Uniden BTS200 - Manuals

English - 5 SET UP YOUR BTS200 SPEAKER Install the Battery 1. Remove the battery from any protective packaging and discard the packaging accordingly. 2. Align the battery pack with the guides along the inside of the battery area. Be sure the contact slots are in the correct position to close on the ...

6 - English 1. Press and hold for at least 3 seconds. 2. All LEDs light and a power on tone sounds. 3. and LEDs go out. 4. flashes slowly while looking for Bluetooth devices. It remains steady on when Bluetooth devices are discovered; otherwise, it goes out. To turn off the speaker: Press and hold f...

English - 7 Pair Second Bluetooth Device 1. Turn on your speaker, and continue to press and hold until the speaker beeps twice. 2. Release . The BTS200 is ready to pair. 3. Follow the same procedures for pairing your first Bluetooth device (see page 6). GETTING TO KNOW THE BTS200 SPEAKER BTS200 Top/...

English - 9 BTS200 Back Bass output 3.5mm Audio In jack Power adapter input Use this... To... Audio In Insert the audio cable’s plug. Bass output Hear the bass sound. DC 5.4V Insert the power adapter.

10 - English LEDs Icon Status Meaning Power On (green) BTS200 is turned on and operating. Off BTS200 is turned off. Bluetooth Slow blink BTS200 is looking for paired Bluetooth devices. Fast blink BTS200 is ready to pair to a Bluetooth device. Steady on BTS200 is connected to a Bluetooth device. Off ...

English - 11 Basic Cell Phone Operations The green LED flashes when your cellphone has an incoming call. Both the speaker and your cellphone may ring, depending on your cellphone settings. To... Do this... Answer an incoming call Press . Reject an incoming call Press and hold and . End a call Press ...

12 - English Call Waiting You can receive call waiting notification when your cellphone is paired to your speaker. The LED flashes and your speaker sounds an alert tone. Your cellphone must subscribe to Call Waiting service to use these features; contact your telephone provider for more information....

English - 13 Basic Music Operation When you pair a Bluetooth music player to your speaker, you can control operation through your speaker. To... Do this... Play music Press . NOTE: When you stop or pause the music playback, your speaker starts streaming music into a buffer. The music resumes at the ...

14 - English SPECIAL FEATURES Charge Cellphone using a USB Cable If you have the proper fitting USB cable (not included), you can charge your cellphone through your speaker. Be sure you have a USB cable that will fit both USB connections - the one on your speaker and the one on your cellphone.1. Con...

English - 15 The following restrictions apply when you are playing music through a wired connection: • If both a Bluetooth device and a wired device are connected to your speaker, the Bluetooth device will take priority over the wired device. • The BTS200 does not control the wired device; it only p...

16 - English TROUBLESHOOTING If this happens... Try this... Bluetooth device disconnects Press to reconnect. Bluetooth device disconnects due to Out of Range After moving back into connection range, press key for reconnection. Sound is not clear or there is no sound at all Check BTS200 or your Bluet...

English - 17 If this happens... Try this... Sound is too small / too much distortion Adjust the volume level of BTS200 or Bluetooth device. Phone call not answer by BTS200 – Make sure your cellphone has HFP. – Check if both devices are connected. – Restart BTS200 for auto-connecting with your Blueto...

18 - English Battery Features Your BTS200 comes equipped with a rechargeable Lithium-Ion polymer battery. You can recharge the battery by connecting it to 120 VAC power through the AC adapter. Install and Charge the Battery See page 5 for details on installing and charging the battery (the same proc...

English - 19 • 0 LEDs = Less than 15% power remaining. When the battery level falls below 15% (0 LED) status, the speaker sounds alert tones (four-beep pattern). SPECIFICATIONS • Total 4W output (2W / Channel) • Full-range (50mm) driver / Channel + Passive Radiator • Li-Ion polymer Batt: 2950mAh • P...

20 - English FCC Notice This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. ...

English - 21 Industry Canada statement This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may ...