Uniden DXC834 - Manuals

Important Electrical Considerations Unplug all electrical appliances when you know an electrical storm is approaching. Lightning can pass throughyour household wiring and damage any device connected to it. This phone is no exception. Warning: Please do not attempt to unplug any appliance during an e...

Installation Selecting a Location Before choosing a location for your new phone, there are some important guidelines you should consider: • The location should be close to both a phone jack and continuous power outlet. Note: A continuous power outlet is an AC outlet which does not have a switch to i...

Desk or Tabletop Installation 1. Place the Baseon a desk ortabletop. 2. Plug the ACAdapter cord intothe 9V DC inputjack on the BaseUnit. 3. Place the ACAdapter cordaround the strainrelief. 4. Plug one end ofthe longtelephone cordinto the TEL LINEjack on the BaseUnit. 5. Plug the otherend of the cord...

Wall Installation Standard Wall Plate Mounting These phones are designed to be mounted on astandard AT&T or GTE wall plate. 1. Plug the ACAdapter intothe Base Unit. 2. Place the ACAdapter cordinside themoldedchannel. 3. Plug one endof the shorttelephone cordinto theTEL LINE jackon the BaseUnit. ...

Setting the Handset Retainer The handset retainer holds the Handset in place ifyour phone is mounted on a wall. The steps belowdescribe how to remove and replace the retainer sothat the tab faces up. 1. Push up on theHandsetretainer on theBase Unit, andslide the tabout. 2. Flip theretainer overso th...

Setting Up Your Phone Extending the Antenna Before using your phone, be sure to raise its antenna to the vertical position. Then, fully extend the antenna. Installing the Handset Battery Pack 1. Press in on theBattery CoverRelease. 2. Slide the batterycompartmentcover down. 3. Align the plasticconne...

Cleaning the Battery Contacts To maintain a good charge, it is important to clean all charging contacts on the Handset and Base Unit aboutonce a month. Use a pencil eraser or other contact cleaner. Do not use any liquids or solvents. Charging the Battery Pack Initial Battery Charging The rechargeabl...

Low Battery Indicator When the Battery Packin the Handset is verylow and needs to becharged, the TALK/BATTLOW LED flashes. If the TALK/BATT LOW LED begins to flash, the phoneis programmed to eliminate its functions to savepower. The table below describes what to do toreturn your phone to normal oper...

Using Your Phone Making and Receiving Calls The following features of the DX834 phone are different depending on the Handset’s location whenyou make or receive a call. Handset On Base Handset Off Base Answer Call Pick up Handset (AutoTalk) Press T . Make Call 1) Pick up Handset. 2) Press T . 3) List...

Programming Your Phone All programming functions must be completed whenyour phone is in the standby mode becauseprogramming keys do not function while you are onthe phone. Storing a Number in Memory Use these keys to store a number in memory. Note: An error tone will sound and the programmingprocedu...

Storing a Mixed Number If your phone is set up for Pulse dialing, you canstore a mixed mode number so that you can easilyaccess long distance services. Use these keys to store a mixed mode number inmemory.Note: An error tone will sound and the programmingprocedure will be canceled if more than 20 se...

Dialing a Stored Number To dial a number previously stored in memory, followthese steps: 1. Remove theHandset from theBase Unit. 2. Press T . 3. Press M . 4. Press the memory location number (0-9). Chain Dialing On certain occasions, after dialing a number, youmay be requested by the party or servic...

Erasing a Stored Number To erase a number previously stored in a memorylocation (0-9), follow these steps: 1. Remove theHandset fromthe Base Unit. 2. Press M twice. 3. Press the memory location number (0-9). Note: An error tone will sound and the erase procedure will be canceled if more than 20secon...

Troubleshooting If your DX834 Cordless Telephone is not performing to your expectations, please try these simple steps. If you are still unable to resolve the problems, contact Uniden Customer Service at (800) 297-1023,8:00 a.m. to 5:00 p.m. Central, Monday through Friday.

Specifications General – The DX834 complies with FCCParts15 and 68. Frequency Control PLL Modulation FM Operating Temperature -10 ° to 50 ° C Base Unit Receive Frequency 48.76 to 49.99 MHz Transmit Frequency 43.72 to 46.97 MHz Power Requirements 120V AC 60 Hz ± 3V AC Size 7-1/4 in. (H) x 4-3/4 in. (...

Addendum to Specifications General – The DX834 complies with FCCParts15 and 68. Frequency Control PLL Modulation FM Operating Temperature -10 ° to 50 ° C Base Unit Receive Frequency 48.76 to 49.99 MHz Transmit Frequency 43.72 to 46.97 MHz Power Requirements 120V AC 60 Hz ± 3V AC Size 8-1/2 in. (H) x...

PRECAUTIONS Before you read anything else, Please observe the following: WARNING! Uniden America Corporation DOES NOT represent this unit to be waterproof.To reduce the risk of fire, electrical shock, or damage to the unit, DO NOTexpose this unit to rain or moisture. RECHARGEABLE NICKEL-CADMIUM BATT...

One-Year Limited Warranty Important: Evidence of original purchase is required for warranty service. WARRANTOR: UNIDEN AMERICA CORPORATION (“Uniden”)ELEMENTS OF WARRANTY: Uniden warrants, for one year, to the original retail owner, this Uniden Product to be free from defects in materials andcraftsma...