Vivotek FD8335H - Manuals

VIVOTEK 6 - User's Manual Physical Description Inner View General I/O Terminal Block This Network Camera provides a general I/O terminal block which is used to connect external input / output devices. The pin definitions are described below. The 24V AC can be used as an alternate power source� 8 7 6...

VIVOTEK 8 - User's Manual Hardware Reset The reset button is used to reset the system or restore the factory default settings� Sometimes resetting the system can return the camera to normal operation� If the system problems remain after reset, restore the factory settings and install again� Reset : ...

VIVOTEK User's Manual - 9 IMPORTANT! Connect power lines and if you have external devices such as sensors and alarms, make the connection from the general I/O terminal block� Cabling Assembly Power and IO cables pass through a waterproof connector� The Ethernet cable should be routed through a rubbe...

VIVOTEK 10 - User's Manual 1� D i s a s s e m b l e t h e c o m p o n e n t s o f t h e waterproof connector into parts (A) ~ (F) as shown above� 2� Place the screw nut (E) on the Power and GPIO opening� 3� F e e d t h e p o w e r c a b l e s t h r o u g h t h e waterproof connector (F --> E --&g...

VIVOTEK 12 - User's Manual Record the MAC address under the camera base before installing the camera� Replace the side opening cover with the included side outlet bushing if you want to route cables from the side of camera� The 1/2" protection conduits and tubing, if applied, are separately purc...

VIVOTEK User's Manual - 13 1 2 3 A 4 B 5 Wall mount 1� Attach the supplied alignment sticker to the wall� 2� Using the circle marks on the sticker, drill at least 2 pilot holes symmetrically on each side into the wall� Then hammer the four supplied plastic anchors into the holes� 3� Through three or...

VIVOTEK 14 - User's Manual Ceiling mount 1� Attach the supplied alignment sticker to the ceiling� 2� Using the circle marks on the sticker, drill at least 2 pilot holes symmetrically on each side into the ceiling� Then hammer the four supplied plastic anchors into the holes� 3� Through three or four...

VIVOTEK User's Manual - 15 Network Deployment General Connection (without PoE) POWER COLLISION LINK RECEIVE PARTITION 1 2 3 4 5 1� Connect RJ45 Ethernet cable to a switch� Use a Category 5 Cross Cable when your network camera is directly connected to PC� 2� Connect the AC cables from the terminal bl...

VIVOTEK 16 - User's Manual POWER COLLISION LINK RECEIVE PARTITION 1 2 3 4 5 When using a non-PoE switch Use a PoE power injector (optional) to connect between the Network Camera and a non-PoE switch� PoE Power Injector (optional) Non-PoE Switch

VIVOTEK User's Manual - 17 Internet connection via a router Before setting up the Network Camera over the Internet, make sure you have a router and follow the steps below� 1� Connect your Network Camera behind a router, the Internet environment is illustrated below� Regarding how to obtain your IP a...

VIVOTEK 18 - User's Manual Software Installation Installation Wizard 2 (IW2), free-bundled software included on the product CD, helps you set up your Network Camera on the LAN� 1� Install IW2 under the Software Utility directory from the software CD� Double-click the IW2 shortcut on your desktop to ...

VIVOTEK User's Manual - 19 Ready to Use 1� A browser session with the Network Camera should prompt as shown below� 2� You should be able to see live video from your camera� You may also install the 32-channel recording software from the software CD in a deployment consisting of multiple cameras� For...

VIVOTEK 20 - User's Manual W T 8 N To adjust the zoom factor and focus range 1� Loosen the zoom controller and then adjust zoom factor by moving the controller left and right� Upon completion, tighten the zoom controller screw� 2� Loosen the focus controller and then adjust focus range by moving the...

VIVOTEK User's Manual - 21 Accessing the Network Camera This chapter explains how to access the Network Camera through web browsers, RTSP players, 3GPP-compatible mobile devices, and VIVOTEK recording software� Using Web Browsers Use Installation Wizard 2 (IW2) to access the Network Cameras on LAN� ...

VIVOTEK 22 - User's Manual ► By default, the Network Camera is not password-protected. To prevent unauthorized access, it is highly recommended to set a password for the Network Camera� For more information about how to enable password protection, please refer to Security on page 75� ► If you see a ...

VIVOTEK User's Manual - 23 IMPORTANT! • Currently the Network Camera utilizes 32-bit ActiveX plugin. You CAN NOT open a management/view session with the camera using a 64-bit IE browser� • If you encounter this problem, try execute the Iexplore.exe program from C:\ Windows\SysWOW64. A 32-bit version...

VIVOTEK 24 - User's Manual Using RTSP Players To view the MPEG-4 streaming media using RTSP players, you can use one of the following players that support RTSP streaming� Quick Time Player Real Player VLC media player mpegable Player pvPlayer As most ISPs and players only allow RTSP streaming throug...

VIVOTEK User's Manual - 25 Using 3GPP-compatible Mobile Devices To view the streaming media through 3GPP-compatible mobile devices, make sure the Network Camera can be accessed over the Internet� For more information on how to set up the Network Camera over the Internet, please refer to Setup the Ne...

VIVOTEK 26 - User's Manual Using VIVOTEK Recording Software The product software CD also contains an ST-7501 recording software, allowing simultaneous monitoring and video recording for multiple Network Cameras� Please install the recording software; then launch the program to add the Network Camera...

VIVOTEK User's Manual - 27 Main Page This chapter explains the layout of the main page. It is composed of the following sections: VIVOTEK INC� Logo, Host Name, Camera Control Area, Configuration Area, Menu, and Live Video Window� VIVOTEK INC. Logo Click this logo to visit the VIVOTEK website� Host N...

VIVOTEK 28 - User's Manual Focus Assist_ There are two options for you to fine-tune the camera focus. You can either connect the camera to an analog display device, camera tester, or adjust the focus through networking� Please follow the steps below: ■ Phone-jack AV Out (to BNC) 1� Connect a camera ...

VIVOTEK User's Manual - 29 Configuration Area Client Settings : Click this button to access the client setting page. For more information, please refer to Client Settings on page 32� Configuration: Click this button to access the configuration page of the Network Camera. It is suggested that a passw...

VIVOTEK 30 - User's Manual Video and Audio Control Buttons : Depending on the Network Camera model and Network Camera configuration, some buttons may not be available. Snapshot : Click this button to capture and save still images. The captured images will be displayed in a pop-up window� Right-click...

VIVOTEK 32 - User's Manual Client Settings This chapter explains how to select the stream transmission mode and saving options on the local computer� When completed with the settings on this page, click Save on the page bottom to enable the settings� H.264 / MPEG-4 Media Options Select to stream vid...

VIVOTEK User's Manual - 33 MP4 Saving Options Users can record live video as they are watching it by clicking Start MP4 Recording on the main page. Here, you can specify the storage destination and file name. Folder : Specify a storage destination for the recorded video files. File name prefix: Ente...

VIVOTEK 34 - User's Manual Configuration Click Configuration on the main page to enter the camera setting pages� Note that only Administrators can access the configuration page. VIVOTEK offers an easy-to-use user interface that helps you set up your network camera with minimal effort. To simplify th...

VIVOTEK User's Manual - 35 Advanced Mode Each function on the configuration list will be explained in the following sections. Those functions that are displayed only in Advanced Mode are marked with Advanced Mode � If you want to set up advanced functions, please click [Advanced Mode] on the bottom ...

VIVOTEK 36 - User's Manual System time Keep current date and time : Select this option to preserve the current date and time of the Network Camera� The Network Camera’s internal real-time clock maintains the date and time even when the power of the system is turned off� Synchronize with computer tim...

VIVOTEK User's Manual - 37 System > Homepage layout Advanced Mode This section explains how to set up your own customized homepage layout� General settings This column shows the settings of your hompage layout� You can manually select the background and font colors in Theme Options (the second ta...

VIVOTEK 38 - User's Manual Theme Options Here you can change the color of your homepage layout� There are three types of preset patterns for you to choose from� The new layout will simultaneously appear in the Preview filed. Click Save to enable the settings� Font Color of the Video Title Background...

VIVOTEK User's Manual - 39 ■ Follow the steps below to set up the customed homepage: 1� Click Custom on the left column� 2. Click the field where you want to change the color on the right column. 3� The palette window will pop up as shown below� 4� Drag the slider bar and click on the left square to...

VIVOTEK 40 - User's Manual System > Logs Advanced Mode This section explains how to configure the Network Camera to send the system log to a remote server as backup� Log server settings Follow the steps below to set up the remote log: 1� Select Enable remote log � 2� In the IP address text box, e...

VIVOTEK User's Manual - 41 Access log Access log displays the access time and IP address of all viewers (including operators and administrators) in a chronological order� The access log is stored in the Network Camera’s buffer area and will be overwritten when reaching a certain limit� System > P...

VIVOTEK 42 - User's Manual System > Maintenance This chapter explains how to restore the Network Camera to factory default, upgrade firmware version, etc� General settings > Upgrade firmware This feature allows you to upgrade the firmware of your Network Camera� It takes a few minutes to compl...

VIVOTEK User's Manual - 43 General settings > Restore This feature allows you to restore the Network Camera to factory default settings� Network : Select this option to retain the Network Type settings (please refer to Network Type on page 57)� Daylight Saving Time : Select this option to retain ...

VIVOTEK 44 - User's Manual 3. Open the file with Microsoft ® Notepad and locate your time zone; set the start and end time of DST� When completed, save the file. In the example below, DST begins each year at 2:00 a.m. on the second Sunday in March and ends at 2:00 a.m. on the first Sunday in Novembe...

VIVOTEK User's Manual - 45 The following message is displayed when attempting to upload an incorrect file format. Export language file : Click to export language strings. VIVOTEK provides nine languages: English, Deutsch, Español, Français, Italiano, 日本語, Português, 簡体中文 , and 繁體中文 � Update custom l...

VIVOTEK 46 - User's Manual Security > User Account This section explains how to enable password protection and create multiple accounts� Root Password The administrator account name is “root”, which is permanent and can not be deleted� If you want to add more accounts in the Manage User column, p...

VIVOTEK User's Manual - 47 Security > HTTPS (Hypertext Transfer Protocol over SSL) This section explains how to enable authentication and encrypted communication over SSL (Secure Socket Layer)� It helps protect streaming data transmission over the Internet on higher security level� Create and Ins...

VIVOTEK User's Manual - 49 Create certificate and install : Select this option if you want to create a certificate from a certification authority. 1� Select this option from a method pull-down menu� 2� Click Create certificate to generate the certificate. 3� The following information will appear in ...

VIVOTEK 50 - User's Manual 4. The Certificate Information will automatically be displayed in the third column as shown below. You can click Property to see detailed information about the certificate. 5 . Copy the contents of the Certificate request (in PEM format). Use the contents to apply for a 3r...

VIVOTEK User's Manual - 51 NOTE ► How do I cancel the HTTPS settings? 1� Click on the Remove certificate button� 2� If you are currently running a secure connection The webpage will redirect to a non-HTTPS page automatically� Enable HTTPS Check this item to enable HTTPS communication, then select a ...

VIVOTEK 52 - User's Manual Security > Access List Advanced Mode This section explains how to control access permission by verifying the client PC’s IP address� General Settings Maximum number of concurrent streaming connection(s) limited to : Simultaneous live viewing for 1~10 clients (including ...

VIVOTEK User's Manual - 53 ■ Refresh: Click this button to refresh all current connections. ■ Add to deny list: You can select entries from the Connection Status list and add them to the Deny List to deny access� Please note that those checked connections will only be disconnected temporarily and wi...

VIVOTEK 54 - User's Manual Network : This rule allows the user to assign a network address and corresponding subnet mask to the Allow/Deny List� The address and network mask are written in CIDR format� For example: Range : This rule allows the user to assign a range of IP addresses to the Allow/Deny...

VIVOTEK User's Manual - 55 Security > IEEE 802.1X Advanced Mode Enable this function if your network environment uses IEEE 802�1x, which is a port-based network access control� The network devices, intermediary switch/access point/hub, and RADIUS server must support and enable 802�1x settings� Th...

VIVOTEK 56 - User's Manual 3� When all settings are complete, move the Network Camera to the protected LAN by connecting it to an 802�1x enabled switch� The devices will then start the authentication automatically� ► The authentication process for 802.1x: 1� The Certificate Authority (CA) provides t...

VIVOTEK User's Manual - 57 Network > General settings This section explains how to configure a wired network connection for the Network Camera. Network Type LAN Select this option when the Network Camera is deployed on a local area network (LAN) and is intended to be accessed by local computers� ...

VIVOTEK 58 - User's Manual Primary DNS : The primary domain name server that translates hostnames into IP addresses. Secondary DNS : Secondary domain name server that backups the Primary DNS. Primary WINS server : The primary WINS server that maintains the database of computer names and IP addresses...

VIVOTEK User's Manual - 59 NOTE ► If the default ports are already used by other devices connected to the same router, the Network Camera will select other ports for the Network Camera� ► If UPnP TM is not supported by your router, you will see the following message: Error: Router does not support U...

VIVOTEK 60 - User's Manual 4� In the Networking Services dialog box, select Universal Plug and Play and click OK � 5� Click Next in the following window� 6� Click Finish � UPnP TM is enabled� ► How does UPnP TM work? UPnP TM networking technology provides automatic IP configuration and dynamic disco...

VIVOTEK User's Manual - 61 Enable IPv6 Select this option and click Save to enable IPv6 settings� Please note that this only works if your network environment and hardware equipment support IPv6� The browser should be Microsoft ® Internet Explorer 6�5, Mozilla Firefox 3�0 or above� When IPv6 is enab...

VIVOTEK 62 - User's Manual Please follow the steps below to link to an IPv6 address: 1� Open your web browser� 2� Enter the link-global or link-local IPv6 address in the address bar of your web browser� 3. The format should be: 4� Press Enter on the keyboard or click Refresh button to refresh the we...

VIVOTEK User's Manual - 63 Port HTTPS port : By default, the HTTPS port is set to 443. It can also be assigned to another port number between 1025 and 65535� Two way audio port : By default, the two way audio port is set to 5060. Also, it can also be assigned to another port number between 1025 and ...

VIVOTEK 64 - User's Manual 2011/06/09 17:08:56 Audio is being transmitted to the Network Camera Mute Mic Volume Talk Button Click to enable audio transmission to the Network Camera; click to adjust the volume of microphone; click to turn off the audio� To stop talking, click again� FTP port : The FT...

VIVOTEK User's Manual - 65 Network > Streaming protocols Advanced Mode HTTP streaming To utilize HTTP authentication, make sure that your have set a password for the Network Camera first; please refer to Security > User account on page 75 for details� Authentication : Depending on your network...

VIVOTEK 66 - User's Manual URL command -- http://<ip address>:<http port>/<access name for stream 1 or 2> For example, when the Access name for stream 2 is set to video2�mjpg : 1� Launch Mozilla Firefox or Netscape� 2� Type the above URL command in the address bar� Press Enter � 3�...

VIVOTEK User's Manual - 67 Authentication : Depending on your network security requirements, the Network Camera provides three types of security settings for streaming via RTSP protocol: disable, basic, and digest. If basic authentication is selected, the password is sent in plain text format, but t...

VIVOTEK 68 - User's Manual Multicast settings for stream 1 & 2: Click the items to display the detailed configuration information. Select the Always multicast option to enable multicast for stream 1 or 2� Unicast video transmission delivers a stream through point-to-point transmission; multicast...

VIVOTEK User's Manual - 69 Network > DDNS This section explains how to configure the dynamic domain name service for the Network Camera� DDNS is a service that allows your Network Camera, especially when assigned with a dynamic IP address, to have a fixed host and domain name. Express link Expres...

VIVOTEK 70 - User's Manual Manual setup DDNS: Dynamic domain name service Enable DDNS : Select this option to enable the DDNS setting. Provider : Select a DDNS provider from the provider drop-down list. VIVOTEK offers Safe100.net , a free dynamic domain name service, to VIVOTEK customers� It is reco...

VIVOTEK User's Manual - 71 [Register] Successfully Your account information has been mailed to registered e-mail address 4� Select Enable DDNS and click Save to enable the setting� ■ CustomSafe100 VIVOTEK offers documents to establish a CustomSafe100 DDNS server for distributors and system integrato...

VIVOTEK 72 - User's Manual Network > QoS (Quality of Service) Advanced Mode Quality of Service refers to a resource reservation control mechanism, which guarantees a certain quality to different services on the network� Quality of service guarantees are important if the network capacity is insuff...

VIVOTEK User's Manual - 73 QoS/DSCP (the DiffServ model) DSCP-ECN defines QoS at Layer 3 (Network Layer)� The Differentiated Services (DiffServ) model is based on packet marking and router queuing disciplines. The marking is done by adding a field to the IP header, called the DSCP (Differentiated Se...

VIVOTEK 74 - User's Manual Network > SNMP (Simple Network Management Protocol) This section explains how to use the SNMP on the network camera� The Simple Network Management Protocol is an application layer protocol that facilitates the exchange of management information between network devices� ...

VIVOTEK User's Manual - 75 Media > Image Advanced Mode This section explains how to configure the image settings of the Network Camera� It is composed of the following four columns: General settings, Picture settings, Exposure, and Privacy mask� General settings Show information in videos and sna...

VIVOTEK 76 - User's Manual Day/Night Settings Switch to B/W in night mode Select this to enable the Network Camera to automatically switch to Black/White during night mode� Turn on external IR illuminator in night mode Select this to turn on an external IR illuminator (connected via Digital Output l...

VIVOTEK User's Manual - 77 Preference On this page, you can tune the White balance, Image adjustment and WDR enhanced � White balance : Adjust the value for the best color temperature. ■ You may follow the steps below to adjust the white balance to the best color temperature. 1� Place a sheet of pap...

VIVOTEK 78 - User's Manual WDR : This function allows users to identify more details of objects in the high contrast environment especially for details in the shaded area� You may check Enable WDR checkbox, and then adjust the sensitivity (low, high) and the strength (low, medium, high) to reach the...

VIVOTEK User's Manual - 79 Measurement Window : This function allows user to set measurement window(s) for low light compesation� ■ Full view: Calculate the full range of view and offer appropriate light compesation� ■ Custom: This option allows you to manually add a specific window as a measuring a...

VIVOTEK 80 - User's Manual You can click Restore to recall the original settings without incorporating the changes� When completed with the settings on this page, click Save to enable the settings� If you want to configure another sensor setting for day/night/schedule mode, please click Profile to o...

VIVOTEK User's Manual - 81 Privacy mask Advanced Mode Click Privacy Mask to open the settings page� On this page, you can block out sensitive zones to address privacy concerns� ■ To set the privacy mask windows, follow the steps below: 1� Click New to add a new window� 2� You can use the mouse curso...

VIVOTEK 82 - User's Manual Media > Video Stream settings This Network Camera supports multiple streams with frame size ranging from 300 x 200 to 1280 x 800� The definition of multiple streams: ■ Stream 1: Users can define the "Region of Interest" (viewing region) and the "Output Frame...

VIVOTEK User's Manual - 83 Media > Video ► All the items in the “Region of Interest” should not be larger than the “Output Frame Size“ (current maximum resolution)� ■ The parameters of the multiple streams: When completed with the settings in the Viewing Window, click Save to enable the settings ...

VIVOTEK 84 - User's Manual Click the stream item to display the detailed information� The maximum frame size will follow your settings in the above Viewing Window sections� This Network Camera offers real-time H�264, MPEG-4 (Stream #2) and MJPEG compression standards (Triple Codec) for real-time vie...

VIVOTEK User's Manual - 85 The frame rate will decrease if you select a higher resolution� ■ Intra frame period Determine how often to plant an I frame� The shorter the duration, the more likely you will get better video quality, but at the cost of higher network bandwidth consumption� Select the in...

VIVOTEK 86 - User's Manual If JPEG mode is selected, the Network Camera sends consecutive JPEG images to the client, producing a moving effect similar to a filmstrip� Every single JPEG image transmitted guarantees the same image quality, which in turn comes at the expense of variable bandwidth usage...

VIVOTEK User's Manual - 87 Media > Audio Audio Settings Mute : Select this option to disable audio transmission from the Network Camera to all clients. Note that if muted, no audio data will be transmitted even if audio transmission is enabled on the Client Settings page. In that case, the follow...

VIVOTEK 88 - User's Manual PTZ > PTZ settings This section explains how to control the Network Camera’s Pan/Tilt/Zoom operation� There are two ways to enable the function:1. Digital: Control the e-PTZ operation. It allows users to quickly move the focus to a target area for close-up viewing witho...

VIVOTEK User's Manual - 89 Auto pan/patrol speed : Select the speed from 1~5 (slow/fast) to set up the Auto pan/patrol speed control� When completed with the e-PTZ settings, click Save to enable the settings on this page� Home page in E-PTZ Mode ■ The e-Preset Positions will also be displayed on the...

VIVOTEK 90 - User's Manual Patrol settings You can select some preset positions for the Network Camera to patrol� Please follow the steps below to set up a patrol schedule: 1� Select the preset locations on the list, and click � 2� The selected preset locations will be displayed on the Patrol locati...

VIVOTEK User's Manual - 91 NOTE ► The Preset Positions will also be displayed on the home page. Select one from the Go to drop-down list, and the Network Camera will move to the selected preset position. ► Click Patrol: The Network Camera will patrol along the selected positions repeatedly. Please r...

VIVOTEK 92 - User's Manual Event > Event settings This section explains how to configure the Network Camera to responds to particular situations (event)� A typical application is that when a motion is detected, the Network Camera sends buffered images to an FTP server or e-mail address as notific...

VIVOTEK User's Manual - 93 ■ Event name: Enter a name for the event setting. ■ Enable this event: Select this option to enable the event setting. ■ Priority: Select the relative importance of this event (High, Normal, or Low). Events with a higher priority setting will be executed first. ■ Detect ne...

VIVOTEK 94 - User's Manual ■ Camera tampering detection This option allows the Network Camera to trigger when the camera detects that is is being tampered with� To enable this function, you need to configure the Tampering Detection option first. Please refer to page 108 for detailed information� ■ M...

VIVOTEK User's Manual - 95 Add server To set an event with recorded video or snapshots, it is necessary to configure the server and media settings so that the Network Camera will know what action to take (such as which server to send the media files to) when a trigger is activated. Click Add server ...

VIVOTEK 96 - User's Manual To verify if the email settings are correctly configured, click Test � The result will be shown in a pop-up window� If successful, you will also receive an email indicating the result� Click Save server to enable the settings� Note that after you set up the first event ser...

VIVOTEK 98 - User's Manual Network storage : Select to send the media files to a network storage location when a trigger is activated� Please refer to NAS server on page 112 for details� Click Save server to enable the settings� ■ SD Test: Click to test your SD card. The system will display a messag...

VIVOTEK 100 - User's Manual Add media Click Add media to open the media setting window� You can specify the type of media that will be sent when a trigger is activated. A total of 5 media settings can be configured. There are three choices of media types available: Snapshot, Video Clip, and System l...

VIVOTEK User's Manual - 101 ■ Add date and time suffix to the file name Select this option to add a date/time suffix to the file name. For example: Click Save media to enable the settings� To note that after you set up the first media server, a new column for media server will automatically show up ...

VIVOTEK 102 - User's Manual ■ Maximum file size Specify the maximum file size allowed. ■ File name prefix Enter the text that will be appended to the front of the file name. For example: Click Save media to enable the settings� Media type - System log Select to send a system log when a trigger is ac...

VIVOTEK User's Manual - 103 In the Event settings column, the Servers and Medias you configured will be listed; please make sure the Event -> Status is indicated as ON , in order to enable the event triggering action� When completed, click Save event to enable the settings and click Close to exit...

VIVOTEK 104 - User's Manual Customized Script This function allows you to upload a sample script (.xml file) to the webpage, which will save your time on configuring the settings. Please note that there is a limited number of customized scripts you can upload; if the current amount of customized scr...

VIVOTEK User's Manual - 105 Applications > Motion detection This section explains how to configure the Network Camera to enable motion detection. A total of three motion detection windows can be configured. Follow the steps below to enable motion detection:Follow the steps below to enable motion ...

VIVOTEK 106 - User's Manual A green bar indicates that even though motions have been detected, the event has not been triggered because the image variations still fall under the defined threshold. If you want to configure other motion detection settings for day/night/schedule mode, please click Prof...

VIVOTEK User's Manual - 107 NOTE ► How does motion detection work? There are two motion detection parameters: Sensitivity and Percentage. In the illustration above, frame A and frame B are two sequential images� Pixel differences between the two frames are detected and highlighted in gray (frame C) ...

VIVOTEK 108 - User's Manual Applications > DI and DO Connect DI or DO devices to the camera's terminal block, the camera will automatically detect the current connection state as pulled-high or pulled-low� You may then define the triggering condition� Digital input : Select High or Low to define ...

VIVOTEK User's Manual - 109 Recording > Recording settings Advanced Mode This section explains how to configure the recording settings for the Network Camera. Recording Settings NOTE ► Please remember to format your SD card when using it for the first time. Please refer to page 114 for detailed i...

VIVOTEK User's Manual - 111 2� Destination You can select the SD card or network storage (NAS) for the recorded video files. NAS server Click Add NAS server to open the server setting window and follow the steps below to set up: 1� Fill in the information for your server� For example: 2� Click Test ...

VIVOTEK User's Manual - 113 To remove a recording setting from the list, select a recording name from the drop-down list and click Delete � ■ Click Video (Name) : Opens the Recording Settings page to modify. ■ Click ON (Status) : The Status will become OFF and stop recording� ■ Click NAS (Destinatio...

VIVOTEK 114 - User's Manual Local storage > SD card management This section explains how to manage the local storage on the Network Camera� Here you can view SD card status, and implement SD card control� SD card staus This column shows the status and reserved space of your SD card� Please rememb...

VIVOTEK User's Manual - 115 Local storage > Content management This section explains how to manage the content of recorded videos on the Network Camera� Here you can search and view the records and view the searched results� Searching and Viewing the Records This column allows the user to set up ...

VIVOTEK 116 - User's Manual Search Results The following is an example of search results. There are four columns: Trigger time, Media type, Trigger type, and Locked� Click to sort the search results in either direction� Numbers of entries displayed on one page Enter a key word to filter the search r...

VIVOTEK 118 - User's Manual Appendix URL Commands for the Network Camera 1. Overview For some customers who already have their own web site or web control application, the Network Camera/Video Server can be easily integrated through URL syntax� This section specifies the external HTTP-based applicat...

VIVOTEK User's Manual - 119 3. General CGI URL Syntax and Parameters CGI parameters are written in lower-case and as one word without any underscores or other separators. When the CGI request includes internal camera parameters, these parameters must be written exactly as they are named in the camer...

VIVOTEK 120 - User's Manual [&<parameter>…] http://< servername >/cgi-bin/ operator /getparam.cgi?[ <parameter> ] [&<parameter>…] http://< servername >/cgi-bin/ admin /getparam.cgi?[ <parameter> ] [&<parameter>…] Where the <parameter> shoul...

VIVOTEK User's Manual - 121 6. Set Server Parameter Values Note: The access right depends on the URL directory. Method: GET/POST Syntax: http://< servername >/cgi-bin/ anonymous /setparam.cgi? <parameter>=<value> [&<parameter>=<value>…][&update=<value>][&a...

VIVOTEK 122 - User's Manual <parameter>=<value>\r\n [<parameter pair>] Only the parameters that you set and are readable will be returned. Example: Set the IP address of server to 192.168.0.123: Request: http://myserver/cgi-bin/admin/setparam.cgi?network_ipaddress=192.168.0.123 Res...

VIVOTEK User's Manual - 129 7.2 status Group: status NAME VALUE DEFAULT SECURITY (get/set) DESCRIPTION di_i<0~(ndi-1)> <boolean> 0 1/7 0 => Inactive, normal 1 => Active, triggered (capability.ndi > 0) do_i<0~(ndo-1)> <boolean> 0 1/7 0 => Inactive, normal 1 => A...

VIVOTEK 130 - User's Manual 7.4 digital output behavior define Group: do_i<0~(ndo-1)> (capability.ndo > 0) NAME VALUE DEFAULT SECURITY (get/set) DESCRIPTION normalstate open, grounded open 1/1 Indicate open circuit or closed circuit (inactive status) 7.5 security Group: security NAME VALUE ...

VIVOTEK 142 - User's Manual 0 : 2x 1 : 4x 2 : 8x 3 : 16x 4 : 32x 5 : 64x whitebalance auto, manual auto 4/4 “auto” indicates auto white balance. “manual” indicates keep current value. piris_response 1~3 1 4/4 P-Iris response time piris_position 0~50 0 1/4 P-Iris position. 0 : P-Iris open to largest ...

VIVOTEK 144 - User's Manual 7.11 Image setting per channel Group: image_c<0~(n-1)> for n channel products NAME VALUE DEFAULT SECURITY (get/set) DESCRIPTION brightness -5~5 -5 4/4 Adjust brightness of image according to mode settings. saturation -5~5 0 4/4 Adjust saturation of image according t...

VIVOTEK User's Manual - 145 image according to mode settings. profile_i0_gammacurve 0,45,50,60,70,80,90,100 0 4/4 Gamma curve profile_i0_lowlightmode <boolean> 0 4/4 Enable/disable low light mode. 7.12 Image setting for preview Group: imagepreview_c<0~(n-1)> for n channel products NAME V...

VIVOTEK 146 - User's Manual 7.13 Exposure window setting per channel Group: exposure_c<0~(n-1)> for n channel products NAME VALUE DEFAULT SECURITY (get/set) DESCRIPTION mode auto, custom auto 4/4 The mode indicates how to decide the exposure. auto: Use full view as the only one exposure window...

VIVOTEK User's Manual - 147 7.14 Audio input per channel Group: audioin_c<0~(n-1)> for n channel products (capability.audioin>0) NAME VALUE DEFAULT SECURITY (get/set) DESCRIPTION mute 0, 1 1 4/4 Enable audio mute. gain 1,5,9,13,17,21,25, 29,33,37,41,45,49,53,57,61 17 4/4 Gain of input. (aud...

VIVOTEK User's Manual - 149 i<0~(m-1)>_win_i<0~2>_objsize 0 ~ 100 0 4/4 Percent of motiondetection window. i<0~(m-1)>_win_i<0~2>_sensitivity 0 ~ 100 0 4/4 Sensitivity of motiondetection window. 7.16 Tempering detection settings Group: tampering_c<0~(n-1)> for n channel ...

VIVOTEK 150 - User's Manual ernameemail the DDNS service provider <provider>_passwordkey string[64] <blank> 6/6 Your password or key to login to the DDNS service provider. <provider>_servername string[128] <blank> 6/6 The server name for safe100. (This field only exists if th...

VIVOTEK 152 - User's Manual secnamerw string[31] Private 6/6 Read/write security name secnamero string[31] Public 6/6 Read only security name authpwrw string[8~128] <blank> 6/6 Read/write authentication password authpwro string[8~128] <blank> 6/6 Read only authentication password authtyp...

VIVOTEK 160 - User's Manual 7.26 Customized event script Group: event_customtaskfile_i<0~2> PARAMETER VALUE Default SECURITY (get/set) DESCRIPTION name string[41] <blank> 6/7 Custom script identification of this entry. date string[17] <blank> 6/7 Date of custom script. time string[...

VIVOTEK User's Manual - 163 7.28 Server setting for event action Group: server_i <0~4> PARAMETER VALUE DEFAULT SECURITY (get/set) DESCRIPTION Name string[40] NULL 6/6 Identification of this entry Type email, ftp, http, ns email 6/6 Indicate the server type: “email” = email server “ftp” = FTP s...

VIVOTEK 164 - User's Manual 7.29 Media setting for event action Group: media_i<0~4> (media_freespace is used internally.) PARAMETER VALUE DEFAULT SECURITY (get/set) DESCRIPTION name string[40] NULL 6/6 Identification of this entry type snapshot, systemlog, videoclip, recordmsg snapshot 6/6 Med...

VIVOTEK 168 - User's Manual information. stateorprovincename string[128] Asia 6/6 State or province name in the certificate information. localityname string[128] Asia 6/6 The locality name in the certificate information. organizationname string[64] Vivotek.Inc 6/6 Organization name in the certificat...

VIVOTEK User's Manual - 171 8. Useful Functions 8.1 Drive the Digital Output (capability.ndo > 0) Note: This request requires Viewer privileges. Method: GET/POST Syntax: http://< servername >/cgi-bin/dido/setdo.cgi?do1= <state> [&do2=<state>] [&do3=<state>][&do...

VIVOTEK 172 - User's Manual Example: Query the status of digital input 1 . Request: http://myserver/cgi-bin/dido/getdi.cgi?di1 Response: HTTP/1.0 200 OK\r\n Content-Type: text/plain\r\n Content-Length: 7\r\n \r\ndi1=1\r\n 8.3 Query Status of the Digital Output (capability.ndo > 0) Note: This requ...

VIVOTEK User's Manual - 173 \r\ndo1=1\r\n 8.4 3D Privacy Mask Note: This request requires admin user privilege <SD81X1> You can set privacy mask only at zoom 1x. To go back to zoom 1x directly, please send this cgi command: "/cgi-bin/camctrl/camposition.cgi?setzoom=0" Method: GET/POST ...

VIVOTEK 174 - User's Manual resolution> quality 1~5 3 The quality of the image. streamid 0~(m-1) <product dependent> The stream number. The server will return the most up-to-date snapshot of the selected channel and stream in JPEG format. The size and quality of the image will be set accord...

VIVOTEK User's Manual - 175 operator Operator privilege. admin Administrator privilege. Return <return page> Redirect to the page <return page> after the parameter is assigned . The <return page> can be a full URL path or relative path according to the current path. If you omit thi...

VIVOTEK 178 - User's Manual gaptime 0~32768 The gaptime between two consecutive ptz commands for device.(unit: ms) return <return page> Redirect to the page <return page> after the parameter is assigned . The <return page> can be a full URL path or relative path according to the cu...

VIVOTEK User's Manual - 181 8.13 Preset Locations (capability.ptzenabled) Note: This request requires Operator privileges. Method: GET/POST Syntax: http://< servername >/cgi-bin/operator/preset.cgi?[channel=<value>] [&addpos=<value>][&delpos=<value>][&return= <...

VIVOTEK User's Manual - 183 8.16 UART HTTP Tunnel Channel (capability.nuart > 0) Note: This request requires Operator privileges. Method: GET and POST Syntax: http://< servername >/cgi-bin/operator/uartchannel.cgi?[channel=<value>] -----------------------------------------------------...

VIVOTEK User's Manual - 185 8.18 Get SDP of Streams Note: This request requires Viewer access privileges. Method: GET/POST Syntax: http://< servername >/<network_rtsp_s<0~m-1>_accessname> “m” is the stream number. “network_accessname_<0~(m-1)>” is the accessname for stream “1...

VIVOTEK User's Manual - 195 CPUFlashRAM Image SensorMaximum ResolutionLens TypeFocal LengthApertureIrisField of View Shutter TimeWDR TechnologyDay/NightMinimum Illumination Pan/tilt/zoom FunctionalitiesIR Illuminators On-board Storage CompressionMaximum Frame Rate Maximum StreamsS/N RatioDynamic Ran...

VIVOTEK 196 - User's Manual Technology License Notice MPEG-4 AAC Technology THIS PRODUCT IS LICENSED UNDER THE MPEG-4 AAC AUDIO PATENT LICENSE� THIS PRODUCT MAY NOT BE DECOMPILED, REVERSE-ENGINEERED OR COPIED, EXCEPT WITH REGARD TO PC SOFTWARE, OF WHICH YOU MAY MAKE SINGLE COPIES FOR ARCHIVAL PURPOS...

VIVOTEK User's Manual - 197 Electromagnetic Compatibility (EMC) FCC Statement This device compiles with FCC Rules Part 15� Operation is subject to the following two conditions� ■ This device may not cause harmful interference, and■ This device must accept any interference received, including interfe...