ViewSonic PJ700 - Manuals

2 ViewSonic PJ700 ENG L I SH Getting Started Congratulations on purchasing a ViewSonic PJ700 LCD projector! Save the original box and all packing material for future shipping needs. Package Contents • ViewSonic PJ700 LCD Projector• AC power cords (US, Europe, China)• ViewSonic Wizard CD-ROM (include...

ViewSonic PJ700 3 ENGL I SH Important Safety Warnings • Unplug the projector immediately if you detect an abnormal smell or see smoke.• Do not look directly into the lighted lens; doing so will cause severe eye injury.• Keep small children away from the projector . Children can be severely burned by...

4 ViewSonic PJ700 ENG L I SH Setting up the Projector 1 Connect the Power Cord and Input/Output Devices. Make sure that you have properly connected the power and input cables before turning on the projector. See “Connecting Input and Output Devices” on page 5. 2 Remove the lens cap. 3 Turn on the Pr...

ViewSonic PJ700 5 ENGL I SH Connecting Input and Output Devices Use Figure 3 below as a guide when connecting input and output devices to the ViewSonic PJ700 projector. The lines in the figure below demonstrate how various input devices can be connected to the ViewSonic PJ700 projector. For specific...

6 ViewSonic PJ700 ENG L I SH Positioning the Projector

ViewSonic PJ700 7 ENGL I SH Adjusting the Projector Angle Adjust the projector angle using the foot adjusters shown in Figure 5 below. See also Keystone under “Image Menu” on page 11. 1 Press the release button to lower the front foot, then tilt the projector up as shown in Figure 5 below. • The fro...

8 ViewSonic PJ700 ENG L I SH Using The Projector Use the control buttons on the projector control pad and the remote control to make quick adjustments to the controls listed in the following section. Control Buttons Press a control button to display a menu, then use the arrow buttons to adjust the s...

10 ViewSonic PJ700 ENG L I SH OnView Menus Use the OnView ® menus to make precise adjustments to the options described in the section below. To access and adjust the OnView menus, do the following: 1 Press the MENU button on the remote control or the projector control pad to display the OnView menus...

ViewSonic PJ700 11 ENGL I SH Input Menu Image Menu INPUT MenuThe Input menu displays the options described below: RGB (computer input only) displays the horizontal and vertical sync signal frequency of an RGB input source, such as a computer. Video (video input only) automatically detects and select...

12 ViewSonic PJ700 ENG L I SH Options Menu OPTIONS MenuThe Options menu displays the options described below: Volume increases or decreases the speaker loudness. Menu Color selects a background color for on-screen menus (Orange4 T

ViewSonic PJ700 13 ENGL I SH No Signal Menu NO SIGNAL MenuTo adjust projector settings before connecting input devices, use the No Signal menu to set the options below: Volume increases or decreases the speaker loudness. Keystone corrects image distortion that can occur when the angle of the project...

14 ViewSonic PJ700 ENG L I SH Other Information Specifications 1 May require a Macintosh adapter LCD TypePixelsColors Three 0.9” 800 x 600 polysilicon, active matrix TFT LCD480,000 (800 dots x 600 lines x 3 colors)16.7 million Lens TypeFocal lengthKeystone correction Manual zoom (1.2x), manual focus...

ViewSonic PJ700 15 ENGL I SH Timing Chart The following table lists the maximum refresh rates for standard resolutions (timing presets). Not all video cards can operate at these rates. See your graphics card user guide to ensure compatibility. Table 2: Computer Signal Rates and Resolution Resolution...

16 ViewSonic PJ700 ENG L I SH Troubleshooting No power • Make sure power button (or switch) is ON. • Make sure A/C power cord is securely connected to a power outlet.• Plug another electrical device (like a radio) into the power outlet to verify that the outlet is supplying proper voltage. Power is ...

18 ViewSonic PJ700 ENG L I SH Power Indicator Lights If the Lamp or Temperature indicator is red or flashing red when the ViewSonic PJ700 is turned on, there is a problem and you should not proceed. Turn off the projector and let it cool down. Table 3: Power Indicator Lights Power Indicator Lamp Ind...

ViewSonic PJ700 19 ENGL I SH Screen Messages Most screen messages disappear after 3 minutes and reappear when the unit is turned-on. Table 4: Screen Messages Screen Message Meaning or Action Required CHANGE THE LAMP AFTER REPLACING THE LAMP, RESET THE LAMP TIME The lamp service life is nearing its e...

20 ViewSonic PJ700 ENG L I SH Maintenance Projector Lamp Lamp Unit • To order a new lamp unit contact ViewSonic Customer Support.• Estimated lamp life is 1500 hours. WARNING: Make sure the power cord is disconnected and the unit is cool. Wait 45 minutes for the lamp to cool down. Figure 7: Lamp Repl...

ViewSonic PJ700 21 ENGL I SH Remote Control Battery Replace the battery when the remote control unit becomes difficult to operate (such as slow response when you push a button). Use a 3V lithium battery as shown in Figure 8. To replace the battery: 1 Pull the plastic tab from the battery access door...

22 ViewSonic PJ700 ENG L I SH Attaching the Optional Handle The ViewSonic PJ700 comes with an attachable handle. Follow the steps below to attach the handle. The handle hooks are on the left side of the projector, as shown in the figure to the left. If you choose to use the attachable handle, follow...

ViewSonic PJ700 23 ENGL I SH Customer Support For technical support or product service, see the table below or contact your reseller. NOTE: You will need the product serial number. Country/Region Web site T = TelephoneF = FAX Email United States Canada viewsonic.com/support viewsonic.com/support T: ...

24 ViewSonic PJ700 ENG L I SH Limited Warranty VIEWSONIC Projector What the warranty covers: ViewSonic ® warrants its products to be free from defects in material and workmanship during the warranty period. If a product proves to be defective in material or workmanship during the warranty period, Vi...

ViewSonic PJ700 25 ENGL I SH Appendix Power Cord Safety Guidelines Caution: Use a power cable that is properly grounded. Always use an AC power cord that meets your country’s safety standard. AC PLUG CORD PRECAUTIONS FOR THE UNITED KINGDOM FOR YOUR SAFETY PLEASE READ THE FOLLOWING TEXT CAREFULLY.IF ...

26 ViewSonic PJ700 ENG L I SH FCC Information This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. ...