Uniden DECT1363BK - Manuals

Base key and how it works Key (icon) What it does Find In standby: page the handset. - Handset keys/LEDs and how they work Key (icon) What it does Talk/Flash In standby: start a telephone call (get a dial tone).During a call: switch to a waiting call. - - End During a call: hang up.In the menu or an...

6 LED What it means sTaTUs On: the battery is charging.Blinking: there are new messages. - - Reading the Display This table shows possible status icons and what they mean. Since the icons appear based on what you're doing with the phone, you won't ever see all of these icons at the same time. Icon W...

7 Handset Setup Menu T-coil Turn on T-coil mode to reduce noise on some hearing aids (for more details, see page 13). Ringer Tones Choose the handset's ring tone. As you highlight each ring tone, the phone plays a sample. When you hear the tone you want, press MEnU/sElECT . AutoTalk Have the handset...

To switch to all capital letters, press * . The phone defaults to all capital letters first (e. g. ABCabc2) until you enter a blank space or press * again. (Any time you want to change case, just press * .) If two letters in a row use the same number key, enter the first letter and wait a few second...

Using the Caller ID and Redial Lists Caller ID (CID) is a service available from your telephone provider that shows the phone number (and sometimes the caller’s name) of incoming calls. Contact your telephone provider for more information. Caller ID list Redial list When a call comes in, the phone d...

10 Using Call Waiting Call Waiting, a service available from your telephone provider, lets you receive calls while you are on another call. Caller ID on Call Waiting (CIDCW) service displays Caller ID information for a waiting call.If you get a Call Waiting call, the phone sounds a tone and displays...

11 Phonebook Entry Options With the phone in standby, open the phonebook and find the entry you want. Press MEnU/sElECT to open the individual phonebook entry menu. The phone prompts you to edit or delete the entry. Finding the Handset With the phone in standby, press Find on the base. The handset w...

12 Select Edit Voice Mail . Enter the access number (up to 20 digits) that your voice mail provider gave you. Be sure to enter the number exactly as you would dial it. When you’re finished, press MEnU/sElECT . To access your mailbox, just press MEssagEs/MUTE-ClEar when the phone is in standby. The p...

1 If… Try… The handset won’t display CID information. Letting calls ring twice before answering.Making sure your CID service is active. - - I hear a beeping during a call. The battery is getting low. Check the handset for a low battery alert. Finish your conversation and return the handset to the cr...

14 If static is in 1 location: If static is in all locations: Check nearby for one of the common interference sources.Try moving the handset away from a suspected source, or try moving the suspected source so it’s not between the handset and the base.There is always more noise at the edges of the ba...

1 handset Base Remove the battery cover and disconnect the battery. Let dry for at least 3 days with the battery disconnected and the cover off for ventilation.After the handset dries, reconnect the battery and replace the cover. Recharge the battery fully (15-20 hours) before using. 1. 2. 3. Discon...

16 Cadmium and Nickel are chemicals known to the State of California to cause cancer. Do not short-circuit the battery. The rechargeable Ni-Cd batteries contained in this equipment may explode if disposed of in a fire. Do not charge the battery used in this equipment in any charger other than the on...

17 ringing in response to an incoming call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the telephone provider. The REN for this product is part of the produc...

1 FCC Part 15 information This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interfer- ence that may cause undesired operati...

1 Industry Canada (I.C.) Notice Terminal equipment NOTICE: This equipment meets the applicable Industry Canada Terminal Industry Canada Terminal Equipment Technical Specifications. This is confirmed by the registration number. The abbreviation IC before the registration number signifies that registr...