Vivotek FD7130 - Manuals - manualsarea.com

Page 2 - Warning Before Installation

EN - 1 English Power off the Network Camera as soon as smoke or unusual odors are detected. Contact your distributor in the event of occurrence. Keep the Network Camera away from water. If the Network Camera becomes wet, power off immediately. Do not place the Network Camera around heat sources, suc...

Page 3 - Do not drop the Network Camera.

EN - 2 Do not place the Network Camera on unsteady surfaces. Do not touch the Network Camera during a lightning storm. Do not disassemble the Network Camera. Do not drop the Network Camera. Do not insert sharp or tiny objects into the Network Camera.

Page 4 - Software CD; Package Contents; Silica Gel

EN - 3 English Software CD FD7130 with an RJ45 or M12 Cable Quick Installation Guide / Warranty Card Screwdriver Alignment Sticker Ground Wire / Screws Liquid Tight Connectors for RJ45 or M12 Cable Package Contents 1 RJ45 M12 RJ45 Silica Gel

Page 5 - Physical Description; Inner View; Waterproof Level: IP66

EN - 4 N e t w o r k C a m e r a M o d e l N o : F D 7 1 3 0 M a d e i n Ta i w a n This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2) this device must accept any interference received, ...

Page 6 - Cabling Assembly; Assembling Steps; RJ45 Cable Connector

EN - 5 English 1 2 3 4 5 6 7 8 (D) (B) (C) (A) (E) Cabling Assembly 3 Components of the Waterproof Connector Screw Nut (C) Housing (D) Gasket (E) Seal (B) Sealing Nut (A) RJ45 Cable Dimension (unit: mm) Prepare an Ethernet cable and strip part of the sheath. Insert the housing into the screw nut. In...

Page 7 - M12 Cable Connector

EN - 6 1 2 3 4 5 6 7 Ø4.5mm~Ø6.5mm (C) (D) (B) (A) (E) M12 Cable Connector Components of the Waterproof Connector M12 Cable Dimension (unit: mm) Assembling Steps Clamp Ring (C) Gasket (D) Plastic Nut (E) Seal (B) Sealing Nut (A) Prepare an Ethernet cable and strip part of the sheath. Insert the seal...

Page 8 - Attach the supplied alignment sticker to the ceiling/wall.; Hardware Installation; Ceiling Mount

EN - 7 English First, use the supplied screwdriver to detach the dome cover from the camera base. Insert your MicroSD/SDHC Card if necessary. Then, follow the steps below to install the camera to either the ceiling or the wall: 1. Attach the supplied alignment sticker to the ceiling/wall. 2. Using t...

Page 9 - Wall Mount; Installing the Ground Wire

EN - 8 1 2 B A 3 4 Wall Mount Installing the Ground Wire As shown in the following ﬁgure, please secure one side of the supplied ground wire to the screw hole, then route the other side of the ground wire to the ground. Please secure the screws tightly to avoid moisture.

Page 10 - Network Deployment; PoE Switch; When using a non-PoE switch; PoE Power Injector

EN - 9 English Network Deployment 5 Power over Ether net (PoE) POWER COLLISION LINK RECEIVE PARTITION 1 2 3 4 5 PoE Switch When using a non-PoE switch Use a PoE power injector (optional) to connect between the Network Camera and a non-PoE switch. When using a PoE-enabled switch This Network Camera i...

Page 11 - lyzed, please click on the “Next” button to continue the program.; Assigning an IP Address

EN - 10 N e t w o r k C a m e r a M o d e l N o : F D 7 1 3 0 M a d e i n Ta i w a n This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2) this device must accept any interference received,...

Page 12 - Ready to Use; Access the Network Camera on the LAN.; To adjust the viewing angle; Adjusting the Lens

EN - 11 English For further setup, please refer to the user's manual on the software CD. Ready to Use 7 1. Access the Network Camera on the LAN. 2. Retrieve live video through a web browser or recording software. To adjust the viewing angle Adjust the lens to a desired viewing angle as the diagram s...

Page 13 - Completion; Fine-tune the Camera Focus; Tighten the lens lock screw.

EN - 12 Attach the dome cover to camera. Secure the dome screws with the supplied screwdriver. Finally, make sure all parts of the camera are securely installed. Completion 9 Fine-tune the Camera Focus The focus of this network camera is set from 1.0m to inﬁnity by factory default. If you want to fo...