Page 3 - user manual. The appearance of the product shall be subject to the; SHIPPING SCALE
- 1 - MODEL:5120 WARNING:For your personal safety, READ and UNDERSTAND before using.SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. DOUBLE INSULATIO Have product questions? Need technical support? Please feel free tocontact us: [email protected] NEED HELP? CONTACT US! This is the original instruction,...
Page 5 - GENERAL SAFETY RULES; Read all instructions. Failure to follow all instructions listed; SAVE THESE INSTRUCTIONS; Work area safety
- 3 - GENERAL SAFETY RULES WARNING! Read all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. The term"power tool" in all of the warnings listed below refers to yourmains-operated (corded) power tool or battery-operated (...
Page 6 - Personal Safety
- 4 - 7.Do not abuse the cord. Never use the cord for carrying, pulling orunplugging the power tool. Keep cord away from heat, oil, sharp edges ormoving parts. Damaged or entangled cords increase the risk of electricshock.8.When operating a power tool outdoors, use an extension cord suitablefor outd...
Page 8 - Table 1: Minimum gage for cord; Ampere Rating; SPECIFIC SAFETY RULES; Wear hearing protection during extended periods of operation.
- 6 - USE PROPER EXTENSION CORD. Make sure your extension cord is ingood condition. When using an extension cord, be sure to use one heavyenough to carry the current your product will draw. An undersized cord willcause a drop in line voltage resulting in loss of power and overheating.Table 1 shows t...
Page 9 - SAVE THESE INSTRUCTIONS.; MISUSE or failure to follow the safety rules stated in this
- 7 - 4.Handle the bits very carefully.5.Check the bit carefully for cracks or damage before operation. Replacecracked or damaged bits immediately.6.Avoid cutting nails. Inspect for and remove all nails from the workpiecebefore operation.7.Hold the tool firmly with both hands.Keep hands away from ro...
Page 10 - SYMBOLS
- 8 - SYMBOLS The followings show the symbols used for tool. Volts Amperes Hertz Alternating current No load speed Class II Construction Revolutions or reciprocation per minute
Page 11 - SPECIFICATIONS; Model; ACCESSORIES; DESCRIPTION; Wrench
- 9 - SPECIFICATIONS Model 5120 Ratings AC120V 60 Hz 15A Maximum Power 3.25HP ± 10% Collet Chuck Capacity 1/4" or 1/2" Plunge Capacity 0 - 50 mm No Load Speed 12000-23000RPM Net Weight 5.5 kg Due to our continuing programme of research and development, thespecifications herein are subject ...
Page 12 - CAUTION; FUNCTIONAL DESCRIPTION; Adjusting the depth of cut
- 10 - CAUTION These accessories or attachments are recommended for use with your toolspecified in the manual. The use of any other accessories or attachmentsmight present a risk of injury to persons. Only use accessory or attachmentfor this stated purpose. If you need any assistance with more detai...
Page 13 - Stopper block
- 11 - 1 2 3 lock lever and then lowering the tool body until the stopper pole makescontact with the adjusting hex bolt of the stopper block. Stopper block 1. Stopper pole2. Adjusting bolt3. Stopper block The stopper block has three adjusting hex bolts that raise or lower 0.8 mm(1/32") per turn....
Page 14 - Constant speed control
- 12 - Switch action CAUTION: Before plugging in the tool, always check to see that the switch triggeractuates properly and returns to the "OFF" position when released Make sure that the shaft lock is released before the switch is turnedon. To prevent the switch trigger from being accide...
Page 15 - Soft start feature; Soft start because of suppressed starting shock.
- 13 - Soft start feature Soft start because of suppressed starting shock. Speed adjusting dial Speed adjusting dial CAUTION: Before plugging in the tool, always check to see that the switch triggeractuates properly and returns to the "OFF" position when released The tool speed can b...
Page 16 - ASSEMBLY; Installing or removing the bit
- 14 - ASSEMBLY CAUTION: Always be sure that the tool is switched off and unplugged beforecarrying out any work on the tool Installing or removing the bit 1. Shaft lock2. Wrench CAUTION: Install the bit securely. Always use only the wrench provided with thetool. A loose or overtightened bit can ...
Page 17 - OPERATION
- 15 - OPERATION CAUTION: Before operation, always make sure that the tool body automaticallyrises to the upper limit and the bit does not protrude from the tool basewhen the lock lever is loosened. Before operation, always make sure that the chip deflector is installedproperly. Always use both ...
Page 18 - Straight guide
- 16 - 1. Feed direction2. Bit revolving direction3. Workpiece4. Straight guide Straight guide 1. Fine adjusting screw2. Guide holder3. Straight guide4. Clamping screw (B)5. Clamping screw (A) The straight guide is effectively used for straight cuts when chamfering orgrooving.Install the straight gu...
Page 19 - guide
- 17 - The templet guide provides a sleeve through which the bit passes, allowinguse of the tool with templet patterns. To install the templet guide, pull thelock plate lever and insert the templet guide. 1. Template guide2. Lock plate When cutting, move the tool with the guide roller riding the sid...
Page 22 - MAINTENANCE; Always be sure that the tool is switched off and unplugged before; Replacing carbon brush
- 20 - 1 MAINTENANCE CAUTION: Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. Replacing carbon brush 1.Limit mark Remove and check the carbon brushes regularly. Replace them when theywear down to the limit mark. Keep the carbon brush...
Page 26 - Made In China
- 24 - 58 ELASTIC ROUND PIN φ5X25 2 59 BASE PLATE 1 60 GUI HOLDER 1 616263 BUTTERFLY BOLT M6X10 2 64 STRAIGHT GUIDE 1 65 DUST NOZZLE 1 66 WRENCH 24 1 Made In China
