� Wait for the certificate authority to issue a SSL certificate; click Browse... to search for the issued certificate, then click Upload in the second column. NOTE ► How ...

VIVOTEK 36 - User's Manual SNMP (Simple Network Management Protocol) Advanced Mode This section explains how to use the SNMP on the network camera� The Simple Network Management Protocol is an application layer protocol that facilitates the exchange of management information between network devices�...

VIVOTEK User's Manual - 37 Network This section explains how to configure a wired network connection for the Network Camera. Network Type LAN Select this option when the Network Camera is deployed on a local area network (LAN) and is intended to be accessed by local computers� The default setting fo...

VIVOTEK User's Manual - 39 NOTE ► If the default ports are already used by other devices connected to the same router, the Network Camera will select other ports for the Network Camera� ► If UPnP TM is not supported by your router, you will see the following message: Error: Router does not support U...

VIVOTEK 40 - User's Manual 4� In the Networking Services dialog box, select Universal Plug and Play and click OK � 5� Click Next in the following window� 6� Click Finish � UPnP TM is enabled� ► How does UPnP TM work? UPnP TM networking technology provides automatic IP configuration and dynamic disco...

VIVOTEK User's Manual - 41 Enable IPv6 Select this option and click Save to enable IPv6 settings� Please note that this only works if your network environment and hardware equipment support IPv6� The browser should be Microsoft ® Internet Explorer 6�5, Mozilla Firefox 3�0 or above� When IPv6 is enab...

VIVOTEK 42 - User's Manual Please follow the steps below to link to an IPv6 address: 1� Open your web browser� 2� Enter the link-global or link-local IPv6 address in the address bar of your web browser� 3� The format should be: 4� Press Enter on the keyboard or click Refresh button to refresh the we...

VIVOTEK User's Manual - 43 IEEE 802�1x Advanced Mode Enable this function if your network environment uses IEEE 802�1x, which is a port-based network access control� The network devices, intermediary switch/access point/hub, and RADIUS server must support and enable 802�1x settings� The 802�1x stand...

VIVOTEK User's Manual - 45 QoS (Quality of Service) Advanced Mode Quality of Service refers to a resource reservation control mechanism, which guarantees a certain quality to different services on the network� Quality of service guarantees are important if the network capacity is insufficient, espec...

VIVOTEK 46 - User's Manual QoS/DSCP (the DiffServ model) DSCP-ECN defines QoS at Layer 3 (Network Layer)� The Differentiated Services (DiffServ) model is based on packet marking and router queuing disciplines. The marking is done by adding a field to the IP header, called the DSCP (Differentiated Se...

VIVOTEK User's Manual - 47 HTTP Advanced Mode To utilize HTTP authentication, make sure that your have set a password for the Network Camera first; please refer to Security on page 30 for details� Authentication: Depending on your network security requirements, the Network Camera provides two types ...

VIVOTEK 48 - User's Manual URL command -- http://<ip address>:<http port>/<access name for stream 1 ~ 5> For example, when the Access name for stream 2 is set to video2�mjpg : 1� Launch Mozilla Firefox or Netscape� 2� Type the above URL command in the address bar� Press Enter � 3. ...

VIVOTEK User's Manual - 49 RTSP Streaming To utilize RTSP streaming authentication, make sure that you have set a password for the Network Camera first; please refer to Security on page 30 for details� Authentication: Depending on your network security requirements, the Network Camera provides three...

VIVOTEK User's Manual - 51 DDNS This section explains how to configure the dynamic domain name service for the Network Camera� DDNS is a service that allows your Network Camera, especially when assigned with a dynamic IP address, to have a fixed host and domain name. DDNS: Dynamic domain name servic...

VIVOTEK 52 - User's Manual 4� Select Enable DDNS and click Save to enable the setting� ■ CustomSafe100 VIVOTEK offers documents to establish a CustomSafe100 DDNS server for distributors and system integrators� You can use CustomSafe100 to register a dynamic domain name if your distributor or system ...

VIVOTEK User's Manual - 53 Access List Advanced Mode This section explains how to control access permission by verifying the client PC’s IP address� General Settings Maximum number of concurrent streaming connection(s) limited to: Simultaneous live viewing for 1~10 clients (including stream 1 ~ stre...

VIVOTEK 54 - User's Manual ■ Refresh: Click this button to refresh all current connections. ■ Add to deny list: You can select entries from the Connection Status list and add them to the Deny List to deny access� Please note that those checked connections will only be disconnected temporarily and wi...

VIVOTEK User's Manual - 55 Network: This rule allows the user to assign a network address and corresponding subnet mask to the Allow/Deny List� For example: Range: This rule allows the user to assign a range of IP addresses to the Allow/Deny List� Note: This rule is only applied to IPv4� For example...

VIVOTEK 56 - User's Manual Video This section explains how to configure the video settings of the Network Camera. Video Settings Video title: Enter a name that will be displayed on the title bar of the live video� Color: Select to display color or black/white video streams� Power line frequency: Set...

VIVOTEK User's Manual - 57 Overlay title and time stamp on video: Select this option to place the video title and time on the video streams� Note that when the frame size is set to 176 x 144 as shown in the picture below, only the time will be stamped on the video streams� Options of Video Advanced ...

VIVOTEK 58 - User's Manual White balance: Adjust the value for the best color temperature� ■ Auto The Network Camera automatically adjusts the color temperature of the light in response to different light sources� The white balance setting defaults to Auto and works well in most situations� ■ Keep c...

VIVOTEK User's Manual - 59 Privacy Mask Advanced Mode Click Privacy Mask to open the settings page� On this page, you can block out sensitive zones to address privacy concerns� ■ To set the privacy mask windows, follow the steps below: 1� Click New to add a new window� 2� Use the mouse to size and d...

VIVOTEK 60 - User's Manual Sensor Settings Advanced Mode Click Sensor Settings to open the Sensor Settings page� On this page, you can set the maximum exposure time, exposure level, and AGC (Auto Gain Control) settings� You can configure two sets of sensor settings: one for normal situations, the ot...

VIVOTEK User's Manual - 61 If you want to configure another sensor setting for day/night/schedule mode, please click Profile to open the Sensor Settings Profile Settings page as shown below. Please follow the steps beolw to setup a profile: 1� Check Enable this profile � 2� Select the applied mode: ...

VIVOTEK 62 - User's Manual Viewing Window Advanced Mode Click Viewing Window to open the Viewing Window Settings page� This Network Camera supports multiple streams with frame size ranging from 176 x 144 to 1600 x 1200� The definition of multiple streams: ■ Stream 1: Users can define the "Region...

VIVOTEK User's Manual - 63 Click Viewing Window to open the viewing region settings page� On this page, you can set the Region of Interest and the Output Frame Size for stream 1 ~ 3� Please follow the steps below to set up those settings for a stream: 1� Select a stream which you want to set up the ...

VIVOTEK 64 - User's Manual Cropping Setting Advanced Mode Click Cropping Setting to open the Cropping Settings page� Please follow the steps below to set up cropping mode for mutiple streams: 1� Click Cropping Setting to open the window as shown below� 2� Select a Captured area from the drop-down li...

VIVOTEK User's Manual - 65 Video Quality Settings Advanced Mode Click the stream item to display the detailed information� The maximum frame size will follow your settings in above sections� This Network Camera offers real-time H.264, MPEG-4 and MJEPG compression standards (Triple Codec) for real-ti...

VIVOTEK 66 - User's Manual ■ Intra frame period Determine how often to plant an I frame� The shorter the duration, the more likely you will get better video quality, but at the cost of higher network bandwidth consumption� Select the intra frame period from the following durations: 1/4 second, 1/2 s...

VIVOTEK 68 - User's Manual Motion Detection This section explains how to configure the Network Camera to enable motion detection. A total of three motion detection windows can be configured. Follow the steps below to enable motion detection:Follow the steps below to enable motion detection: 1� Click...

VIVOTEK User's Manual - 69 A green bar indicates that even though motions have been detected, the event has not been triggered because the image variations still fall under the defined threshold. If you want to configure other motion detection settings for day/night/schedule mode, please click Profi...

VIVOTEK 70 - User's Manual NOTE ► How does motion detection work? There are two motion detection parameters: Sensitivity and Percentage� In the illustration above, frame A and frame B are two sequential images� Pixel differences between the two frames are detected and highlighted in gray (frame C) a...

VIVOTEK User's Manual - 71 Camera Tampering Detection This section explains how to set up camera tamper detection� With tamper detection, the camera is capable of detecting incidents such as redirection , blocking or defocusing , or even spray paint � Please follow the steps below to set up the came...

VIVOTEK 72 - User's Manual Camera Control This section explains how to control the Network Camera’s e-Pan/Tilt/Zoom operation� It allows users to quickly move the focus to a target area for close-up viewing without moving the camera physically� Select Stream: Select one of the stream 1~3 to set up t...

VIVOTEK User's Manual - 73 E-Preset Positions A total of 20 preset positions can be configured. You can select preset positions for the camera to patrol. Please follow the steps below to preset a position: 1� Adjust the shooting area to the desired position using the buttons on the right side of the...

VIVOTEK User's Manual - 75 Home page ■ The e-Preset Positions will also be displayed on the home page� Select one from the drop-down list, and the Network Camera will move to the selected e-preset position� ■ If you have set up different e- preset positions for stream 1~3, you can select one of the ...

VIVOTEK 76 - User's Manual Homepage Layout Advanced Mode This section explains how to set up your own customized homepage layout� Preview This column shows the settings of your hompage layout� You can manually select the background and font colors in Theme Options (the third column on this page)� Th...

VIVOTEK User's Manual - 77 Theme Options Here you can change the color of your homepage layout� There are three types of preset patterns for you to choose from� The new layout will simultaneously appear in the Preview filed. Click Save to enable the settings� Font Color of the Video Title Font Color...

VIVOTEK User's Manual - 79 Application Advanced Mode This section explains how to configure the Network Camera to responds to particular situations (event)� A typical application is that when a motion is detected, the Network Camera sends buffered images to an FTP server or e-mail address as notific...

VIVOTEK 80 - User's Manual Event Settings In the Event Settings column, click Add to open the Event Settings page� On this page, you can arrange three elements -- Trigger, Schedule, and Action to set an event� A total of 3 event settings can be configured. Event name: Enter a name for the event sett...

VIVOTEK User's Manual - 81 An event is an action initiated by a user-defined trigger source; it is the causal arrangement of the following three elements: Trigger, Event Schedule, and Action� Trigger This is the cause or stimulus which defines when to trigger the Network Camera. The trigger source c...

VIVOTEK 82 - User's Manual ■ Camera tampering detection This option allows the Network Camera to trigger when the camera detects that is is being tampered with� To enable this function, you need to configure the Tampering Detection option first. Please refer to page 71 for detailed information� Even...

VIVOTEK User's Manual - 83 To set an event with recorded video or snapshots, it is necessary to configure the server and media settings so that the Network Camera will know what action to take (such as which server to send the media files to) when a trigger is activated� ■ Add Server / Add Media Cli...

VIVOTEK User's Manual - 85 Server Settings Click Add Server on Event Settings page to open the Server Setting page� On this page, you can specify where the notification messages are sent when a trigger is activated. A total of 5 server settings can be configured. Server name: Enter a name for the se...

VIVOTEK User's Manual - 87 HTTP : Select to send the media files to an HTTP server when a trigger is activated. ■ URL: Enter the URL of the HTTP server. ■ User name: Enter the user name if necessary. ■ Password: Enter the password if necessary. To verify if the HTTP settings are correctly configured...

VIVOTEK 88 - User's Manual Media Settings Click Add Media on the Event Settings page to open the Media Settings page� On this page, you can specify the type of media that will be sent when a trigger is activated� A total of 5 media settings can be configured. Media name: Enter a name for the media s...

VIVOTEK 90 - User's Manual You can continue to select a server and media type for the event� Please go back to page 66 for detailed information� ■ SD Test: Click to test your SD card� The system will display a message indicating success or failure� If you want to use your SD card for local storage, ...

VIVOTEK User's Manual - 91 The following is an example of a file destination with video clips: Click 20091120 to open the directory: 20091120 20091121 20091122 Click to delete selected items Click to delete all recorded data The format is: YYYYMMDD Click to open the directory 2009/11/20 2009/11/20 V...

VIVOTEK 92 - User's Manual Recording Advanced Mode This section explains how to configure the recording settings for the Network Camera. Recording Settings NOTE ► Before setting up this page, please set up the Network Storage on the Server Settings page first. ► Please remember to format your SD car...

VIVOTEK User's Manual - 95 Local Storage Advanced Mode This section explains how to manage the local storage on the Network Camera� Here you can view SD card status, search for recorded files to playback, download, etc. SD Card Management SD card status: This column shows the status and reserved spa...

VIVOTEK 96 - User's Manual SD card control ■ Enable cyclic storage: Check this item if you want to enable cyclic recording� When the maximum capacity is reached, the oldest file will be overwritten by the latest one. ■ Enable automatic disk cleanup: Check this item and enter the number of days you w...

VIVOTEK User's Manual - 97 Search Results The following is an example of search results� There are four columns: Trigger time, Media type, Trigger type, and Locked� Click to sort the search results in either direction� View: Click on a search result which will highlight the selected item in purple a...

VIVOTEK 98 - User's Manual Download: Click on a search result to highlight the selected item in purple as shown above� Then click the Download button and a file download window will pop up for you to save the file. JPEGs to AVI: This functions only applies to “JPEG“ format files such as snapshots. Y...

VIVOTEK User's Manual - 99 System Log Advanced Mode This section explains how to configure the Network Camera to send the system log to the remote server as backup� Remote Log You can configure the Network Camera to send the system log file to a remote server as a log backup. Before utilizing this f...

VIVOTEK 100 - User's Manual View Parameters Advanced Mode The View Parameters page lists the entire system’s parameters in alphabetical order� If you need technical assistance, please provide the information listed on this page�

VIVOTEK User's Manual - 101 Maintenance This chapter explains how to restore the Network Camera to factory default, upgrade firmware version, etc� Reboot This feature allows you to reboot the Network Camera, which takes about one minute to complete� When completed, the live video page will be displa...

VIVOTEK 102 - User's Manual Export / Upload Files Advanced Mode This feature allows you to Export / Upload daylight saving time rules, custom language files, and setting backup files. Export daylight saving time configuration file : Click to set the start and end time of DST� Follow the steps below ...

VIVOTEK User's Manual - 103 Upload daylight saving time rule: Click Browse… and specify the XML file to upload. If the incorrect date and time are assigned, you will see the following warning message when uploading the file to the Network Camera. The following message is displayed when attempting to...

VIVOTEK User's Manual - 105 Appendix URL Commands for the Network Camera Overview For some customers who already have their own web site or web control application, the Network Camera/Video Server can be easily integrated through URL syntax� This section specifies the external HTTP-based application...

VIVOTEK 106 - User's Manual General CGI URL Syntax and Parameters CGI parameters are written in lower-case and as one word without any underscores or other separators. When the CGI request includes internal camera parameters, these parameters must be written exactly as they are named in the camera o...

VIVOTEK User's Manual - 107 http://< servername >/cgi-bin/ operator /getparam.cgi?[ <parameter> ] [&<parameter>…] http://< servername >/cgi-bin/ admin /getparam.cgi?[ <parameter> ] [&<parameter>…] Where the <parameter> should be <group> [_ <...

VIVOTEK User's Manual - 109 Example: Set the IP address of server to 192.168.0.123: Request: http://myserver/cgi-bin/admin/setparam.cgi?network_ipaddress=192.168.0.123 Response: HTTP/1.0 200 OK\r\n Content-Type: text/html\r\n Context-Length: 33\r\n \r\n network.ipaddress=192.168.0.123\r\n Available ...

VIVOTEK User's Manual - 141 i<0~19>_size <window size> 1/7 Width and height of the preset. (It should be set by eCamCtrl.cgi rather than by setparam.cgi.) Drive the Digital Output Note: This request requires Viewer privileges. Method: GET/POST Syntax: http://< servername >/cgi-bin/...

VIVOTEK 142 - User's Manual Content-Type: text/plain\r\n Content-Length: <length> \r\n \r\n [di0=<state>]\r\n [di1=<state>]\r\n [di2=<state>]\r\n [di3=<state>]\r\n where <state> can be 0 or 1. Example: Query the status of digital input 1. Query Status of the Digit...

VIVOTEK User's Manual - 143 [do3=<state>]\r\n where <state> can be 0 or 1. Example: Query the status of digital output 1. Request: http://myserver/cgi-bin/dido/getdo.cgi?do1 Response: HTTP/1.0 200 OK\r\n Content-Type: text/plain\r\n Content-Length: 7\r\n \r\n do1=1\r\n Capture Single Sna...

VIVOTEK 144 - User's Manual <binary JPEG image data> Account Management Note: This request requires Administrator privileges. Method: GET/POST Syntax: http://< servername >/cgi-bin/admin/editaccount.cgi ? method=<value>&username= <name> [&userpass= <value> ][&am...

VIVOTEK User's Manual - 145 Syntax: http://< servername >/cgi-bin/admin/syslog.cgi Server will return the most up-to-date system log. Return: HTTP/1.0 200 OK\r\n Content-Type: text/plain\r\n Content-Length: <syslog length>\r\n \r\n <system log information>\r\n Upgrade Firmware Note...

VIVOTEK 146 - User's Manual [&speedpan=<value>][&speedtilt=<value>][&speedzoom=<value>][&speedapp= < value > ] [&return=<return page>] PARAMETER VALUE DESCRIPTION channel <0~(n-1)> Channel of video source. stream <0~(m-1)> Stream. home Mo...

VIVOTEK User's Manual - 147 PARAMETER VALUE DESCRIPTION channel <0~(n-1)> Channel of the video source. stream <0~(m-1)> Stream. recall Text string less than 40 characters One of the present positions to recall. return <return page> Redirect to the page <return page> after the...

VIVOTEK 148 - User's Manual Return: HTTP/1.0 200 OK\r\n Content-Type: text/plain\r\n Content-Length: <system information length>\r\n \r\n Model=<model name of server>\r\n CapVersion=0200\r\n PARAMETER (supported capability version) VALUE DESCRIPTION Model system.firmwareversion Model nam...

VIVOTEK User's Manual - 149 ip <ip address> Single address: <ip address> Network address: <ip address / network mask> Range address:<start ip address - end ip address> index <value> The start position to add or to delete. return <return page> Redirect to the page ...

VIVOTEK 154 - User's Manual Technical Specifications Technical Specifications On-board Storage ． SD/SDHC card slot ． Stores snapshots and video clips Security ． Multi-level user access with password protection ． IP address filtering ． HTTPS encrypted data transmission ． 802.1X port-based authenticat...

VIVOTEK User's Manual - 155 Technology License Notice MPEG-4 AAC Technology THIS PRODUCT IS LICENSED UNDER THE MPEG-4 AAC AUDIO PATENT LICENSE� THIS PRODUCT MAY NOT BE DECOMPILED, REVERSE-ENGINEERED OR COPIED, EXCEPT WITH REGARD TO PC SOFTWARE, OF WHICH YOU MAY MAKE SINGLE COPIES FOR ARCHIVAL PURPOS...

VIVOTEK 156 - User's Manual Electromagnetic Compatibility (EMC) FCC Statement This device compiles with FCC Rules Part 15� Operation is subject to the following two conditions� ■ This device may not cause harmful interference, and■ This device must accept any interference received, including interfe...