Viking 201 - Manuals - manualsarea.com

Page 2 - IMPORTANT; Please Read and Follow; Table of Contents; Site Preparation; W A R N I N G

IMPORTANT 3 – Please Read and Follow Table of Contents Warnings & Important Information _____________________________________________________3Dimensions & Cutout Dimensions _____________________________________________________6Specifications __________________________________________________...

Page 3 - IMPORTANT–; Please Read and Follow!; ELECTRICAL SHOCK HAZARD; TIP OVER HAZARD; EXCESSIVE WEIGHT HAZARD; C A U T I O N

IMPORTANT 5 – Please Read and Follow 4 IMPORTANT– Please Read and Follow! W A R N I N G ELECTRICAL SHOCK HAZARD • Electrically ground dishwasher. • Connect ground wire to green ground connector in terminal box. • DO NOT use an extension cord. • Failure to follow these instructions, can result in dea...

Page 4 - Custom Panel

Specifications 7 Dimensions & Cutout Dimensions 6 28 -3/ 4” (73 .0 cm ) 33 -7/ 8” (86 .0 cm ) 49 ” (12 4.5 cm ) 23-7 /8” (60.6 cm ) 23-5/8” (60.0 cm) 3” (7.6 cm) 23-5/8” (60.0 cm) 26-5/8” (67.6 cm) 24” (61.0 cm ) 24 ” (61 .0 cm ) 34” min . (86 .4 cm ) to 35” min . (89 .0 cm ) Note: A 2” (5.1 cm)...

Page 5 - Locator; Custom Door Panel

9 2 2 1 1 x2 4 x2 3 Locators 2 x4 Pre-drill two holes with 1/8” drill bit for the locators using dimensions shown in the figure. Attach plastic locators using the Torx (T20 BIT) pan head screws provided in the hardware package. Pre-drill other four locations for wood screws to attach the panel to th...

Page 6 - Water Supply; General Information

11 • Read these instructions carefully and completely before installing thedishwasher. The installation should becarried out by a qualified installer, who isfamiliar with all local codes and ordinancesfor electrical and plumbing connections. Ifthe dishwasher is being installed for thefirst time, mos...

Page 7 - Hardwire Conduit Option; Grounding Instructions; Electrical Connections

13 5 1 2 1 1 6 2 Black(Line) White (Neutral) Hardwire Conduit Option (201 & 301 Models) 1 3 2 x4 2 1 3 3 x2 2 1 4 Remove front plate. Remove factory installed power cable from terminal block. Attach UL approved 3/4” strain relief (not included) to bottom of terminal box. Run wires through strain...

Page 9 - Counter Balance Spring Adjustment; Trim Installation Options

17 Counter Balance Spring Adjustment (if necessary) 1 1 2 1 2 2 Disconnect cable from hook. Remove spring from dishwasher. 3 Increase tension Decrease tension 1 4 2 Set counter balance spring connector in appropriate location. Reconnect cable to hook. Note: For custom panel installation, the door ma...

Page 10 - Installation; Leveling

19 2 1 6 DO WN UP 7a DO WN UP DO WN UP DO WN UP DO WN UP DOWN UP Equal distance 7b DO W N UP DO W N UP DO W N UP DO W N UP DO W N UP DO W N UP DO W N UP DO W N UP DO W N UP DO W N UP DO W N UP DO W N UP DO W N UP DO W N UP DO W N UP DO W N UP 1 2 Equal distance 8 Installation (cont.) Slide unit into...

Page 11 - Final Installation

21 12c Air Gap 12d Air Gap (Discharge with air gap) (Discharge with food waste disposer and air gap) 13 14 Connect water line. Plug LED light into dishwasher (select models only) and install kick plate. Note: DO NOT block the dry air exhausts (rectangular slots on the access panel) with kick plate o...

Page 12 - Service & Registration; These installation instructions should remain with the; Testing for Leaks; Final Preparation; Options; Unit Reset; Performance Checklist

23 Service & Registration Only authorized replacement parts may be used in performing service on the appliance. Do notrepair or replace any part of the appliance unless specifically recommended in the manual. Allservicing should be referred to a qualified technician. Contact Viking Range Corpora...